the loops haven't even started yet. This is a one time overhead - re-starting the loops after that doesn't have this long delay until you close and re-open the file.
Second, I got some encouraging results rather quickly but then spent WAY TOO MUCH TIME trying to replace the inner loop with a "Fast Loop". These are not well behaved in the sense that they don't respond to <ESC> like the "Classic" loops do so you can't stop them; and I never got the same results as the "Classic", no matter what I tried - but ultimately, I just got too frustrated with "Fast Loop" causing Rhino/GH and my whole laptop to freeze up - VERY BAD!!!!!!!!!!
I re-wired the loops slightly so that the hour used by your 'analysisPeriod' cluster is determined by the 'D0' value inside the inner loop.
I added a "Loop On / Loop Off" switch to stop/start the looping (which was useless with "Fast Loop" - grrr....).
I 'Simplified' the 'D1' output of the inner loop and enabled 'Record data' and 'Output after the last' on the outer loop.
And I got this - four buildings over three hours takes about 20 seconds:
Eleven buildings over three hours takes about one minute.
I'm not sure what will happen when I increase the hours and number of buildings but will try it when I have more time. It might be a good idea to avoid writing to Excel inside the loops and wait for the end results before writing them to an Excel file?
There are more possibilities for re-wiring based on simplifying various outputs but I'm tired of this for now and have other things to do. The exponential slowdown you observed might be due in part to Anemone adding an extra branch path every time it loops; adding 'Simplify' might help this?
P.S. 11 buildings over 13 hours (6am to 6pm) took 5 minutes 38 seconds.…
Added by Joseph Oster at 12:54pm on January 18, 2016
ells new products like the Firefly Interactive Prototyping Shield which mounts on top of your Arduino Uno and provides access to a number of useful input (ie. sensors) and output (ie. motors) devices. It includes features like:
Three linear slide potentiometers connected to analog pins 0, 1, and 2
Two-axis joystick connected to analog pins 3 and 4
Light sensor (photocell) connected to analog pin 5
Three push buttons connected to digital pins 2, 4, and 7
Red LED connected to digital pin 13
RGB LED connected to digital pins 3, 5, and 6
Two servo connections on digital pins 8 and 9
A connection to the Easy Stepper Driver (co-designed by Sparkfun Electronics and Brian Schmalz) to control stepper motors. The direction of the motor is controlled through digital pin 10 and the number of steps through digital pin 12
High-voltage MOSFET circuit capable of driving lights, valves, DC motors, solenoids, or anything else requiring higher voltage or current. The gate of the MOSFET is connected to digital pin 11 (PWM).
Some come take a look and let us know what you think!
…
A repository of generic or complex examples.
Example 01: Attractor Values
ND_001_AttractorValues.gh
Example 02: Curve Values
ND_002_CurveValues.gh
Example 03: Point Attractor
ND_003_PointAttract
hange to a rectangle or a sequence of lines to get the tube geometry. Author of the video explained how to do this in the comments, but that didn't help. :(
"Alan Rodriguez Carrillo 1 year ago + Aldo Villanueva Hi, what you can do is try to handle points (4) with the ListITEM component and change the order of relation, for example (0,1) (1,2) (2,3) (3, 4) (4.0) in a panel. Subsequently do the relation of points through a line from points or LineSDL and elaborate the same steps that are explained in this video. Thanks.
Carlos González Puchol 11 months ago + Aldo Villanueva + Alan Rodríguez Carrillo Buenas, Alan and Aldo. I made a closed, tube design. First I listed the 4 points and put them in order with the polyline the polyline, making it closed. Then I had to close them also in the last steps before doing the triangulation."
Can anyone explain how to make this work ? It seems easy. For a person that knows the trick :))
https://www.dropbox.com/s/9dnyfoielum6m1r/PABELLON_last.3dm?dl=0 https://www.dropbox.com/s/y8xdiaf66xbyn9l/PAVILION.gh?dl=0…
ly 26-27-28-29 (digital fabrication)
The third edition of digitalMed Workshop is structured as a design laboratory. Participants will learn the challenging process of producing ideas, projects and research analysis that are to be developed through specific software and concepts that emerge through the use of mapping, parametric design and digital fabrication.
The workshop will take place in the city of Salerno (Italy) and it will last 11 days structured into 3 intensive weekends: July 13-14-15 (mapping); July 19-20-21-22 (parametric design); July 26-27-28-29 (digital fabrication).
Goals and Objectives:
We aim to make clear the theoretical and technical knowledge in the approach to parametric and generative design and digital fabrication. (From collection and data management, to the manner in which these inform the geometries, to the fabrication of prototypes.)
Participants will also have the opportunity to practice the new knowledge gained in the design laboratory through project work.
Project Theme:
"Urban Field" Identify, study and analyze the system of public spaces in the urban area of the city of Salerno.
Connection, mutation, generation and evolution are the themes to be followed in project work.
Brief Description of Topics:
- Mapping. Our reality, in all its forms, has studied through concepts of the theory of Complex Systems. The techniques that will be used to study events and places of reality, will work for the management, manipulation and visualization of data and information. These will form the basis for project management and driven geometry, conducted during the second phase of the workshop.
- Parametric Design. Introduction to Rhino* and Grasshopper. Specifically, we will explain the concepts with which to work with the software of parametric design and how they function. Through these tools, we will arrive at the definition of systems of mathematical and / or geometrical relationships that are able to generate and govern patterns, shapes and objects that will inform the final design.
- Digital Fabrication. In this phase, participants of the workshop are organized into working groups. Participants have access to materials and conceptual apparatus that will take them directly to the fabrication of the geometries of the project, with the use of software CAD / CAM interface and the use of machines for the digital fabrication.
The DigitalMed workshop is organized by Nomad AREA (Academy of Research & Training in topics of Contemporary Architecture), in collaboration with the City of Salerno, the Order of Architects Province of Salerno and the National Institute of Architecture In / Arch - Campania.
Interested parties may download the Notice of Competition at the address www.digitalmedworkshop.com and fill the pre-registration no later than July 10th 2012.
PRESS OFFICE
Dr. Francesca Luciano
328 61 20 830
fra_luciano@libero.it
For information or subscriptions:
e-mail: info@digitalmedworkshop.com - tel: 089 463126 - 3391542980 …
8.3.0 ************* IDF Context for following error/warning message: ************* Note -- lines truncated at 300 characters, if necessary... ************* 829 Construction, ************* indicated Name=PELLE001 ************* Only last 10 lines before error line shown.....
************* 832 AIR WALL2, !- - Layer 2 ************* 833 X-LAM, !- - Layer 3 ************* 834 POLYSTYRENE2, !- - Layer 4 ************* 835 PANNELLO VIP, !- - Layer 5 ************* 836 POLYSTYRENE2, !- - Layer 6 ************* 837 X-LAM, !- - Layer 7 ************* 838 LANA DI ROCCIAS, !- - Layer 8 ************* 839 VANO IMPIANTI, !- - Layer 9 ************* 840 LANA DI ROCCIAS, !- - Layer 10 ************* 841 LASTRA IN GESSOFIBRA, !- - Layer 11 ** Severe ** IP: IDF line~841 Error detected for Object=CONSTRUCTION ** ~~~ ** Maximum arguments reached for this object, trying to process ->LASTRA IN GESSOFIBRA<- ************* IDF Context for following error/warning message: ************* Note -- lines truncated at 300 characters, if necessary... ************* 985 Construction, ************* indicated Name=ROOF001 ************* Only last 10 lines before error line shown..... ************* 988 TRAVETTI, !- - Layer 2 ************* 989 TAVOLATO, !- - Layer 3 ************* 990 POLYSTYRENE2, !- - Layer 4 ************* 991 PANNELLO VIP, !- - Layer 5 ************* 992 POLYSTYRENE2, !- - Layer 6 ************* 993 X-LAM, !- - Layer 7 ************* 994 LANA DI ROCCIAS, !- - Layer 8 ************* 995 VANO IMPIANTI, !- - Layer 9 ************* 996 LANA DI ROCCIAS, !- - Layer 10 ************* 997 LASTRA IN GESSOFIBRA, !- - Layer 11 ** Severe ** IP: IDF line~997 Error detected for Object=CONSTRUCTION ** ~~~ ** Maximum arguments reached for this object, trying to process ->LASTRA IN GESSOFIBRA<- ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details. ** Severe ** IP: Possible incorrect IDD File ** ~~~ ** IDD Version:"IDD_Version 8.3.0" ** ~~~ ** Version in IDF="8.3" not the same as expected="8.3" ** ~~~ ** Possible Invalid Numerics or other problems ** Fatal ** IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination. ...Summary of Errors that led to program termination: ..... Reference severe error count=3 ..... Last severe error=IP: Possible incorrect IDD File ************* Warning: Node connection errors not checked - most system input has not been read (see previous warning). ************* Fatal error -- final processing. Program exited before simulations began. See previous error messages. ************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors. ************* EnergyPlus Sizing Error Summary. During Sizing: 0 Warning; 0 Severe Errors. ************* EnergyPlus Terminated--Fatal Error Detected. 1 Warning; 3 Severe Errors; Elapsed Time=00hr 00min 0.34sec
My question is how i can fix it ??? and why it tell me that:
** Severe ** IP: Possible incorrect IDD File** ~~~ ** IDD Version:"IDD_Version 8.3.0"** ~~~ ** Version in IDF="8.3" not the same as expected="8.3"** ~~~ ** Possible Invalid Numerics or other problems** Fatal ** IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination....Summary of Errors that led to program termination:
Help me pleaseeeeeeee
Happy new year!!!!!…
8.3.0************* IDF Context for following error/warning message:************* Note -- lines truncated at 300 characters, if necessary...************* 829 Construction,************* indicated Name=PELLE001************* Only last 10 lines before error line shown.....
************* 832 AIR WALL2, !- - Layer 2************* 833 X-LAM, !- - Layer 3************* 834 POLYSTYRENE2, !- - Layer 4************* 835 PANNELLO VIP, !- - Layer 5************* 836 POLYSTYRENE2, !- - Layer 6************* 837 X-LAM, !- - Layer 7************* 838 LANA DI ROCCIAS, !- - Layer 8************* 839 VANO IMPIANTI, !- - Layer 9************* 840 LANA DI ROCCIAS, !- - Layer 10************* 841 LASTRA IN GESSOFIBRA, !- - Layer 11** Severe ** IP: IDF line~841 Error detected for Object=CONSTRUCTION** ~~~ ** Maximum arguments reached for this object, trying to process ->LASTRA IN GESSOFIBRA<-************* IDF Context for following error/warning message:************* Note -- lines truncated at 300 characters, if necessary...************* 985 Construction,************* indicated Name=ROOF001************* Only last 10 lines before error line shown.....************* 988 TRAVETTI, !- - Layer 2************* 989 TAVOLATO, !- - Layer 3************* 990 POLYSTYRENE2, !- - Layer 4************* 991 PANNELLO VIP, !- - Layer 5************* 992 POLYSTYRENE2, !- - Layer 6************* 993 X-LAM, !- - Layer 7************* 994 LANA DI ROCCIAS, !- - Layer 8************* 995 VANO IMPIANTI, !- - Layer 9************* 996 LANA DI ROCCIAS, !- - Layer 10************* 997 LASTRA IN GESSOFIBRA, !- - Layer 11** Severe ** IP: IDF line~997 Error detected for Object=CONSTRUCTION** ~~~ ** Maximum arguments reached for this object, trying to process ->LASTRA IN GESSOFIBRA<-** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.** Severe ** IP: Possible incorrect IDD File** ~~~ ** IDD Version:"IDD_Version 8.3.0"** ~~~ ** Version in IDF="8.3" not the same as expected="8.3"** ~~~ ** Possible Invalid Numerics or other problems** Fatal ** IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination....Summary of Errors that led to program termination:..... Reference severe error count=3..... Last severe error=IP: Possible incorrect IDD File************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.************* EnergyPlus Sizing Error Summary. During Sizing: 0 Warning; 0 Severe Errors.************* EnergyPlus Terminated--Fatal Error Detected. 1 Warning; 3 Severe Errors; Elapsed Time=00hr 00min 0.34sec
My question is how i can fix it ??? and why it tell me that:
** Severe ** IP: Possible incorrect IDD File** ~~~ ** IDD Version:"IDD_Version 8.3.0"** ~~~ ** Version in IDF="8.3" not the same as expected="8.3"** ~~~ ** Possible Invalid Numerics or other problems** Fatal ** IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination....Summary of Errors that led to program termination:
Help me pleaseeeeeeee
Thanks and Happy new year!!!!!…
s the "Surface Populating" definition: I manage to populate my geometry over the surface, but after I bake it, I have to delete the boxes that define my components limits as well! Is there any way of populating and baking only the chosen component, without having to delete the boxes afterwards?
Secondly:
Basically: I am trying to cover a surface with two types of components [ an open one and a closed one] , which will be proliferated over my tubular surface according to the main sunlight direction.
1. I introduce the surface component.
2. I use "Divide Interval2" in order to have division into U and V.
3. i generate the target boxes [ "surfaceBox"] .
4. I use "Isotrim" ( same intervals) and "BRepArea" to find centroid of each area.
5. My "Curve" component introduces sun angle, with its "End Points".
6. I use "Vector 2Pt" to specify sun-light direction.
7. I want to measure the angle between sun-light and the surface normals, at the position of each component; after generating the centre points, I need the normals of each centre point to get the surface's points' UV, and "Evaluate" the srf at points.
8."Angle" and "Vector" components: I use them in order to evaluate the angle between the sun direction and the srf.
9. I convert this angle to degree by using a "Function" [ to see if the angle is bigger from the max.angle or not...]
10. Function "x,y" gives me boolean data.
11. Data become "Dispatch"ed...
12. Two "Morph" components , each one linked to one part of the "Dispatch" data, generate "closed" and "open" components over the srf.
The result should have been different types of components, based on the surface's curvature, diraction and sun-light direction...
I do not understand where the mistake is in this definition...
Thx in advance1
Spyros K.…
r [String Split] in version 0.9.0014)
The [Timer] prompts a component to up date at the set interval. in this case every 1 seconds.
The [Time] param is a placeholder for a time in the same way that a [Number] param can hold real numbers.
By using "Now" as the input to the [Time] param you will get the current time when the param updates. therefore every second it resets to the current time.
The [Text Split] is there to separate the output of [Time] in a string format at every colon ":"
Therefore "Monday, 13-MAY-2013 (11:23:30)" would become:
0 Monday, 13-MAY-2013 (1
1 23
2 30)
The next two components use this to convert it into the current seconds. Because we are after the last item "30)" we can use [List Item] on a reversed list to get the last item.
Now we have to remove the ")" with [Replace String] but we are replacing it with nothing so it disappears.
The Arrow is part of the Sketch Tool Functionality of the canvas.
Lastly the 3 different inputs should go into the three different Inputs of the [Stream Filter]
…
.0004. [1 of 7] Writing simulation parameters...5. [2 of 6] No context surfaces...6. [3 of 6] Writing geometry...7. [4 of 6] Writing materials and constructions...8. [5 of 7] Writing schedules...9. [6 of 7] Writing loads and ideal air system...10. [7 of 7] Writing outputs...11. ...... idf file is successfully written to : c:\ladybug\unnamed\EnergyPlus\unnamed.idf12. 13. Analysis is running!...14. c:\ladybug\unnamed\EnergyPlus\eplusout.csv15. ......
Done! Read below for errors and warnings:
16. 17. Program Version,EnergyPlus, Version 8.2.7-777c1f8d79, YMD=2015.02.28 16:09,IDD_Version 8.2.718. 19. ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.20. 21. ** Warning ** Version: in IDF="'8.2.7'" not the same as expected="8.2"22. 23. ** Warning ** ManageSizing: For a zone sizing run, there must be at least 1 Sizing:Zone input object. SimulationControl Zone Sizing option ignored.24. 25. ** Warning ** ManageSizing: For a plant sizing run, there must be at least 1 Sizing:Plant object input. SimulationControl Plant Sizing option ignored.26. 27. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=F73533B3C6894C67936B_GLZP_1228. 29. ** ~~~ ** Opening Surface creating error=F73533B3C6894C67936B_GLZP_12_GLZ_1230. 31. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=F73533B3C6894C67936B_GLZP_2532. 33. ** ~~~ ** Opening Surface creating error=F73533B3C6894C67936B_GLZP_25_GLZ_2534. 35. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=F73533B3C6894C67936B_GLZP_2836. 37. ** ~~~ ** Opening Surface creating error=F73533B3C6894C67936B_GLZP_28_GLZ_2838. 39. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=4BDFD67E6D0E486796CC_GLZP_940. 41. ** ~~~ ** Opening Surface creating error=4BDFD67E6D0E486796CC_GLZP_9_GLZ_942. 43. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=4BDFD67E6D0E486796CC_GLZP_1044. 45. ** ~~~ ** Opening Surface creating error=4BDFD67E6D0E486796CC_GLZP_10_GLZ_1046. 47. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=4BDFD67E6D0E486796CC_GLZP_1148. 49. ** ~~~ ** Opening Surface creating error=4BDFD67E6D0E486796CC_GLZP_11_GLZ_1150. 51. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=4BDFD67E6D0E486796CC_GLZP_1552. 53. ** ~~~ ** Opening Surface creating error=4BDFD67E6D0E486796CC_GLZP_15_GLZ_1554. 55. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=4BDFD67E6D0E486796CC_GLZP_2456. 57. ** ~~~ ** Opening Surface creating error=4BDFD67E6D0E486796CC_GLZP_24_GLZ_2458. 59. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=4BDFD67E6D0E486796CC_GLZP_2560. 61. ** ~~~ ** Opening Surface creating error=4BDFD67E6D0E486796CC_GLZP_25_GLZ_2562. 63. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=4BDFD67E6D0E486796CC_GLZP_3064. 65. ** ~~~ ** Opening Surface creating error=4BDFD67E6D0E486796CC_GLZP_30_GLZ_3066. 67. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=4BDFD67E6D0E486796CC_GLZP_3268. 69. ** ~~~ ** Opening Surface creating error=4BDFD67E6D0E486796CC_GLZP_32_GLZ_3270. 71. ** Severe ** GetHTSubSurfaceData: Surface Openings have too much area for base surface=4BDFD67E6D0E486796CC_GLZP_3472. 73. ** ~~~ ** Opening Surface creating error=4BDFD67E6D0E486796CC_GLZP_34_GLZ_3474. 75. ** Warning ** GetSurfaceData: Very small surface area[2.94495E-004], Surface=F73533B3C6894C67936B_GLZP_076. 77. ** Warning ** GetSurfaceData: Very small surface area[3.84753E-004], Surface=F73533B3C6894C67936B_GLZP_178. 79. ** Warning ** GetSurfaceData: Very small surface area[9.16905E-004], Surface=F73533B3C6894C67936B_GLZP_380. 81. ** Warning ** GetSurfaceData: Very small surface area[4.96186E-004], Surface=F73533B3C6894C67936B_GLZP_482. 83. ** Warning ** GetSurfaceData: Very small surface area[2.37373E-005], Surface=F73533B3C6894C67936B_GLZP_684. 85. ** Warning ** GetSurfaceData: Very small surface area[6.35824E-004], Surface=F73533B3C6894C67936B_GLZP_786. 87. ** Warning ** GetSurfaceData: Very small surface area[5.86549E-004], Surface=F73533B3C6894C67936B_GLZP_888. 89. ** Warning ** GetSurfaceData: Very small surface area[7.63765E-004], Surface=F73533B3C6894C67936B_GLZP_1090. 91. ** Severe ** GetSurfaceData: Zero or negative surface area[-8.09566E-004], Surface=F73533B3C6894C67936B_GLZP_1292. 93. ** Warning ** GetSurfaceData: Very small surface area[1.51701E-004], Surface=F73533B3C6894C67936B_GLZP_1394. 95. ** Warning ** GetSurfaceData: Very small surface area[9.29917E-004], Surface=F73533B3C6894C67936B_GLZP_1596. 97. ** Warning ** GetSurfaceData: Very small surface area[2.94451E-004], Surface=F73533B3C6894C67936B_GLZP_1698. 99. ** Warning ** GetSurfaceData: Very small surface area[8.03294E-004], Surface=F73533B3C6894C67936B_GLZP_17100. 101. ** Warning ** GetSurfaceData: Very small surface area[6.83026E-004], Surface=F73533B3C6894C67936B_GLZP_18102. 103. ** Warning ** GetSurfaceData: Very small surface area[9.29917E-004], Surface=F73533B3C6894C67936B_GLZP_20104. 105. ** Warning ** GetSurfaceData: Very small surface area[3.19851E-005], Surface=F73533B3C6894C67936B_GLZP_21106. 107. ** Warning ** GetSurfaceData: Very small surface area[7.63765E-004], Surface=F73533B3C6894C67936B_GLZP_23108. 109. ** Severe ** GetSurfaceData: Zero or negative surface area[-4.05899E-004], Surface=F73533B3C6894C67936B_GLZP_25110. 111. ** Warning ** GetSurfaceData: Very small surface area[6.35824E-004], Surface=F73533B3C6894C67936B_GLZP_27112. 113. ** Severe ** GetSurfaceData: Zero or negative surface area[-9.91146E-004], Surface=F73533B3C6894C67936B_GLZP_28114. 115. ** Warning ** GetSurfaceData: Very small surface area[2.70158E-004], Surface=F73533B3C6894C67936B_GLZP_29116. 117. ** Warning ** GetSurfaceData: Very small surface area[3.22781E-004], Surface=F73533B3C6894C67936B_GLZP_30118. 119. ** Warning ** GetSurfaceData: Very small surface area[4.67821E-004], Surface=F73533B3C6894C67936B_GLZP_33120. 121. ** Warning ** GetSurfaceData: Very small surface area[3.22737E-004], Surface=F73533B3C6894C67936B_GLZP_34122. 123. ** Warning ** GetSurfaceData: Very small surface area[2.65634E-004], Surface=4BDFD67E6D0E486796CC_GLZP_0124. 125. ** Warning ** GetSurfaceData: Very small surface area[4.70736E-004], Surface=4BDFD67E6D0E486796CC_GLZP_1126. 127. ** Warning ** GetSurfaceData: Very small surface area[3.42507E-004], Surface=4BDFD67E6D0E486796CC_GLZP_3128. 129. ** Warning ** GetSurfaceData: Very small surface area[5.89276E-004], Surface=4BDFD67E6D0E486796CC_GLZP_4130. 131. ** Warning ** GetSurfaceData: Very small surface area[1.91146E-004], Surface=4BDFD67E6D0E486796CC_GLZP_6132. 133. ** Warning ** GetSurfaceData: Very small surface area[9.71205E-004], Surface=4BDFD67E6D0E486796CC_GLZP_7134. 135. ** Warning ** GetSurfaceData: Very small surface area[4.34494E-004], Surface=4BDFD67E6D0E486796CC_GLZP_8136. 137. ** Severe ** GetSurfaceData: Zero or negative surface area[-3.60159E-004], Surface=4BDFD67E6D0E486796CC_GLZP_9138. 139. ** Severe ** GetSurfaceData: Zero or negative surface area[-1.11946E-004], Surface=4BDFD67E6D0E486796CC_GLZP_10140. 141. ** Severe ** GetSurfaceData: Zero or negative surface area[-3.41257E-004], Surface=4BDFD67E6D0E486796CC_GLZP_11142. 143. ** Severe ** GetSurfaceData: Zero or negative surface area[-8.21483E-005], Surface=4BDFD67E6D0E486796CC_GLZP_15144. 145. ** Warning ** GetSurfaceData: Very small surface area[2.65716E-004], Surface=4BDFD67E6D0E486796CC_GLZP_16146. 147. ** Warning ** GetSurfaceData: Very small surface area[4.84044E-004], Surface=4BDFD67E6D0E486796CC_GLZP_17148. 149. ** Warning ** GetSurfaceData: Very small surface area[7.12297E-004], Surface=4BDFD67E6D0E486796CC_GLZP_19150. 151. ** Warning ** GetSurfaceData: Very small surface area[6.14324E-004], Surface=4BDFD67E6D0E486796CC_GLZP_22152. 153. ** Warning ** GetSurfaceData: Very small surface area[8.88887E-004], Surface=4BDFD67E6D0E486796CC_GLZP_23154. 155. ** Severe ** GetSurfaceData: Zero or negative surface area[-9.89060E-004], Surface=4BDFD67E6D0E486796CC_GLZP_24156. 157. ** Severe ** GetSurfaceData: Zero or negative surface area[-1.14849E-003], Surface=4BDFD67E6D0E486796CC_GLZP_25158. 159. ** Warning ** GetSurfaceData: Very small surface area[4.00479E-004], Surface=4BDFD67E6D0E486796CC_GLZP_27160. 161. ** Warning ** GetSurfaceData: Very small surface area[6.63061E-005], Surface=4BDFD67E6D0E486796CC_GLZP_28162. 163. ** Warning ** GetSurfaceData: Very small surface area[1.09018E-004], Surface=4BDFD67E6D0E486796CC_GLZP_29164. 165. ** Severe ** GetSurfaceData: Zero or negative surface area[-2.49326E-005], Surface=4BDFD67E6D0E486796CC_GLZP_30166. 167. ** Severe ** GetSurfaceData: Zero or negative surface area[-3.17446E-004], Surface=4BDFD67E6D0E486796CC_GLZP_32168. 169. ** Warning ** GetSurfaceData: Very small surface area[8.60686E-004], Surface=4BDFD67E6D0E486796CC_GLZP_33170. 171. ** Severe ** GetSurfaceData: Zero or negative surface area[-2.48515E-005], Surface=4BDFD67E6D0E486796CC_GLZP_34172. 173. ** Fatal ** GetSurfaceData: Errors discovered, program terminates.174. 175. ...Summary of Errors that led to program termination:176. 177. ..... Reference severe error count=24178. 179. ..... Last severe error=GetSurfaceData: Zero or negative surface area[-2.48515E-005], Surface=4BDFD67E6D0E486796CC_GLZP_34180. 181. ************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).182. 183. ************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.184. 185. ************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.186. 187. ************* EnergyPlus Sizing Error Summary. During Sizing: 2 Warning; 0 Severe Errors.188. 189. ************* EnergyPlus Terminated--Fatal Error Detected. 41 Warning; 24 Severe Errors; Elapsed Time=00hr 00min 1.51sec190.…