Grasshopper

algorithmic modeling for Rhino

Erik Pelicaen
  • Brussels
  • Belgium
Share on Facebook
Share

Erik Pelicaen's Groups

Erik Pelicaen's Discussions

Mesh Split/Trim/Difference?

Hi.I think it should be pretty easy but I've been trying to connect wires everywhere and none of the options was right. I have used Mesh Split, Mesh Trim and Mesh Difference.As you can see in the…Continue

Started Aug 16, 2016

Karamba Supports

Hi there.I have hopelessly been trying to define my supports in Karamba, without succes.It keeps showing me this message:Solution Exception: Could not find node where support number 0 is attached.I…Continue

Started Aug 11, 2016

RhinoVault Push/Pull Locally

Hello, I know this is a Grasshopper forum but there isn't really a RhinoVault forum.For those of you who work with RhinoVault, would anyone have any suggestions of obtaining what the arrows suggest…Continue

Started Aug 9, 2016

Karamba cross-section Optimization

Hello everyone.I'm new to Karamba and I'm wondering if it is possible to optimize the cross-section of a shell, but not by picking from a list of standardized cross-sections.The picture below is that…Continue

Started Aug 5, 2016

 

Erik Pelicaen's Page

Latest Activity

HEEN replied to Erik Pelicaen's discussion Lunchbox Quad Panels Equal Sizes
"maybe not I have a question do you how apply or know the size of the panel? I have no computer in this moment to test I mean if i want apply panels with 1 m x 2 m a not panels with a  random size."
Feb 4
Ayk Martirosyan replied to Erik Pelicaen's discussion Lunchbox Quad Panels Equal Sizes
"It is impossible to divide a surface like this into equal quads. How would you imagine that? You can achive more or less even divisions, but it highly depends on the way you construct the surface. If you use curves, then the points on the curve…"
Feb 3
HEEN replied to Erik Pelicaen's discussion Lunchbox Quad Panels Equal Sizes
"have you found the solution?"
Feb 3
DavidLee liked Erik Pelicaen's profile
Dec 17, 2016
Erik Pelicaen replied to Erik Pelicaen's discussion Vault Structural Analysis in the group karamba
"Ok thank you very much Clemens."
Aug 17, 2016
Erik Pelicaen replied to Erik Pelicaen's discussion Voronoi Structural Analysis in the group karamba
"It works now! Thanks again!"
Aug 17, 2016
Erik Pelicaen replied to Erik Pelicaen's discussion Voronoi Structural Analysis in the group karamba
"Ok thank you. I'm using the 1.1.0 version. I'll upgrade and try again."
Aug 17, 2016
karamba replied to Erik Pelicaen's discussion Vault Structural Analysis in the group karamba
"The shell elements were not given an identifier, therefore the initial cross section was not attached to them (see attached definition).You should add asymmetric loads (e.g. via MeshLoads), otherwise the structural response is not…"
Aug 17, 2016
karamba replied to Erik Pelicaen's discussion Voronoi Structural Analysis in the group karamba
"Hello Erik, how many mesh faces do you use for modelling the structure? The most efficient way to reduce the static system is to lower the mesh resolution - as long as it does not have an impact on the structural response (e.g. the maximum…"
Aug 17, 2016
Erik Pelicaen added 2 discussions to the group karamba
Aug 16, 2016
Erik Pelicaen posted a discussion

Mesh Split/Trim/Difference?

Hi.I think it should be pretty easy but I've been trying to connect wires everywhere and none of the options was right. I have used Mesh Split, Mesh Trim and Mesh Difference.As you can see in the picture below, I have a Voronoi mesh (red) and a solid mesh (green).I just need the Voronoi mesh that is inside the solid mesh, so just cut off the parts that are outside of the green panel.Unfortunately I cannot upload the .gh file because it is over 5 MB...…See More
Aug 16, 2016
Erik Pelicaen replied to Erik Pelicaen's discussion Vault Structural Analysis in the group karamba
"However, I cannot optimize the cross section, whereas I am doing exactly the same thing as in one of the example files. Do you know what I'm doing wrong?"
Aug 16, 2016
Erik Pelicaen replied to Erik Pelicaen's discussion Vault Structural Analysis in the group karamba
"That worked. Thank you!"
Aug 16, 2016
karamba replied to Erik Pelicaen's discussion Vault Structural Analysis in the group karamba
"With Karamba 1.2.1 the 'AnalyzeThI'-component does not throw an exception. The bounding box of your model has a diagonal of length 184000[m]. I think you have to scale your geometry by 0.001 in order to work in meter. Maybe this is the…"
Aug 16, 2016
Erik Pelicaen replied to Erik Pelicaen's discussion Vault Structural Analysis in the group karamba
"Oh right, sorry for that. Here you go."
Aug 16, 2016
karamba replied to Erik Pelicaen's discussion Karamba Cross Section Optimization in the group karamba
"RO114.3/4 is a circular hollow cross section with diameter 114.3mm and 4mm wall thickness. It is used as the default cross section for beams and trusses. The default shell cross section has a thickness of 1cm and is assumed to have the same…"
Aug 16, 2016

Profile Information

Company, School, or Organization
VUB

Comment Wall (1 comment)

You need to be a member of Grasshopper to add comments!

Join Grasshopper

At 5:46pm on July 8, 2016, Amita said…

Nice to meet you, My name is Miss Amita Yilmaz i am from Turkey, i pick interest to know you more after going through your profile, please i want you to contact me through my email address below i have important think to discus with you

( amitayilmz@gmail.com )

 
 
 

Translate

Search Grasshopper

Photos

  • Add Photos
  • View All

© 2017   Created by Scott Davidson.   Powered by

Badges  |  Report an Issue  |  Terms of Service