t defined from the discussion of radiation exchange between urban surfaces and the sky in urban heat island research (See Oke's literature list below). It will be affected by the proportion of sky visible from a given calculation point on a surface (vertical or horizontal) as a result of the obstruction of urban geometry, but it is not entirely associated with the solid angle subtended by the visible sky patch/patches.
So, I think using "geometry way" to approximate Sky View Factor is not correct. Sky View Factor calculation shall be based on the first principle defining the concept: radiation exchange between urban surface and sky hemisphere:
(image extracted from Johnson, G. T., & Watson, 1984)
Therefore, I always refer to the following "theoretical" Sky View Factors calculated at the centre of an infinitely long street canyon with different Height-to-width ratios in Oke's original paper (1981) as the ultimate benchmark to validate different methods to calculate SVF:
So, I agree with Compagnon (2004) on the method he used to calculate SVF: a simple radiation (or illuminance) simulation using a uniform sky.
The following images are the results of the workflow I built in the procedural modeling software Houdini (using its python library) according to this principle by calling Radiance to do the simulation and calculation, and the SVF values calculated for different canyon H/W ratios (shown at the bottom of each image) are very close to the values shown in Oke's paper.
H/W=0.25, SVF=0.895
H/W=1, SVF=0.447
H/W=2, SVF=0.246
It seems that the Sky View Factor calculated from the viewAnalysis component in Ladybug is not aligned with Oke's result for a given H/W ration: (GH file attached)
According to the definition shown in this component, I assume the value calculated is the percentage of visible sky which is a geometric calculation (shooting evenly distributed rays from sensor point to the sky and calculate the ratio of rays not blocked by urban geometry?), i.e solid angle subtended by visible sky patches, and it is not aligned with the original radiation exchange definition of Sky View Factor.
I'd suggest to call this geometrically calculated ratio of visible sky "Sky Exposure Factor" which is "true" to its definition and way of calculation (see the paper on Sky Exposure Factor below) so as to avoid confusion with "The Sky View Factor based on radiation exchange" as discussed in urban climate literature.
Appreciate your comments and advice!
References:
SVF: definition based on first principle
Oke, T. R. (1981). Canyon geometry and the nocturnal urban heat island: comparison of scale model and field observations. Journal of Climatology, 1(3), 237-254.
Oke, T. R. (1987). Boundary layer climates (2nd ed.). London ; New York: Methuen.
Johnson, G. T., & Watson, I. D. (1984). The Determination of View-Factors in Urban Canyons. Journal of American Meteorological Society, 23, 329-335.
Watson, I. D., & Johnson, G. T. (1987). Graphical estimation of sky view-factors in urban environments. INTERNATIONAL JOURNAL OF CLIMATOLOGY, 7(2), 193-197. doi: 10.1002/joc.3370070210
Papers on SVF calculation:
Brown, M. J., Grimmond, S., & Ratti, C. (2001). Comparison of Methodologies for Computing Sky View Factor in Urban Environments. Los Alamos, New Mexico, USA: Los Alamos National Laboratory.
SVF calculation based on first principle:
Compagnon, R. (2004). Solar and daylight availability in the urban fabric. Energy and Buildings, 36(4), 321-328.
paper on Sky Exposure Factor:
Zhang, J., Heng, C. K., Malone-Lee, L. C., Hii, D. J. C., Janssen, P., Leung, K. S., & Tan, B. K. (2012). Evaluating environmental implications of density: A comparative case study on the relationship between density, urban block typology and sky exposure. Automation in Construction, 22, 90-101. doi: 10.1016/j.autcon.2011.06.011
…
2: https://vimeo.com/107502226
------------------------------------------------------------------------------------------------
Hi all,
1. Chris, Chien Si and I will present Ladybug and Honeybee at IBSA-USA NYC this Thursday (August 21st). The presentation will include some of the latest developments that we are working on. If you are interested to know more about some of the new developments and see some of the workflows and you are around New York then just stop by. If can't attend in person you can still watch the presentation online. Check the links below. (Make sure to register by Wednesday if you are attending in person.)
2. We would like to show some of the works that you have done with Honeybee and Ladybug during the presentation so if there is anything that you think is interesting and can be presented publicly send it to us at thisisladybug@gmail.com or just post it here. Make sure to let us know who do you want us to credit the image.
3. That's it for now. I copy the information about the presentation below and hope to see some of you there. Thanks for your help and support.
Cheers,
Mostapha
IBPSA-USA New York Regional Chapter presents:
Parametric Modeling Tools | Ladybug and Honeybee
Location: Thornton Tomasetti, 44 East 27th street (between Madison and Park)
Date & Time: Thursday, August 21, 2014 - 6:00-7:30 PM.
6:00-6:30 PM Networking
6:30-7:30 PM Ladybug and Honeybee
Mostapha Sadeghipour Roudsari, Thornton Tomasetti
Chris Mackey, MIT
Chien Si Harriman, Terabuild
7:30-7:45 PM Q & A
Click here to register**: https://attendee.gotowebinar.com/register/6507378565592582402
**Please register at least a day in advance if you wish to attend in person
Descriptions
Ladybug + Honeybee
Ladybug and Honeybee are open source environmental plugins for Grasshopper that help architects and engineers create an environmentally-conscious architectural design.
Ladybug imports standard EnergyPlus Weather files (.EPW) into Grasshopper and provides a variety of 3D interactive graphics to support the decision-making process during the initial stages of design. The plugin also provides further support for designers as they test their initial design options with radiation, sunlight-hour, and shading analyses. Integration with Grasshopper allows for an almost instantaneous feedback and, since the plugin runs within the design environment, the information and analyses are interactive.
Honeybee connects Grasshopper3D to EnergyPlus, Radiance, Daysim and OpenStudio for building energy and daylighting simulation. The Honeybee project intends to make many of the features of these simulation tools available in a parametric way. Just as users have made changes to geometry for years in Grasshopper, now users can parameterize system types, zoning schemes, schedules of operation, daylight sensor placement and controls - all of the “hardcore” simulation parameters that have never been exposed to parametric modeling tools.
https://www.facebook.com/LadyBugforGrasshopper http://www.grasshopper3d.com/group/ladybug
…
ting.
Thanks
Rania
** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
** Warning ** Version: in IDF="'8.2.7'" not the same as expected="8.2"
** Warning ** ManageSizing: For a zone sizing run, there must be at least 1 Sizing:Zone input object. SimulationControl Zone Sizing option ignored.
** Warning ** ManageSizing: For a plant sizing run, there must be at least 1 Sizing:Plant object input. SimulationControl Plant Sizing option ignored.
************* Testing Individual Branch Integrity
************* All Branches passed integrity testing
************* Testing Individual Supply Air Path Integrity
************* All Supply Air Paths passed integrity testing
************* Testing Individual Return Air Path Integrity
************* All Return Air Paths passed integrity testing
************* No node connection errors were found.
************* Beginning Simulation
************* Simulation Error Summary *************
** Warning ** The following Report Variables were requested but not generated
** ~~~ ** because IDF did not contain these elements or misspelled variable name -- check .rdd file
************* Key=*, VarName=ZONE IDEAL LOADS SUPPLY AIR TOTAL COOLING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE IDEAL LOADS SUPPLY AIR TOTAL HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE PACKAGED TERMINAL HEAT PUMP TOTAL COOLING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE PACKAGED TERMINAL HEAT PUMP TOTAL HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=CHILLER ELECTRIC ENERGY, Frequency=Hourly
************* Key=*, VarName=BOILER HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=FAN ELECTRIC ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE IDEAL LOADS SUPPLY AIR LATENT HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE IDEAL LOADS SUPPLY AIR LATENT COOLING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE IDEAL LOADS SUPPLY AIR SENSIBLE HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE IDEAL LOADS SUPPLY AIR SENSIBLE COOLING ENERGY, Frequency=Hourly
************* Key=*, VarName=SYSTEM NODE MASS FLOW RATE, Frequency=Hourly
************* Key=*, VarName=SYSTEM NODE TEMPERATURE, Frequency=Hourly
************* Key=*, VarName=SYSTEM NODE RELATIVE HUMIDITY, Frequency=Hourly
************* There are 3 unused schedules in input.
************* There are 5 unused week schedules in input.
************* There are 13 unused day schedules in input.
************* Use Output:Diagnostics,DisplayUnusedSchedules; to see them.
*************
************* ===== Recurring Surface Error Summary =====
************* The following surface error messages occurred.
*************
************* Base Surface does not surround subsurface errors occuring...
************* Check that the GlobalGeometryRules object is expressing the proper starting corner and direction [CounterClockwise/Clockwise]
*************
** Warning ** Base surface does not surround subsurface (CHKSBS), Overlap Status=No-Overlap
** ~~~ ** The base surround errors occurred 1 times.
** ~~~ ** Surface "839A5ADACCE44BC0AF00_GLZP_31" misses SubSurface "839A5ADACCE44BC0AF00_GLZP_31_GLZ_31"
** Warning ** Base surface does not surround subsurface (CHKSBS), Overlap Status=Partial-Overlap
** ~~~ ** The base surround errors occurred 1 times.
** ~~~ ** Surface "839A5ADACCE44BC0AF00_GLZP_34" overlaps SubSurface "839A5ADACCE44BC0AF00_GLZP_34_GLZ_34"
*************
** ~~~ ** The base surround errors occurred 2 times (total).
*************
************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
************* EnergyPlus Sizing Error Summary. During Sizing: 2 Warning; 0 Severe Errors.
************* EnergyPlus Completed Successfully-- 7 Warning; 0 Severe Errors; Elapsed Time=00hr 07min 35.94sec…
rring to the above image)
Area
effective
effective
Second
Elastic
Elastic
Plastic
Radius
Second
Elastic
Plastic
Radius
of
Vy shear
Vz shear
Moment
Modulus
Modulus
Modulus
of
Moment
Modulus
Modulus
of
Section
Area
Area
of Area
upper
lower
Gyration
of Area
Gyration
(strong axis)
(strong axis)
(strong axis)
(strong axis)
(strong axis)
(weak axis)
(weak axis)
(weak axis)
(weak axis)
A
Ay
Az
Iy
Wy
Wy
Wply
i_y
Iz
Wz
Wplz
i_z
cm2
cm2
cm2
cm4
cm3
cm3
cm3
cm
cm4
cm3
cm3
cm
I have a very similar table which I could import to the Karamba table. But I have i_v or i_u values as well as radius of inertia for instance.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
dimensjon
Masse
Areal
akse
Ix
Wpx
ix
akse
Iy
Wpy
iy
akse
Iv
Wpv
iv
Width
Thickness
Radius R
[kg/m]
[mm2]
[mm4]
[mm3]
[mm]
[mm4]
[mm3]
[mm]
[mm4]
[mm3]
[mm]
[mm]
[mm]
[mm]
L 20x3
0.89
113
x-x
4,000
290
5.9
y-y
4,000
290
5.9
v-v
1,700
200
3.9
20
3
4
L 20x4
1.15
146
x-x
5,000
360
5.8
y-y
5,000
360
5.8
v-v
2,200
240
3.8
20
4
4
L 25x3
1.12
143
x-x
8,200
460
7.6
y-y
8,200
460
7.6
v-v
3,400
330
4.9
25
3
4
L 25x4
1.46
186
x-x
10,300
590
7.4
y-y
10,300
590
7.4
v-v
4,300
400
4.8
25
4
4
L 30x3
1.37
175
x-x
14,600
680
9.1
y-y
14,600
680
9.1
v-v
6,100
510
5.9
30
3
5
L 30x4
1.79
228
x-x
18,400
870
9.0
y-y
18,400
870
9.0
v-v
7,700
620
5.8
30
4
5
L 36x3
1.66
211
x-x
25,800
990
11.1
y-y
25,800
990
11.1
v-v
10,700
760
7.1
36
3
5
L 36x4
2.16
276
x-x
32,900
1,280
10.9
y-y
32,900
1,280
10.9
v-v
13,700
930
7.0
36
4
5
L 36x5
2.65
338
x-x
39,500
1,560
10.8
y-y
39,500
1,560
10.8
v-v
16,500
1,090
7.0
36
5
5
I have diagonals (bracings) which can buckle in these "non-regular" directions too, and they do. If I could add those values then in the Karamba model I could assign specific buckling scenarios..... I can see another challenge which will be at the ModifyElement component, I will not be able to choose these buckling lengths, in these directions.
Do you think this functionality can be added within short, or should I try to find another way to model these members?
Br, Balazs
…
nd linear/planar tectonics. Within this new field of investigation, the Stuttgart VS will be researching into novel techniques of material mixtures and grading, associative design and double curvature surface generation.
For the second cycle of this exploration we will be based at the Institute for Lightweight Structures and Conceptual Design (ILEK) at the University of Stuttgart. Drawing from the Institute’s long history of experimentation and research on tensile structures instigated by Frei Otto in the 1960s and conducted at present by Werner Sobek, this year we will be focusing on the design and fabrication of materially graded membranes, as well as the application of UHPC and FGC on fabric formworks. The workflow followed will be divided into two stages:
1. Computing Membranes: Computational form finding methods will be taught by professional engineers and architects from ILEK and str.ucture GmbH. The aim will be to utilise the latest software technologies to form find membranes for textile structures, or fabric formworks for complex concrete structures. The results will be evaluated against criteria such as internal air pressure, as well as asymmetric and wind loading. The outcome of this research will inform the material grading procedures (i.e. changing the stiffness, thickness or porosity of the membranes themselves, or the consistency of the concrete poured into the formworks) that will follow in stage two.
2. Fabricated Grading: The digitally computed membranes or formworks will eventually be fabricated physically, utilising the workshop and robotic fabrication facilities at ILEK. The objective will be to rethink conventional research on tensile and concrete structures as isotropic constructs, by customising attributes such as materiality, reinforcement, rigidity, translucency, patterning, and porosity among others. The final, graded prototypes will be made up of mixtures of materials, all accurately engineered to respond to variable environmental, structural and aesthetic criteria, in essence forming multi-material structures that have finally caught up with the latest material developments.
Prominent Features of the workshop/ skills developed:
Teaching team consisting of AA diploma tutors and ILEK and str.ucture GmbH engineers.
Access to the Institute of Lightweight Structures and Conceptual Design (ILEK), the Materials Testing Institute and Concrete Spraying Robotic facilities at the University of Stuttgart, as well as to the office of str.ucture GmbH Structural Design Engineering.
Computational skills tuition on Grasshopper, Rhino Membrane, and Karamba.
Lectures series by leading academics and practitioners in architecture and engineering.
Fabrication of functionally graded membrane and/or concrete structures.
Eligibility
The workshop is open to current architecture and design students, PhD candidates and young professionals. Software Requirements: Rhino (SR7 or later) and Grasshopper.
Fees
The AA Visiting School requires a student fee of £595 and a young professional fee of £895 per participant, which includes a £60 Visiting membership fee.
The deadline for applications is 10 July 2017.
For more information, please visit:
http://www.aaschool.ac.uk/STUDY/VISITING/stuttgart?name=stuttgart
For inquiries, please contact:
mixedmatters@aaschool.ac.uk…
mers considering extreme sports reject mainstream retailers and like to check out small stores rather of at chains plus malls. Several smaller retailers discuss trends in sports shoe sales. http://skateszone.com/
Though athletic shoes and sports stores and from doorways retailers have reported somewhat uptick in footwear sales due to the increase in extreme sports, the particular beneficiaries inside the trend are independent surf and skate niche stores.
Some West Coast surf and skate shops stated teenagers and even more youthful Generation Xers are not only rejecting traditional sports, but they're also shunning mainstream retailers and malls meant for smaller niche shops transporting hard-to-come-by brands.
Eddie Miyoshi, district manager at Atomic Garage, a 3-store chain situated in Gardena, Calif., stated the soaring recognition of skateboard footwear has boosted the retailer's total footwear business 20-thirty percent this year, rather of '95.
Skate footwear presently represent 80-90 % of Atomic Garage's shoe sales, while couple of years back, Dr. Martens and Timberland drove the retailer's footwear business.
Like many retailers, Miyoshi pointed to Airwalk since the trend's catalyst.
However, if Airwalk broadened its distribution to larger chains, which are frequently located in malls, only a few skate shoe customers adopted. Rather, many youthful males have switched for your skate shops for additional elusive brands like Etnies, Duffs, and Electricity Footwear by Circus. By refusing to market bigger retailers or sports stores, these brands are increasing their cachet among youthful consumers.
"Kids don't want stuff which have been within the shops,In . Miyoshi added.
Searching ahead, Miyoshi forecasted skate shoe sales will remain strong through spring '97 provided "the [hot] vendors don't auction other [non-particularly shop] retailers."
"Skaters and non-skaters are rebelling against mainstream retailers so on to surf and skate shops for many looks," echoed Mark Richards, co-online sources Val Surf, a 3-store chain situated in North Hollywood, Calif. Soaring sales of skate footwear have driven total footwear receipts up 25 percent this year rather of '95.
"The quantity of that increase might be connected while using exposure of maximum games? I am unsure. [Skate footwear] may also be actually the think about the moment,In . Richards acknowledged. And in relation to getting this right look, youthful customers can be very picky.
"Skateboard footwear is a huge category for people, but we're not able to own the brands, Etnies, Duffs, Electricity and Nice, simply because they won't sell us," stated Mark Anderson, buyer at Chick's Sports, a six-store chain in Covina, Calif. "We have people coming every single day requesting them." Consequently, skate footwear have consistently ongoing to obtain about 5 % of Chick's overall footwear business. http://skateszone.com/the-top-8-best-skateboards-for-beginners-reviews-2017/
Nonetheless, some outdoors, niche sports and sports retailers are noting the growing recognition and coverage of maximum sports will receive a modest impact on footwear sales. Trailrunning footwear and approach/outdoors crosstrainers will be the two groups benefiting the very best inside the recognition. Like the skate shoe business, some retailers realize that styling instead of function frequently drives sales of individuals footwear.
"At this time the merchandise is a lot more visual than function," stated Chet James, gm of Super Jock 'N Jill, Dallas, speaking about trailrunning footwear. Still, James noted the current hype over adventure sports helps draw more customer traffic. "The marketing campaigns and media help bring growing figures of people in, nonetheless they frequently occasions day an issue that increases results on their own account,Inch he conceded.
John Wilkinson, executive vp inside the 85-store chain Track 'N Trail, Eldorado Hillsides, Calif., stated the shop has "seen some activity in approach footwear," but he requested the amount of consumers depend in it commercially sport. And, instead of accelerating total footwear business, Wilkinson speculated elevated sales of approach footwear and trailrunners are gnawing away at traditional hiking shoe and boot volume.
But Dan Bazinet, president of Overland Exchanging, a 34-store chain situated in Westford, Mass., believes the company-new looks have breathed existence for the wilting hiking boot category. "[Approach-type footwear] don't represent the lion's participate the hiking market, nonetheless they have elevated the hiking business and provided us extra sales," Bazinet stated.
He designated Timberland's Treeline Series and Rockport's Leadville line as strong performers. Unsurprisingly, he noted the company-new looks are attractive to youthful consumer base than traditional hikers.
For that month of June, sales of men's hikers were up 49 percent at Overland, rather of June '95, while sales of women's hikers were up 17 % for that month. Bazinet also attributed elevated sales that shops walked inside the hiking business, departing that business for that specialists.
Some retailers draw a good example concerning the hiking boom of two yrs ago combined with the current extreme sport phenomenon. "Plenty of bigger chains will get a specific percent in the industry while [extreme] sports remain a fad because they are selling cost-point type gear," described Steven Carre, assistant hard goods buyer at Adventure 16, a six-store chain situated in Hillcrest.
"However individuals [true enthusiasts] will say `we need real gear' and may shown up at us. That will help us after a while. What Size Skateboard good for an 3 4 5 6 7 8 9 10 11 12 13 14 year old
…
nd improvements. Many of the new features and components announced in the last release have become stable and have emerged from their WIP section. Additionally, after two years of work, we are happy to announce that we finally have full support of an OpenStudio connection within Honeybee, which has ushered in a whole host of new features, notably the modelling of detailed HVAC systems. As always you can download the new release from Food4Rhino. Make sure to remove the older version of Ladybug and Honeybee and update your scripts.
LADYBUG
1 - Solar Hot Water Components Out of WIP
After much beta-testing, bug-fixing, and general development, all of the Photovoltaic and Solar Hot Water components are now fully out of WIP! The main component is based on a Chengchu Yan's publication. Components have been added to Ladybug thanks to the efforts of Chengchu Yan and Djordje Spasic.. See Djorje’s original release post of the solar hot water components for more information on the components that just made it out of WIP.
2 - New Terrain Shading Mask Released in WIP
In addition to Djordje’s prolific addition of renewable energy components, he has also contributed a widely-useful component to generate terrain shading masks, which account for the shading of surrounding mountains/terrain in simulations. While initially added to assist the solar radiation radiation and renewable energy components, the component will undergo development to optimize it for energy and daylight simulations over the next few months. Another new component called Horizon Angles can be used to visualize and export horizon angles. You can test them out now by accessing them in the WIP section. For more information, see Djordje’s release post on the GH forum here.
3 - New Mesh Selector Component
After realizing that the Optimal Shade Creator component has applications to a whole range of analyses, it has now been re-branded as the Mesh Selector and has been optimized to work easily with these many analyses. Specifically, the component selects out the portion of a mesh that meets a given threshold. This can be the portion of a shade benefit analysis meeting a certain level of shade desirability, the portion of a radiation study meeting a certain level of fulx, the portion of a daylight analysis meeting a certain lux threshold, and much more!
4 - Solar Adjusted Temperature Now Includes Long Wave Radiation
Thanks to a question asked by Aymeric and a number of clarifications made by Djordje Spasic, the Solar Adjusted Temperature component now includes the ability to account for long-wave radiative loss to the sky in addition to it original capability to account for short wave radiation from the sun. As such, the component now includes all capabilities of similar outdoor comfort tools such as RayMan. The addition of this capability is also paralleled by the addition of a new horizontalInfraredRadiation output on the ImportEPW component. See the updated solar adjusted example file hereto see how to use the component properly.
5 - Support for both Log and Power Law Wind Profiles
In preparation for the future release of the Butterfly CFD-modelling insect, the Ladybug Wind Profile component now includes the option of either power law or log law wind profiles, which are both used extensively in CFD studies. Thanks goes to Theodoros Galanos for providing the formulas!
6 - New Radiant Asymmetry Comfort Components
Prompted by a suggestion from Christian Kongsgaard, Ladybug now includes components to calculate radiant asymmetry discomfort! For examples of how to use the components see this example file for spatial analysis of radiant asymmetry discomfort and this example for temporal analysis.
7 - Pedestrian Wind Comfort Component Released in WIP
In preparation for the impending release of the butterfly CFD-modelling insect, Djordje Spasic with assistance from Liam Harrington has contributed a component to evaluate outdoor discomfort and pedestrian safety. The component identifies if certain areas around the building are suitable for sitting, building entrances-exits, window shopping... based on its wind microclimate. Dangerous areas due to high wind speeds are also identified.You can check it out now in the WIP section.
HONEYBEE
1 - New HVAC Systems and Full OpenStudio Support
After a significant amount of development on the part of the OpenStudio team and two years of effort on the part of LB+HB developers, we (finally!) have full support for an OpenStudio connection within Honeybee. By this, we mean that any energy simulation property that can be assigned to a HBZone will be taken into account in the simulation run by the OpenStudio component. The connection to OpenStudio has brought with it several new capabilities. Most notably, you can now assign full HVAC systems and receive energy results in units of electricity and fuel instead of simple heating and cooling loads. This Honeybee release includes 14 built-in HVAC template systems that can be assigned to the zones, each of which can be customized:
0. Ideal Air Loads 1. PTAC | Residential 2. PTHP | Residential 3. Packaged Single Zone - AC 4. Packaged Single Zone - HP 5. Packaged VAV w/ Reheat 6. Packaged VAV w/ PFP Boxes 7. VAV w/ Reheat 8. VAV w/ PFP Boxes 9. Warm Air Furnace - Gas Fired 10.Warm Air Furnace - Electric 11.Fan Coil Units + DOAS 12.Active Chilled Beams + DOAS 13.Radiant Floors + DOAS 14.VRF + DOAS
Systems 1-10 are ASHRAE Baseline systems that represent much of what has been added to building stock over the last few decades while systems 11-14 are systems that are commonly being installed today to reduce energy use. Here is an example file showing how to assign these systems in Honeybee and interpret the results and here is an example showing how to customize the HVAC system specifications to a wide variety of cases. To run the file, you will need to have OpenStudio installed and you can download and install OpenStudio from here.
In addition to these template systems within Honeybee, the OpenStudio interface includes hundreds of HVAC components to build your own custom HVAC systems. OpenStudio also has a growing number of user-contributed HVAC system templates that have been integrated into a set of scripts called "Measures" that you can apply to your OpenStudio model within the OpenStudio interface. You can find these system templates by searching for them in the building components library. Here is a good tutorial video on how to apply measures to your model within the OpenStudio interface. Honeybee includes a component that runs these measures from Grasshopper (without having to use the OpenStudio interface), which you can see a demo video of here. However, this component is currently in WIP as OpenStudio team is still tweaking the file structure of measures and it is fairly safe to estimate that, by the next stable release of Honeybee, we will have full support of OpenStudio measures within GH.
2 - Phasing Out IDF Exporter
With the connection to OpenStudio now fully established, this release marks the start of a transition away from exporting directly to EnergyPlus and the beginning of Honeybee development that capitalizes on OpenStudio’s development. As such THIS WILL BE THE LAST STABLE RELEASE THAT INCLUDES THE HONEYBEE_RUN ENERGY SIMULATION COMPONENT.
The Export to OpenStudio component currently does everything that the Run Energy Simulation component does and, as such, it is intended that all GH definitions using the Run Energy Simulation component should replace it with the OpenStudio component. You can use the same Read EP Result components to import the results from the OpenStudio component and you can also use the same Energy Sim Par/Generate EP Output components to customize the parameters of the simulation. The only effective difference between the two components is that the OpenStudio component enables the modeling of HVAC and exports the HBZones to an .osm file before converting it to an EnergyPlus .idf.
For the sake of complete clarity, we should state that OpenStudio is simply an interface for EnergyPlus and, as such, the same calculation engine is under the hood of both the Export to OpenStudio component and the Run Energy Simulation component. At present, you should get matching energy simulation results between the Run Energy Simulation component and a run of the same zones with the OpenStudio component (using an ideal air system HVAC).
All of this is to say that you should convert your GH definitions that use the Run Energy Simulation component to have the OpenStudio component and this release is the best time to do it (while the two components are supported equally). Additionally, with this version of Honeybee you will no longer need to install EnergyPlus before using Honeybee and you will only need to install OpenStudio (which includes EnergyPlus in the install).
3 - New Schedule Generation Components
Thanks to the efforts of Antonello Di Nunzio, we now have 2 new components that ease the creation of schedule-generation in Honeybee. The new components make use of the native Grasshopper “Gener Pool” component to give a set of sliders for each hour of the day. Additionally, Antonello has included an annual schedule component that contains a dictionary of all holidays of every nearly every nation (phew!). Finally, this annual schedule component can output schedules in the text format recognized by EnergyPlus, which allows them to be written directly into the IDF instead of a separate CSV file. This will significantly reduce the size of files needed to run simulations and can even reduce the number of components on your canvas that are needed to add custom schedules. For more information, see Antonello’s explanatory images here and Antonello's example file here. You can also see a full example file of how to apply the schedules to energy simulations here.
4 - EnergyPlus Lookup Folder, Re-run OSM/IDF, and Read Result Dictionary
With the new capabilities of OpenStudio, we have also added a number of components to assist with managing all of the files that you get from the simulation. In particular, Abraham Yezioro has added a Lookup EnergyPlus Folder component that functions very similarly to the Lookup Daylight Folder component. This way, you can run an Energy simulation once and explore the results separately. Furthermore, we have added components to Re-Run OpenStudio .osm files or EnergyPlus .idf files within Grasshopper. These components are particularly useful if you edit these .osm or .idf files outside of Honeybee and want to re-run them to analyze their results in Grasshopper. Lastly, a component has been added to parse the .rdd (or Result Data Dictionary) file that EnergyPlus produces, enabling you to see all of the possible outputs that you can request from a given simulation.
5 - Electric Lighting Components Out of WIP
After Sarith Subramaniam’s initial components to model electric lights with Radiance in the last release, we are happy to report that they have been fully tested and are out of WIP. Improvements include support for all types of light fixture geometries and the ability to use the components in a more “Grasshoppery” list-like fashion. See Sarith’s original release post for more information and several example files showing how to use the components can be found here. 1 , 2 , 3 .
6 - Improvements to THERM Components
A number of bug fixes and improvements have been made to the THERM components in order to make their application more flexible and smooth. Special thanks is due to Derin Yilmaz , Mel King , Farnaz , Ben (@benmo1) , and Abraham Yezioro for all of the great feedback in the process of improving these components.
7 - HBObject Transform Components
After some demand for components that can ease the generation of buildings with modular zone types, two components to transform HBObjects with all of their properties have been added to the 00 | Honeybee section. The components allow you to produce copies of zones that are translated or rotated from the original position.
8 - Comfort Maps Supports PET and Integration of CFD Results
Thanks to the addition of the ‘Physiological Equivalent Temperature’ (PET) component by Djordje Spasic in the last stable release, it is now possible to make comfort maps of PET with Honeybee. PET is particularly helpful for evaluating OUTDOOR comfort with detailed wind fields at a high spatial resolution. As such, the new PET recipe has also been optimized for integration with CFD results. The windSpeed_ input can now accept the file path to a .csv file that is organized with 8760 values in each column and a number of columns that correspond to the number of test points. Components to generate this csv from Butterfly CFD results will be coming in later releases. Stay tuned!
As always let us know your comments and suggestions.
Enjoy!Ladybug Analysis Tools Development Team
…
occur more than once in the same list, and different elements with identical values can occur more than once. Also, a list may contain lack of elements, referred to as "nulls".
Sets. Strictly speaking a Set is a mathematical construct which adheres to a strict collection of rules and limitations. Basically, a Set is the same as a List, with the exception that it cannot contain the same element more than once, or indeed two or more different elements with the same values. You see, in mathematics there is no difference between a value and an instance of that value, they are the same thing. In programming however it is possible to store the number 7 in more than one spot in the RAM. Grasshopper does not enforce this rule very strongly though, you can use a lot of Set components on lists that have multiple occurrences of the same value. The big difference between Lists and Sets in Grasshopper is that Sets are only defined for simple data types that have trivial equality comparisons. Basically: booleans, integers, numbers, complex numbers, strings, points, vectors, colours and intervals. Lists can contain all kinds of data.
Strings. Strings are text. There's nothing more to it. I don't know why early programmers chose to call them strings, but I suppose it's a better description of the memory representation of them. Strings are essentially sequences of individual characters.
Trees. Trees are the way all data is stored in Grasshopper. Even when you only have a single item, it will still be stored in a tree. A tree is a sorted collection of lists, where each list is identified by a path. A specific path can only occur once in a tree, when you merge two trees together, lists with identical paths are appended to each other. Trees are an attempt to losslessly represent not just the data itself, but also the history of that data. Imagine you have 4 curves {A,B,C,D} and you divide each into 3 points {X,Y,Z}. Then, for each of those points you create a new line segment {X',Y',Z'} and then divide each of those line segments again into 5 points each {K,L,M,N,O}. The way data is stored in trees, it should be possible to figure out whether a point M belongs to X' or to Z', and whether that X' or Z' came from A, B, C or D. This is why paths are often quite long after a while, because they encode a lot of history.
Paths. A Path is nothing more than a list of integers. It's denoted using curly brackets and semi-colons: {A;B;...;Z}. A Path should never be empty {} or have negative integers {0;-1}, but it is certainly possible to create a path like this and it probably won't even crash Grasshopper. Paths are 'grown' by components that (potentially) create more than one output value for a single input value. For example Divide Curve. It creates N points for every single input curve. In cases like this a new integer is appended to the end of the path.
In the next release the Path logic in Grasshopper is somewhat different. I fixed a number of obscure bugs (hopefully without introducing new fresh bugs) and special cased certain operations to somewhat reduce the speed at which paths grow. This may well break files that rely on a specific tree layout, but I hope the temporary sacrifice will be worth the long-term benefits.
--
David Rutten
david@mcneel.com
Poprad, Slovakia…
ion of both Ladybug and Honeybee. Notable among the new components are 51 new Honeybee components for setting up and running energy simulations and 15 new Ladybug components for running detailed comfort analyses. We are also happy to announce the start of comprehensive tutorial series on how to use the components and the first one on getting started with Ladybug can be found here:
https://www.youtube.com/playlist?list=PLruLh1AdY-Sj_XGz3kzHUoWmpWDXNep1O
A second one on how to use the new Ladybug comfort components can be found here:
https://www.youtube.com/playlist?list=PLruLh1AdY-Sho45_D4BV1HKcIz7oVmZ8v
Here is a short list highlighting some of the capabilities of this current Honeybee release:
1) Run EnergyPlus and OpenStudio Simulations - A couple of components to export your HBZones into IDF or OSM files and run energy simulations right from the grasshopper window! Also included are several components for adjusting the parameters of the simulations and requesting a wide range of possible outputs.
2) Assign EnergyPlus Constructions - A set of components that allow you to assign constructions from the OpenStudio library to your Honeybee objects. This also includes components for searching through the OpenStudio construction/material library and components to create your own constructions and materials.
3) Assign EnergyPlus Schedules and Loads - A set of components for assigning schedules and Loads from the Openstudio library to your Honeybee zones. This includes the ability to auto-assign these based on your program or to tweak individual values. You can even create your own schedules from a stream of 8760 values with the new “Create CSV Schedule” component. Lastly, there is a component for converting any E+ schedule to 8760 values, which you can then visualize with the standard Ladybug components
4) Assign HVAC Systems - A set of components for assigning some basic ASHRAE HVAC systems that can be run with the Export to OpenStudio component. You can even adjust the parameters of these systems right in Grasshopper.
Note: The ASHRAE systems are only available for OpenStudio and can’t be used with Honeybee’s EnergyPlus component. Also, only ideal air, VAV and PTHP systems are currently available but more will be on their way soon!
5) Import And Visualize EnergyPlus Results - A set of components to import numerical EnergyPlus simulation results back into grasshopper such that they can be visualized with any of the standard Ladybug components (ie. the 3D chart or Psychrometric chart). Importers are made for zone-level results as well as surface results and surfaces results can be easily separated based on surface type. This also means that E+ results can be analyzed with the new Ladybug comfort calculator components and used in shade or natural ventilation studies. Lastly, there are a set of components for coloring zone/surface geometry with EnergyPlus results and for coloring the shades around zones with shade desirability.
6) Increased Radiance and Daysim Capabilities - Several updates have also been made to the existing Radiance and Daysim components including parallel Radiance Image-based analysis.
7) Visualize HBObject Attributes - A few components have been added to assist with setting up honeybee objects and ensuing the the correct properties have been assigned. These include components to separate surfaces based on boundary condition and components to label surfaces and zones with virtually any of their EnergyPlus or Radiance attributes.
8) WIP Grizzly Bear gbxml Exporter - Lastly, the release includes an WIP version of the Grizzly Bear gbXML exporter, which will continue to be developed over the next few months.
And here’s a list of the new Ladybug capabilities:
1) Comfort Models - Three comfort models that have been translated to python for your use in GH: PMV, Adaptive, and Outdoor (UTCI). Each of these models has a “Comfort Calculator” component for which you can input parameters like temperature and wind speed to get out comfort metrics. These can be used in conjunction with EPW data or EnergyPlus results to calculate comfort for every hour of the year.
2) Ladybug Psychrometric Chart - A new interactive psychrometric chart that was made possible thanks to the releasing of the Berkely Center for the Built Environment Comfort Tool Code (https://github.com/CenterForTheBuiltEnvironment/comfort-tool). The new psychrometric chart allows you to move the comfort polygon around based on PMV comfort metrics, plot EPW or EnergyPlus results on the psych chart, and see how many hours are made comfortable in each case. The component also allows you to plot polygons representing passive building strategies (like internal heat gain or evaporative cooling), which will adjust dynamically with the comfort polygon and are based on the strategies included in Climate Consultant.
3) Solar Adjusted MRT and Outdoor Shade Evaluator - A component has been added to allow you to account for shortwave solar radiation in comfort studies by adjusting Mean Radiant Temperature. This adjusted MRT can then be factored into outdoor comfort studies and used with an new Ladybug Comfort Shade Benefit Evaluator to design outdoor shades and awnings.
4) Wind Speed - Two new components for visualizing wind profile curves and calculating wind speed at particular heights. These allow users to translate EPW wind speed from the meteorological station to the terrain type and height above ground for their site. They will also help inform the CFD simulations that will be coming in later releases.
5) Sky Color Visualizer - A component has been added that allows you to visualize a clear sky for any hour of the year in order to get a sense of the sky qualities and understand light conditions in periods before or after sunset.
Ready to Start?
Here is what you will need to do:
Download Honeybee and Ladybug from the same link here. Make sure that you remove any old version of Ladybug and Honeybee if you have one, as mentioned on the Ladybug group page.
You will also need to install RADIANCE, DAYSIM and ENERGYPLUS on your system. We already sent a video about how to get RADIANCE and Daysim installed (link). You can download EnergyPlus 8.1 for Windows from the DOE website (http://apps1.eere.energy.gov/buildings/energyplus/?utm_source=EnergyPlus&utm_medium=redirect&utm_campaign=EnergyPlus%2Bredirect%2B1).
“EnergyPlus is a whole building energy simulation program that engineers, architects, and researchers use to model energy and water use in buildings.”
“OpenStudio is a cross-platform (Windows, Mac, and Linux) collection of software tools to support whole building energy modeling using EnergyPlus and advanced daylight analysis using Radiance.”
Make sure that you install ENERGYPLUS in a folder with no spaces in the file path (e.g. “C:\Program Files” has a space between “Program” and “Files”). A good option for each is C:\EnergyPlusV8-1-0, which is usually the default locations when you run the downloaded installer.
New Example Files!
We have put together a large number of new updated example files and you should use these to get yourself started. You can download them from the link on the group page.
New Developers:
Since the last release, we have had several new members join the Ladybug + Honeybee developer team:
Chien Si Harriman - Chien Si has contributed a large amount of code and new components in the OpenStudio workflow including components to add ASHRAE HVAC systems into your energy models and adjust their parameters. He is also the author of the Grizzly Bear gbxml exporter and will be continuing work on this in the following months.
Trygve Wastvedt - Trygve has contributed a core set of functions that were used to make the new Ladybug Colored Sky Visualizer and have also helped sync the Ladybug Sunpath to give sun positions for the current year of 2014
Abraham Yezioro - Abraham has contributed an awesome new bioclimatic chart for comfort analyses, which, despite its presence in the WIP tab, is nearly complete!
Djordje Spasic - Djordje has contributed a number of core functions that were used to make the new Ladybug Wind Speed Calculator and Wind Profile Visualizer components and will be assisting with workflows to process CFD results in the future. He also has some more outdoor comfort metrics in the works.
Andrew Heumann - Andrew contributed an endlessly useful list item selector, which can adjust based on the input list, and has multiple applications throughout Ladybug and Honeybee. One of the best is for selecting zone-level programs after selecting an overall building program.
Alex Jacobson - Alex also assisted with the coding of the wind speed components.
And, as always, a special thanks goes to all of our awesome users who tested the new components through their several iterations. Special thanks goes to Daniel, Michal, Francisco, and Agus for their continuous support. Thanks again for all the support, great suggestions and comments. We really cannot thank you enough.
Enjoy!,
Ladybug + Honeybee Development Team
PS: If you want to be updated about the news about Ladybug and Honeybee like Ladybug’s Facebook page (https://www.facebook.com/LadyBugforGrasshopper) or follow ladybug’s twitter account (@ladybug_tool).
…