ey provide all the means to what I try to achieve.
What I need is to get a fast (as possible) evaluation of passive heat/solar gain from a certain facade. I know my building can cool to a certain degree (lets say 80 W/m2 - now lets forget other internal gains) and I want to be sure my facade is not letting excessive amounts of heat into the room/building. Normally I would make a full blown simulation to count my overheating hours and thereby evaluate my facade. To speed up the process, the idea is just to evaluate overheating hours in a faster way. So what I am thinking is that excessive amounts may estimated by counting high intensity irradiation patches in a critical sky-component or whatever such thing would be called that surpasses my sensible cooling load. My hope is that any facade visible to the sky-patches would very similar to the number of overheating hours if properly calibrated to a simulated model. However I have no idea right now, if this can be done.
Why do this? Speed, convenience, whole building thermal analyses.
@Chris and @Abraham The critical sky-component is made with LBs radiance component radiation and filtering the beam-components with highest effects from a yearly epw-file.
@Chris Conductive heat gains are also important especially if the facade is badly insulated, so the next step is to filter the outdoor temperature parallel with that critical sky-component and then do a static heat transfer analysis and combine that with the effect from direct sun influence. Again, no idea if it works.
Hope it makes sense. I a little embarrassed I drew you into this little experiment. This was not at all the point of the discussion. But now we are into it I like to know what you think. If it works its kinda neat, at least i think it is.
/K…
pts organize in a data tree without losing the data structure. To create a folding surface as per image attach.
1. Replace items (to create a gradient) / Like the weight culling example.
Path {0} replace all indexes with a new value (a)
Path {1} replace 90% indexes with a new value (a)
Path {2} replace 80% indexes ...
2. Decrease value (a) in relation to path number
3. After Replace the above items value with
for even path number {0,2,...} replace items with a negative number
Did not find a easy way to create data tree that would achieve the above inside GH.
Point 2 & 3 are easy but i could not found a simple solution for points 1.
At the moment the only way i found is to create the list in Excell manually and import/ export or to create a list on indices for each path.
Any hint appreciated.
Might need to wait for the number slider or path mapper to accept input or notation ?
best
Stephane
…
rld.wolfram.com/EnnepersMinimalSurface.html
when i type the equations for z,y,z it says a syntax error so i obviously do not understand how to construct an expression. (screen capture attached)
Any help/explanation of using this function would be greatly appreciated
thanks so much
Capture.JPG…
a pain to use sometimes. I recently found this great post:
http://www.grasshopper3d.com/forum/topics/formatting-numbers-in-grasshopper
which points to the msdn .net framework standard numeric format strings:
http://msdn.microsoft.com/en-us/library/dwhawy9k.aspx
and the custom ones too:
http://msdn.microsoft.com/en-us/library/0c899ak8.aspx
Sooo... today I was trying to make a 2D array generator for RGB values to use with a RGB LED and an Arduino. For instance, declaring a 2D array in Arduino:
int color[3][3]={{255,0,0},{0,255,0},{0,0,255}};
I'm using the blend color component to spit out transitions between two colors. I want the list in the panel to be in the format above, so I used both the expression component and the string format component (are they the same under the hood?). In any case, if I have R, G and B values coming into the component, I want to format them so the come out looking like {R,G,B}, so I can just copy the output in a panel and paste it into the Arduino IDE. But what about {curly braces}. If the expression/format component uses them in it's syntax, for instance:
Format ("{R:0},{G:0},{B:0}",R,G,B)
how do I get them into the formatting string? I tried escaping them like:
Format ("\{{R:0},{G:0},{B:0}\}",R,G,B)
but that just makes the component angry
Escaping characters is explained in the formatting references above. Is it implemented in this component? Should I be looking at a different approach?
I've included a sample file below.
Thanks!
~BB~
…
ing-in-python?commentId=2985220%3AComment%3A628495
For the most part, I got the serial port to work and I could share the port with other components without wiring the components together using a sticky Python dictionary. There were a couple of issues with closing the port (Rhino had to be restarted).
In any case, I'm back at it. I am however going the C# component route with an eye towards writing my own components with visual studio. I am trying to create bidirectional communication with a serial device in grasshopper. I need more control over the serial port that the generic Firefly components can afford. Furthermore, I would like to understand how to program this myself. The first goal would be to create a few components that could handle various serial tasks, one to open/close port, one to read from port and one to write to it. This is not unlike how I got it to work in python, and is also similar to the logic in Firefly's serial components.
The thing that has me stumped with C# is how one shares the port between components? If one component is responsible for creating and opening/closing the port, how do the read/write components address the instance of the port created in the other component? Python has the sticky dictionary, is there something similar in C#? I'm a novice when it comes to C# and how it works within grasshopper, so maybe I'm missing something simple.
I've attached a klunky definition that uses C# to open/close a serial port. I've tried accessing the port with other components, but I don't know enough to make it work. Again, I'm mainly interested in the mechanics of how one component can access the serial port instance created in another component. If I could get some user objects going for now, I'd be happy. In the future, I want to roll my own components. If anyone has any suggestions, code snippets, or any other forms of enlightenment, I'd be greatly appreciative!
Rhino5 x64 + GH version 0.9.0056
Thanks,
~BB~
…
hen you determine their position and number by the "precision_" input. Their number is equal to "precision_ - 1".They are essentially mesh edges, not curves. To hide them, in Rhino application menu choose: Tools -> Options -> View -> Display Modes -> choose your current display mode, and uncheck the "Show mesh wires":
b) How do you change the x- and y-scale of the chart? For instance displaying every 10 degrees of azimuth?
Can you be a bit more precise?You would like to change the labeling of the azimuth directions from 30 degrees step to 10 degrees step? If this is so, you can not do that.
c) My input surface is a hyperbolic paraboloid, facing south symmetrically. How does the component calculate its tilt and azimuth?
All Ladybug Photovoltaics components calculate the amount of AC energy generated by a planar (flat) surface. Tilt and azimuth angles are calculated based on surface normal at 0.5, 0.5 surface parameters. So you can not use the hyperbolic paraboloid as the _PVsurface (or _PV_SWHsurface) input, as it will yield incorrect results. You need to planarize that hyperbolic paraboloid surface first.I attached below an example with default grasshopper components, but the size of the panels is not equal. If you want them to be equal use some paneling Grasshopper plugin like Lunchbox or Paneling tools.…
eventually found out about genetic algorithms on which I found extensive researches, projects,... ! I looked into it and ended up on a few papers which I believe are the jumpstart for my master thesis.
"Galapagos; on the logic and limitations of generic solvers" by David RuttenArticle in Architectural Design 83(2) March 2013
"Black-box optimisation methods for architectural design" by Thomas Wortmann and Giacomo NanniciniConference Paper: CAADRIA 2016, At Melbourne, AU, Volume: 177-186
So I started looking into alternatives to genetic algorithms in architectural design.So far, I've ended up on :
Thomas Wortmann's work with the surrogate(or model) based optimization approach!You can check out the tool he developped for GH (Opossum):http://www.food4rhino.com/app/opossum-optimization-solver-surrogate-models
Judyta Cichocka's work, specially with the Swarm approachYou can check out the tool she developped for GH (Silvereye):http://www.food4rhino.com/app/silvereye-pso-based-solver
And that's it !!! I've been researching through article references (mainly on "researchgate") but I'm now stuck in a loop of references I already visited!That probably means the litterature on the subject is not (yet) extended but I might probably be missing something.The keywords make it difficult to search : "optimisation", "algorithms", "architecture", send me most of the time to computational engineering and deep mathematics papers I unfortunately do not have the background knowledge to comprehend ! So there it is ! If you have any clue of where (or how ! ) I should be looking, please tell me :)I know Mr Rutten is pretty active on the forum so hopefully... (fingers crossed :p) !Also if you have any good tips for getting into algorithms in general (you think could help), I'd be glad to hear(read) it ! A book, tutorials maybe ?!So, autors, architects, projects books, articles, conferences I should go to,specialized architecture offices/studios (I'm also looking for an internship so ...).If you know about a more appropriate forum please let me know !If you want to get deeper into this, you can contact me at :
e1635331@student.tuwien.ac.at
tdissaux@student.ulg.ac.be
My master thesis is due for may 2018 but I have a paper to write for January 2018 in order to be elligible for a PHD program afterwards.What I mean by that is that if you read this message in 6 month, I'll still be open to discussion !
I am right now an erasmus student at TUWien (Vienna) but my main university is The university of Liège in Belgium.I can handle French, English, Italian litterature and eventually Dutch if really you think it's worth it ! I have access to most online libraries via my university's portals so access shouldn't be an issue !I'm very excited to hear from you I wish you all a great day,Cheers,Thomas
…
thought that architect's love for drawing comes from the necessity of translate abstract ideas into built 3D reality, and the technology behind that 2D representation has not evolve so much until some decades ago. Our teachers come from that times: times when computers try to find their place in the reality representation world. If you try to imagine that people that have always drawn with pencils adapting to this new tools...some become fan of new methods, other just keep the old fashion workflow (like Andrew said in the article, Schumacher VS Graves)
We've bear (at least Andrew and me :P) in 80's with first video games, computers (I still remember my old x286 with 1Mb RAM and 20Mb of HD and that MS-DOS interface)...New technology was natural for us...But there is a big difference between traditional drawing and new computer aided tools: the learning curve. To draw you only need to take a pen and put over a paper (that interface is understood by children easily) , but traditional computational tools (new touch interfaces are out of this group) are based in a complex logic and environment that is not easy to understand for some people.
In the workshops I'm teaching in, I try to put all that tools (new and old one) in my students hands and motivate them to mix and use them together (Andrew knows a little bit about that :P). Why not to make a lines sketch with GH and then print it and render with some markers?; the last step could be scan the result and enhance it in Photoshop adding textures, vegetation, some background...There are no rules, only a bunch of tools to explore and use to develop your ideas, evolve and finally represent them.
I bet to the touch interfaces (with some augmented reality sauce) like that one that will be able to blend both worlds, analog and digital, offering that fluidity and natural interaction that Grave miss in digital tools. And our generation attached to this "not natural" interfaces will need to change its mind and adapt to that new and amazing interface that our children will love.
Only to complete:
<iframe width="560" height="315" src="http://www.youtube.com/embed/aXV-yaFmQNk" frameborder="0" allowfullscreen></iframe>…
Added by Ángel Linares at 5:40pm on September 10, 2012
e volume. The yellow line above.
This volume, green on the above image
So with this there was an intersection with the Brep volume of the chair and the lattice.
After that I used cocoon. Here the parameters I used for the Brep and curve. So The Brep was offsetted.
The model is 80 unit height and cell size is 0.2 so roughly there are 400 divisions in Z. If cubic it will give 6.4 millions of cells. To my point of view it is important to choose well the cell size in order to have not hundred of million of cells. Here 6 millions was usable. The general thing with Cocoon is alwas to test it on small objects first.
A close view of mesh. Edge length is 0.1 unit. There are 6 millions of triangles.
…