st with 6 branches the first 3 having 8 items and the last three having 4 items . I really want to say take list 1 and add list 2 onto the bottom of it so i get a list with 9 branches each with 4 items?
As always thanks wonderful forum!…
EC
1. Between hours 1:00 to 24:002. Current document units is in Meters3. Conversion to Meters will be applied = 1.0004. [1 of 7] Writing simulation parameters...5. [2 of 6] No context surfaces...6. [3 of 6] Writing geometry...7. [4 of 6] Writing materials and constructions...8. [5 of 7] Writing schedules...9. [6 of 7] Writing loads and ideal air system...10. [7 of 7] Writing outputs...11. ...... idf file is successfully written to : c:\ladybug\Freeformtower_IDF\EnergyPlus\Freeformtower_IDF.idf12. 13. Analysis is running!...14. ......
Done! Read below for errors and warnings:
15. 16. Program Version,EnergyPlus-Windows-64 8.1.0.009, YMD=2015.04.04 23:39,IDD_Version 8.1.0.00917. 18. ************* IDF Context for following error/warning message:19. 20. ************* Note -- lines truncated at 300 characters, if necessary...21. 22. ************* 577 Zone,23. 24. ************* Only last 1 lines before error line shown.....25. 26. ************* 578 Freeformbuilding27. 28. ** Warning ** IP: IDF line~578 Comma being inserted after:" Freeformbuilding" in Object=ZONE29. 30. ** Severe ** Out of range value Numeric Field#5 (Type), value=0.00000, range={>=1 and <=1}, in ZONE=FREEFORMBUILDING31. 32. ************* IDF Context for following error/warning message:33. 34. ************* Note -- lines truncated at 300 characters, if necessary...35. 36. ************* 586 BuildingSurface:Detailed,7341.
…
a sort of diagram of the way indoor and outdoor spaces relate to the houses' opaque and transparent boundaries. The two houses pictured are the original designs for houses 8 and 9, by Charles Eames and Eero Saarinen.…
output will show a tree with 3 branches of 4 integers each that I can pass on to other components. What is the best way to do it?
I have tried creating a tree and using a for loop to do so, but it didn't work.
Thank you for your help.
…
Thanks, Chris!
I put a slider into the U-count and tried values from 1 to 60 (I have 9 input curves). I get surfaces at 2, 4, 8, 19, and 38. All are nonsensical surfaces though...
wim
an be given as 88° and 95°. All three angles must sum up to 180, and we're already 3 degrees over balance. Or maybe the user specifies three edge-lengths: 21, 12 and 8. 21 is bigger than 12+8, so even if the triangle was stretched flat, the two short edges cannot reach the ends of the long edge. The above is easy to test for and I add errors to the component if an invalid triangle is provided. However there are also many angle+edge length combinations which result in invalid triangles.
I could of course test for these as well, but the problem is now tolerance. What if the user specifies a redundant angle of 54.7°, whereas the mathematics tell us that the actual angle is 54.7002°. Is that an error? If so, is the angle wrong or is perhaps one of the edges wrong? Or has the triangle simply been over-constrained? Is there a mathematically robust way of dealing with this? And if so, would that also be the most user-friendly way of dealing with it?…
Added by David Rutten at 2:23pm on August 23, 2014
s 8, 4, 2, 10, 1, 3, 8, 4, 2, 0. But then for the end result to maintain all numbers above 5 but replace all numbers below with a defined number..Let's say zero. So then the list would read...8, 0, 0, 10, 0, 0, 8, 0, 0.…
which will result in creating a check for each branch with one item to be 'matched' (in this case to see if it is included in the domain) with all three domains in the single list. so in the end you get a data tree with 8 branches (derived from the 8 grafted values) with 3 items in each branch, that are the check of each initial value with the 3 items domain list.
thank you for sharing the other option too!.
cheers
alex…
o luck so far. I get the same error every time. I am attaching a print screen. Thanks to anyone who makes an effort
P.S. My PC is running now Windows 8 Enterprise N RTM x64 Build 9200 …
Added by cuki fuki at 1:24am on September 25, 2012