he canvas redrawing and the Rhino viewport redrawing take some time as well (on my system 6 ms for the empty Gh canvas and 28 ms for the empty Rhino viewport). No timer can avoid that, to my knowledge. The trampoline computes timing after the solution is complete. This means that one cycle is: solution completed + drawn + user specified interval.
Hope that this helps to get started,
- Giulio________________giulio@mcneel.com…
Delaunay triangulations maximizes the minimum angle of all the angles of the triangles in the triangulation; they tend to avoid skinny triangles.
In order to obtain a valuable (quality) mesh at a given minimum angle for triangles (here 15 degrees), I advise to implement Chew Second Algorithm (see : http://2011.cccg.ca/PDFschedule/papers/paper91.pdf).
Then, the control of triangle lengths should be done by pruning edges below 28 inches.
Do not hesitate to contact me.…
stricts). This will tell me which properties within the set exist in more than one zone.
I've gotten this far, but cant seem to get a set of all the property lines that are crossed by zoning lines. From using GIS, I know the answer should contain 28 properties.
I've attached what I've done so far, any help would be appreciated.
…
Added by Eric Galipo at 11:40am on January 13, 2016
another comma separated txt file. I know how to import points (function Import coordinates), but I dont know how to connect them by lines if the only information I have about lines is the list of point numbers which should be connected. The txt file with point coordinates looks like:
-18,-36,-1000-18,-34,-19.728-18,-32,-17.603-18,-30,-15.372-18,-28,-13.121
...
And the txt file with line connections looks like:
1,22,33,44,55,6
...
Which means that I want to connect point 1 with point 2, point 2 with point 3 etc...
Both txt files are attached, thank you for the answer...…
p;biw=1680&bih=925&tbm=isch&tbnid=UQXK-STjeJrGhM:&imgrefurl=http://www.grasshopper3d.com/forum/topics/sinusoidal-facade&docid=XRgBzjBowOStWM&imgurl=http://storage.ning.com/topology/rest/1.0/file/get/2768634805?profile=original&w=1805&h=727&ei=itp3UbHLCvDs0gWy-oGQCA&zoom=1&ved=1t:3588,r:0,s:0,i:80&iact=rc&dur=487&page=1&tbnh=141&tbnw=340&start=0&ndsp=28&tx=217&ty=36
But somehow, it doesn't seem to work when i do the same.. does anyone know why?
Regards, Rutger…
are not copy with the number that belong to each other, like:
untrimmed surface0 should be 41 pieces
untrimmed surface1 should be 28 pieces
untrimmed surface1 should be 21 pieces
it result like this
exclude the 1st and 2nd pieces,the others all is untrimmed surface 1
and the attachments is the result that i want, I done it one by one.…
in green in the below screenshot) and it was fine in generating different stochastic aggregation outputs but when I shift to a slightly more complex geometry (in blue in below screenshot), the component has an error that reads " could not place 28 parts".
I've attached the .gh file with internalized data, any help would be awesome!
Thanks in advance (:
…
Added by vhwt to Wasp at 10:32pm on September 22, 2021
he installation folder, Drag & drop SYNTACTIC(green one) over your grasshopper canvas.3. Close your rhino and reopen it. 4. Type GrasshopperDeveloperSettings5. Tick the Memory load *.GHA assemblies using COFF byte arrays option6. Run grasshopper and enjoy plugin…