Toyin Lawal's Page

Dedackelzucht replied to Toyin Lawal's discussion filleting curves and rotating shapes

"like this?"

Nov 5, 2012

Toyin Lawal replied to Toyin Lawal's discussion filleting curves and rotating shapes

"I meant i needed the rectangle to be perpendicular to the XZ plane."

Nov 5, 2012

Dedackelzucht replied to Toyin Lawal's discussion filleting curves and rotating shapes

"Did I understand you right? Best Regards DeDackel"

Nov 5, 2012

Toyin Lawal posted a discussion

filleting curves and rotating shapes

Hi guys, please does anyone know how I can fillet two curves meeting to create a rounded end rather than the sharp joint.In addition, i've placed rectangles and points at the end of a curve but the rectangle is parralel to the XY plane, i need it to be perpendicular to the XY plane.ThanksSee More

Nov 5, 2012

3 Comments

phillip replied to Toyin Lawal's discussion Using a surface to trim curves

"like this? "

Jul 17, 2012

Agneesh replied to Toyin Lawal's discussion Using a surface to trim curves

"Hi Toyin, it will help if you upload ur definition and / or image of what u r trying to achieve. cheers"

Jul 17, 2012

Mario L replied to Toyin Lawal's discussion Trimming off curves at the edge of a surface

"if i understand the image correctly, you're trying to trim the diamond shapes that don't lie on the surface? the first thing you could do is intersect the lines that lie part and part off the the surface with a curve/curve (one curve being…"

Jul 15, 2012

Toyin Lawal posted discussions

Jul 15, 2012

NYCCTfab (Brian Ringley) replied to Toyin Lawal's discussion Making a brep into a surface

"I think it's ok to have the planar curve. Surfaces must be defined by continuous curvature, which is why you can't create a single surface from curves that have been joined (the points at which they meet are discontinuities). Filleting…"

Jul 14, 2012

Toyin Lawal replied to Toyin Lawal's discussion Making a brep into a surface

"Thanks a lot, the problem must have been in the loft. one of the lofted curve is a planer curve, could that be the reason? there are three curves, two of those three are joined curves (3 curves joined together) and the point of joining of these…"

Jul 14, 2012

NYCCTfab (Brian Ringley) replied to Toyin Lawal's discussion Making a brep into a surface

"A BRep (short for boundary representation) is a 3D modeling umbrella term that typically includes both surfaces and polysurfaces - so if you have an open BRep from a GH loft component, chances are it's a surface. You should be to connect your…"

Jul 14, 2012

Toyin Lawal posted a discussion

Making a brep into a surface

Please does anyone know how to turn an open brep resulting from 3 lofted curves into a surface. i want to subdivide this surface into segments. thanksSee More

Jul 14, 2012

3 Comments

Toyin Lawal replied to Toyin Lawal's discussion Reversing a curve

"Thanks Danny, You are a live saver. I'll post any further problems i might have as I continue with d thesis. "

Jul 8, 2012

Danny Boyes replied to Toyin Lawal's discussion Reversing a curve

"There is a Flip Component in the Curve Tab > Utility Panel "

Jul 8, 2012

Toyin Lawal posted a discussion

Reversing a curve

Please does anyone know how to reverse the values on a curve such that the start point on the curve now becomes the end point and the end point then becomes the start point? ThanksSee More

Jul 8, 2012

2 Comments

Danny Boyes replied to Toyin Lawal's discussion using graphmapper to adjust curves

"There is the Shatter Component you need to give it the parameter of the curve at which you want to split it. For this you will need the Curve CP Component (Closest Point)."

Jul 6, 2012