6, 7, 8, 9, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28, 30, etc
In addition to the components in the attached file, I have also tried using Cull Index but that did not do much. I tried using a number slider set to whole numbers with the range equal to the values I have set up in the integer, but it just increases the size by 1 every time. Any help on steps in the right direction would be great thanks.…
NONE, in SIZING:PARAMETERS". I'm not sure of where to start in troubleshooting this. I've attached the file.
Thank you,
See the errors and warnings below:
{0;0;0}
0. Current document units is in Meters
1. Conversion to Meters will be applied = 1.000
2. [1 of 8] Writing simulation parameters...
3. [2 of 8] Writing context surfaces...
4. [2 of 8] Writing context surfaces...
5. [3 of 8] Writing geometry...
6. [4 of 8] Writing Electric Load Center - Generator specifications ...
7. [5 of 8] Writing materials and constructions...
8. [6 of 8] Writing schedules...
9. [7 of 8] Writing loads and ideal air system...
10. [8 of 8] Writing outputs...
11. ...
... idf file is successfully written to : R:\Green\SuRG\Building_Performance_Analysis\2016_analysis_studies\Energy_Analysis_Comparison\Honeybee_+_Ladybug\tutorial01\EnergyPlus\tutorial01.idf
12.
13. Analysis is running!...
14. ...
...
Done! Read below for errors and warnings:
15.
16. Program Version,EnergyPlus, Version 8.5.0-c87e61b44b, YMD=2016.10.31 11:39,IDD_Version 8.5.0
17.
18. ************* IDF Context for following error/warning message:
19.
20. ************* Note -- lines truncated at 300 characters, if necessary...
21.
22. ************* 24 Sizing:Parameters,
23.
24. ************* Only last 1 lines before error line shown.....
25.
26. ************* 25 None, !- Heating Sizing Factor
27.
28. ** Severe ** IP: IDF line~25 Invalid Number in Numeric Field#1 (Heating Sizing Factor), value=NONE, in SIZING:PARAMETERS
29.
30. ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
31.
32. ** ~~~ ** Possible Invalid Numerics or other problems
33.
34. ** Fatal ** IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination.
35.
36. ...Summary of Errors that led to program termination:
37.
38. ..... Reference severe error count=1
39.
40. ..... Last severe error=IP: IDF line~
, value=NONE, in SIZING:PARAMETERS
41.
42. ************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).
43.
44. ************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.
45.
46. ************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
47.
48. ************* EnergyPlus Sizing Error Summary. During Sizing: 0 Warning; 0 Severe Errors.
49.
50. ************* EnergyPlus Terminated--Fatal Error Detected. 1 Warning; 1 Severe Errors; Elapsed Time=00hr 00min 9.34sec
51.…
a follow up question... how do I wrap a list onto itself at a certain frequency?
i.e. I want the list {1;2;3;4;5;6;7;8;9}
to become {1,4,7; 2,6,8; 3,6,9} wrapped every 3rd item
Added by Joshua Jordan at 5:30pm on November 17, 2012
he same order of the list. for example i have a list with 4 different lenght of curve like this:
0= 10
1= 12
2= 8 (minimum)
3= 17 (maximum)
and wont to make a ranking that the longest curve gets the value 4 and the smallest the value 1, like this
0= 2
1= 3
2= 1
3= 4
i tried the sort list function, but it dosn`t work
can anybody help me!
thx a lot…
s suivantes
{0;0} {0;0}
0=longueur (300) 0=longueur (400)
1=largeur (8) 1=largeur (6)
2=hauteur (20) 2=hauteur (8)
{0;1} {0;1}
0=longueur (250) 0=longueur (250)
1=largeur (8) 1=largeur (8)
2=hauteur (12) 2=hauteur (12)
{0;2} {0;2}
0=longueur (400) 0=longueur (300)
1=largeur (6) 1=largeur (8)
2=hauteur (8) 2=hauteur (20)
je souhaite réorganiser mes listes en fonction de la croissance de l'item 1 (soit la largeur) puis en fonction de l'item 2 (la hauteur) néanmoins pour chacune de ces listes les items sont indissociables .
dans l'exemple de gauche la liste de rhino et dans l'exemple de droite la liste que je souhaite obtenir c'est d'abord la largeur qui va croissante puis ,lorsque les largeurs sont identiques ce sont les hauteurs qui vont dans l'ordre croissant .Les longueurs restent assignées à la liste.…
oning behind using the equality component to test for even numbers is flawed because of the data matching used by gh. It is testing like this:
0==0 True
2==1 False
4==2 False
6==3 False
etc
.............
Where as a Modulo 2 would work like this
0%2 = 0
1%2 = 1
2%2 = 0
3%2 = 1
4%2 = 0
5%2 = 1
6%2 = 0
7%2 = 1
8%2 = 0
9%2 = 1
......
Also I notice you have some errors in your expressions producing Nulls.
If you want it to be twice the value then you should have 2*D in the Expression and 10*D in the other
....
I attach a working version.…
problem is that I am inputting 8 points and getting 24 point out because grasshopper is matching every point to every surface. The correct way would be 3 points for surface {0}, 3 points for surface {1}, and 2 points for surface {2}.
Anyway, is there a way to say that every branch with a {0;?} should relate to the {0} surface, the {1;?} branches should match with the {1} surface, etc?
…