Problems with making PlanarSrf from Polyline in a grid

Replies to This Discussion

Permalink Reply by Tudor Cosmatu on January 18, 2010 at 12:06pm

hi,

It's not working because your polyline is not planar. What you can do is loft through lines.
Here is your deffinition with a little mod.

Attachments:

• Surfacediagrid.ghx, 149 KB

Permalink Reply by Stencil on January 18, 2010 at 12:21pm

Oh, now I get it. Didn't think of them not being planar. Loft is however not what I had in mind since the surfaces need to be planar.

Is it possible to make a grid on a non-planar surface, but whith grid cells are planar?

Permalink Reply by Suryansh Chandra on January 18, 2010 at 1:00pm

I haven't seen your definition, but it sound pretty simple.

Take all your points that make polylines (if you dont have them, you can use the CV component in version 0.60059 to get them), decompose them into X-Y-Z coordinates, recreate them with only the X-Y (which makes them flat by the Z being 0 by default), then make your polylines, and then the PlanarSurfaces.

Permalink Reply by Stencil on January 18, 2010 at 3:54pm

I think I understand what you mean, I tried it anyway, but that only leaves me with a bunch of points with Z-value 0, lying flat on the "ground". The point was to make a grid on a lofted surface in Rhino in a way that would create planar cells on the non-planar surface.

But maybe I didn't understand you sollution correctly?

Permalink Reply by Suryansh Chandra on January 18, 2010 at 4:36pm

Stencil,

If a nurbs surface is not planar, how do you intend to make planar patches on it?

Surely, it can be done, but it requires far more advanced algorithms which resolved a doubly curved surface into planar flat quads. This is the kind of technique often used in panellization of building skins, where a freeform surface is converted into smaller, flat, buildable pieces.

Mathematically speaking, you will always need 3 points to define a plane, which is always flat. In your case, you would have to project the 4th point onto this plane, and then create the surface to create a flat panel. But doing so would also cause this 4th point to leave the surface, therefore creating gaps with its neighbouring surface quads. Is this what you intend?

Permalink Reply by Stencil on January 19, 2010 at 1:13pm

Thanks Suryansh, that's what I was after. I projected the 4:th point on the surface created by the first 3 points.

However, I've run into a new problem concerning data streams (I think). It's not possible to make a Polyline from the first 3 points and the 4:th projected one. After a bit of investigation I found that the problem may be that the f4:th point have a different path. Can this be a problem when trying to make a polyline? See this picture:

I've attached the new definition if you would have time to look at it.

By the way: you speak of panellization of building skins, and that was what I was trying to achieve at first. Is it possible to create a grid of planar surfaces on a non-planar surface, and do you know if it's been done in GH? The surface quads doesn't have to be square or have parallel edges, they just need to be planar, have 4 corners and not leave gaps with it's neighbouring surface quads.

I'm just starting to learn GH so please be patient with my questions. :-)

Attachments:

• Surface diagrid4.ghx, 181 KB

Permalink Reply by Suryansh Chandra on January 20, 2010 at 7:23am

I'd suggest using a flatten, then graft at all the 4 point streams. Then weave them into one list, and hook it up into a Polyline. That should make the polylines for you. Alternatively, try using the 'Surface from corner points', in which case you'd get a surface in the end instead of a polyline, but you can circumvent the whole flatten-graft-weave process.

About panellization, especially the one dealing with creating flat quads on a doubly curved surface -- ITS ANYTHING BUT SIMPLE.. to start with, since the panels are flat, it will never be exactly as the original surface (since you'd convert curved profiles to straight fragments in polylines). So obviously, you will have to deal with a tolerance in mind as to what degree of deviation is acceptable. There are specialized service providers in the commercial world like Evolute who have developed fairly complex algorithms to do exactly those kind of things. For simpler surfaces, it is somewhat possible to write algorithms yourself that do this, but it does involve a great deal of math and scripting proficiency. It's not possible without recursion.. so its not something that GH can do without scripting.

For starters, you could look at Panelling Tools.

Permalink Reply by Stencil on January 20, 2010 at 8:53am

Thanks for giving advice! I will try this sollution later tonight. And thanks also for explaining the panellization, I will look into both Evolute and Panelling tools.

Permalink Reply by Fabio Plv on January 24, 2011 at 3:54pm

actually as an approx, it works fine...  thanks for sharing

Permalink Reply by taz on January 24, 2011 at 4:19pm

Daniel also has some tricks up his Kangaroo sleeve...

 

http://www.grasshopper3d.com/photo/pqmesh-1?context=user