Thanks for your fast answer.
I tried what you propose, but it doesn't take the 30 paths from the points but the 12 paths from the vectors. see (picture, and file)
EC
1. Between hours 1:00 to 24:002. Current document units is in Meters3. Conversion to Meters will be applied = 1.0004. [1 of 7] Writing simulation parameters...5. [2 of 6] No context surfaces...6. [3 of 6] Writing geometry...7. [4 of 6] Writing materials and constructions...8. [5 of 7] Writing schedules...9. [6 of 7] Writing loads and ideal air system...10. [7 of 7] Writing outputs...11. ...... idf file is successfully written to : c:\ladybug\Freeformtower_IDF\EnergyPlus\Freeformtower_IDF.idf12. 13. Analysis is running!...14. ......
Done! Read below for errors and warnings:
15. 16. Program Version,EnergyPlus-Windows-64 8.1.0.009, YMD=2015.04.04 23:39,IDD_Version 8.1.0.00917. 18. ************* IDF Context for following error/warning message:19. 20. ************* Note -- lines truncated at 300 characters, if necessary...21. 22. ************* 577 Zone,23. 24. ************* Only last 1 lines before error line shown.....25. 26. ************* 578 Freeformbuilding27. 28. ** Warning ** IP: IDF line~578 Comma being inserted after:" Freeformbuilding" in Object=ZONE29. 30. ** Severe ** Out of range value Numeric Field#5 (Type), value=0.00000, range={>=1 and <=1}, in ZONE=FREEFORMBUILDING31. 32. ************* IDF Context for following error/warning message:33. 34. ************* Note -- lines truncated at 300 characters, if necessary...35. 36. ************* 586 BuildingSurface:Detailed,7341.
…
6, 7, 8, 9, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28, 30, etc
In addition to the components in the attached file, I have also tried using Cull Index but that did not do much. I tried using a number slider set to whole numbers with the range equal to the values I have set up in the integer, but it just increases the size by 1 every time. Any help on steps in the right direction would be great thanks.…
ied 12 times in X (always with the same gap) and for each time has a rotation of 30°. Then, I'd like these 12 items are copied n times in Y, shifting 1 module per time. At the end, the last 12 items have to be copied again n times in Y, shifting 1 module per time, but in the opposite way (like a Z).
See attached an example.
Thank you for your help!
…
and Ronnie of StudioMode and David Fano of DesignReform will also be attending.
RSVP has been closed on this event. Space is limited to 50 people. Please attend if you do RSVP.
Agenda -
12:00-1:00 Arrival, informal discussion
1:00 - 1:15 Introductions
1:15 - 2:00 Project presentation 1 (30 minutes + 15 min QA) - David Lee - Clemson - 3D pattern environments using volumetric proxies.
2:00 - 2:45 Project Presentation 2 (30 minutes + 15 min QA) - P. Casey Mahon - Organic Abstractions (30 minutes + 15 min QA)
2:45 - 3:45 David Rutten - New work in GH (30 min QA)
3:45 - 4:30 Sameer Kumar AIA - KPF - Project presentation 3 (30 minutes + 15 min QA)
4:30 - 5:15 Chris Wilkins - Clemson - Urban Renewal and parametric urban development studies in Grasshopper.
5:15 - 6:00 David Rutten - Scripting in GH (15 min QA)
After 6:00 conversations may move down the street for more discussion.
If you would like to present your project at the Cloud please email: scottd@mcneel.com…
onent are experiential or location specific. For example: humidex has been derived and widely used in Canada.Also both humidex and discomfort index should be used in in-shade conditions.For universal applications and locations, you should concentrate on either PET or UTCI (this is what "Outdoor Comfort Calculator" component is based on).
I have found out, that for instance - OutdoorComfortCalculator - which considers temperatures of 9-26 and other factors, gives the % of comfortable time outdoor for instance in Kenya in Africa (high temperatures and humidity) 55%, whereas within the same .epw data and some additional factors added to the Thermal Indices component, the "humidex" or "Discomfort index" give a result drastically lower, I think it was even 1-5% comfortable.How is that?
Yes, this is one of the issues that I have with UTCI index: the authors wanted to make it as an index applicable in any type of climate. To create the UTCI comfort categories a number of data has been collected from different locations (for hot humid climate, it was the data from Madagascar. I may be wrong on this). This resulted in universal comfortable range of 9 to 26 C which you mentioned. How would the people in Madagascar perceive the feel like temperature of 9 degrees as comfortable is beyond my understanding.Thermophysiology of a human in Madagascar, and in Poland is the same. However their acclimatization is quite different, which raises the issue with the upper universal comfortable range. In general people who live in hotter climates have a bit higher tolerance to high temperature than those living in continental climates. And vice-versa: their tolerance to lower temperatures is lower than the tolerance of the people from the continental climates. Here is a comparison of the UTCI - PET stress categories:
UTCI
all climates stress category
above +46 extreme heat stress+38 to +46 very strong heat stress+32 to +38 strong heat stress+26 to +32 moderate heat stress+9 to +26 no thermal stress+9 to 0 slight cold stress0 to -13 moderate cold stress-13 to -27 strong cold stress-27 to -40 very strong cold stressbelow -40 extreme cold stress
PET
(sub)tropical humid climate temperate climate stress categoryabove +42 above +41 extreme heat stress+38 to +42 +35 to +41 strong heat stress+34 to +38 +29 to +35 moderate heat stress+30 to +34 +23 to +29 slight heat stress+26 to +30 +18 to +23 no thermal stress+22 to +26 +13 to +18 slight cold stress+18 to +22 +8 to +13 moderate cold stress+14 to +18 +4 to +8 strong cold stressbelow +14 below +4 extreme cold stress
I attached below an example of PET humid climate comparison with UTCI, for in-shade and out-shade conditions.As it can be seen UTCI shows the percent of time comfortable: two times higher than PET.
Thank you Pin, for the useful comment, on usage of "Analysis period" component.…
o three parts:
branch 1:
{0;0} N = 3
{0;1} N = 3
branch 2:
{1;0} N = 5
{1;1} N = 5
branch 3:
{2;0} N = 30
{2;1} N = 30
parthmapper won't change the length of branch, explode tree won't give me two branches in one output
…