algorithmic modeling for Rhino
I glad to see the permanent progress of the plugin! I am back with my typical question on SRS, but this time in the context of the export to shp.
I have a drawing that is in a right location according to the projected SRS I work with.
What are the exact steps to export the geometry to shp when working with projected SRS?
When I export my geometry to shp, I find it very far from my location needed.
I tried to set EAP to lat = 0, lon = meridian defined in .prj file of the SRS (24). It became better, but 500000 m on east from the right location. This false 500000 m easting is defined in prj as well. So I moved my geometry to the left on 500000 m. And nevertheless it is lower than 160 m from the exact location. And that was Greek Grid (2100)
While testing UTM zone 35N for the same location, the results are worse: I have my geometry to 500000 on east. When I subtract -500000 move my geometry in Grasshopper it moves further on east. Maybe I should do some transformations with Heron, but I didn't find any instructions on this topic.
Thank you in advance!
Thanks for your questions, you're previous input was part of the push to get HeronSRS to work.
Try getting the origin of the SRS in Lat/Lon by inputting 0,0 in the Coordinate Transformation component using the SRS of interest as the source and WGS84 or EPSG:4326 as the destination. Then set the EAP to the Lat/Lon coordinates of the source SRS.
If you post a file with the geometry you are looking to export internalized, I can try to make sure the export is landing in the right spot.
Thank you, Brian,
I definitely owe you a coffee. It works!
However here is a tiny issue I can ignore for my purposes. Any transformation (in my case it is from Greek Grid to WGS84) leeds to error. it is the same when you will translate from English to French and back using Google translate. I see that the error becomes around 3cm, which is not critical.
However I would prefer to avoid any transformation if I make my masterplan in Civil 3D and 3D modeling in Rhino within the same projected coordinate system.
Thank you for your time! You have to turn on donates for sure.
Glad it works! I was going to test your gh file, but the polylines weren't internalized:
Are you planning to go between Civil3D and Rhino in EPSG:2100? Also, are you moving your geometry because you are modeling close to the Rhino 0,0 then need to export with an SRS of EPSG:2100?
If you're feeling generous, I do, in fact, have a Patreon page that I haven't advertised:
I have to prepare the internalized geometry later, apologies for the incovenience.
Yes, I have a masterplan in Civil 3D with 2D outlines and a 3D road network in ESPG:2100. The road network goes directly into InfraWorks. The outlines in DWG without any transformation as a plain CAD drawing go directly to various architects and they often shift the outlines closer to 0,0,0. Also, when I get the models from architects, I can generate in Rhino and Grasshopper some landscape features, vegetation or earthwork - sometimes much easier, than in Civil 3D. So I use the shp format to export them to InfraWorks - using a shift received from architects - and assign different styles.
Yes, I could buy FME for these purposes, but it as an awful 3D visualization and not so handy at this scale.
Please, find attached a zip archive with a gh definition and geometries internalized (it's a simple rectangle). There are also the same initial rectangle in dwg in EPSG2100 and the shp output from Heron. This shp output from Heron has a slight shift of 3 cm, which is ok for visualization purposes but not the drafting. The dimensions of the rectangle are intact. Also I can't realize how to get rid of a Z shift which comes from the EAP setting -163.4 ..
I'm not able to reproduce the issue with ExportVector on my end, but I do see the SHP you zipped is off.
I have the Rhino document set to meters with a tolerance of 0.001m. Do you have Rhino set to meters as well?
When Heron sets the EAP, I currently don't have an input for elevation, so your -Z vector can be added into the vector you have for move if it's an issue. In theory, if you are staying in EPSG:2100 in both Heron and Civil3D, there shouldn't be an added Z value, but it would be good to know if this is not the case.
Thank you for a prompt reply! Apologies for bothering you with this annoying question.
The key point here is the software. I reproduced your steps in Grasshopper, and there is no issue with any shift. It comes with the same rounded coordinates as it is shown on your screenshot. But if you try to import the initial dwg and the output from Heron into QGIS (it's free) or Civil 3D, "a shift happens".
I have checked another case when I import a rectangle into Rhino and export it to shp without any shift, "as is". The final shift in QGIS became less, but nevertheless it exists.
So in Rhino there are no issues with horizontal or vertical shifts, problems occur in GIS software.