Grasshopper

algorithmic modeling for Rhino

Ifigenia Lambrou
  • Female
  • Limassol
  • Cyprus
Share on Facebook
Share

Ifigenia Lambrou's Friends

  • Marios Tsiliakos
  • Odysseas Georgiou
  • Patrick Bedarf
  • Agnes Tan

Ifigenia Lambrou's Groups

Ifigenia Lambrou's Discussions

Holes on elastic membrane mesh
3 Replies

Hello guys,I've been trying to generate an elastic fabric and the holes produced under stretching it. I have attached the code I worked so far. Unfortunately it doesn't behave as I exprected.…Continue

Tags: membane, tension, compresion, attractors, holes

Started this discussion. Last reply by William Bellamy Feb 20, 2014.

Space Frame
2 Replies

Dear All,I have to make a space frame, around a cylinder surface. I have a problem with lines between centers and edge points. I need to have pyramids, through centers of one surface to edges of…Continue

Tags: frame, space

Started this discussion. Last reply by Ifigenia Lambrou Jan 11, 2013.

Torus
7 Replies

Hello,I need to make a torus, but I'm facing two problems.1) The radius of the circles.The radius of each circle is the distance between the center (on the axis) and the divisions of the curve.…Continue

Tags: torus, grasshopper

Started this discussion. Last reply by Ifigenia Lambrou Jun 10, 2012.

 

Ifigenia Lambrou's Page

Latest Activity

Mark Pothier replied to Ifigenia Lambrou's discussion Is it possible to alter lists of Anchor points while Kangaroo is running? in the group Kangaroo
"Following up on this topic... I have a similar problem. Let's say I am manipulating the ends of a surface with anchor points, while the surface is constrained with springs and hinges. I want to "add" an anchor point somewhere in the…"
Apr 30, 2016
Ifigenia Lambrou liked Daniel Piker's video
Nov 20, 2014
Ifigenia Lambrou liked Daniel Piker's video
Nov 20, 2014
Ifigenia Lambrou liked Systemiq's video
Nov 20, 2014
Ifigenia Lambrou added a discussion to the group gHowl
Thumbnail

Kangaroo-gHowl (Processing) - Error

Hello,I’m working on an algorithm in Kangaroo, in order to see physical transformations and I have connected this with Processing via gHowl in order to send and receive data.In order to run the procedure, I run the Kangaroo simulation first to receive physical forces applied (gravity, collision with surface, etc) and then run Processing algorithm. When this happens Processing is working since it runs and loops but the transformation in Rhino does not show.When I try this without Kangaroo, this…See More
Jul 28, 2014
Ifigenia Lambrou added a discussion to the group Kangaroo
Thumbnail

Kangaroo-gHowl (Processing) - Error

Hello,I’m working on an algorithm in Kangaroo, in order to see physical transformations and I have connected this with Processing via gHowl in order to send and receive data.In order to run the procedure, I run the Kangaroo simulation first to receive physical forces applied (gravity, collision with surface, etc) and then run Processing algorithm. When this happens Processing is working since it runs and loops but the transformation in Rhino does not show.When I try this without Kangaroo, this…See More
Jul 28, 2014
Ifigenia Lambrou replied to Ifigenia Lambrou's discussion Is it possible to alter lists of Anchor points while Kangaroo is running? in the group Kangaroo
"Thank you Joshua for your answer.  Controlling points from Grasshopper was not the task, but what I wanted was to alter them from Kangaroo which produces error as you 've said.  However, I 've done some other way without moving…"
May 10, 2014
Joshua Jordan replied to Ifigenia Lambrou's discussion Is it possible to alter lists of Anchor points while Kangaroo is running? in the group Kangaroo
"There are probably better people to answer this, but here's my shot.Not sure of your particular desired result.  In my experience, you can move anchor points freely as long as they are in the right place when the Kangaroo simulation…"
May 1, 2014
Ifigenia Lambrou added a discussion to the group Kangaroo
Thumbnail

Is it possible to alter lists of Anchor points while Kangaroo is running?

Hello guys,I have a general question about Kangaroo possibilities via Anchor Points. Is it possible to automatically alter anchor points while Kangaroo is running?When the algorithm is running it receives Forces and has some anchor points that I've set at the beginning. What I actually need is when running the algorithm, it should be possible to automatically replace the first list of anchor points with new ones. The reason for doing this is that the kinetic behaviour is based on this…See More
May 1, 2014
Luis Acevedo liked Ifigenia Lambrou's photo
Apr 12, 2014
Ifigenia Lambrou liked Dhruv Seth's photo
Apr 3, 2014
Tatiana Romanova liked Ifigenia Lambrou's photo
Apr 1, 2014
Ayman Mostafa Mohammed liked Ifigenia Lambrou's photo
Mar 31, 2014
Eblis Zhang commented on Ifigenia Lambrou's photo
Thumbnail

housing

"fantastic!!"
Mar 31, 2014
LWX commented on Ifigenia Lambrou's photo
Thumbnail

housing

"Awesome! thanks man ! :)"
Mar 30, 2014

Profile Information

Company, School, or Organization
University of Cyprus
Web or Blog
http://www.facebook.com/ikreatedesignstudio

Ifigenia Lambrou's Photos

Loading…
  • Add Photos
  • View All

Ifigenia Lambrou's Videos

  • Add Videos
  • View All

Comment Wall

You need to be a member of Grasshopper to add comments!

Join Grasshopper

  • No comments yet!
 
 
 

Translate

Search Grasshopper

Photos

  • Add Photos
  • View All

© 2017   Created by Scott Davidson.   Powered by

Badges  |  Report an Issue  |  Terms of Service