used of 180 being for the northern hemisphere and 0 for the southern hemisphere.For the optimal tilt, to my knowledge, they are mostly based on correcting location's latitude through a single formula.TOF component is more sophisticated. It essentially replicates the Solmetric's Annual Insolation Lookup tool.What it does is that it creates a grid of points. Each point represents the calculated annual insolation on the surface (PV module, SWH collector, facade, any kind of surface) for a single tilt and azimuth angle.Each point is then elevated according to the annual insolation values. The mesh is created from that grid of points. The portion of the mesh which is the highest, represents the optimal tilt and azimuth angles. So the higher your "precision_" input is, the more points in a mesh you'll have - thus the more precise final optimal tilt and azimuth will be.For the diffuse component of the annual incident solar radiation for each point the Perez 1990 modified model is used. Direct is from classical cosine law, and Ground reflected component from Liu and Jordan (1963).So TOF component calculates the optimal tilt and azimuth based on annual incident solar radiation, not AC energy....…
rce of power.
A fortified emplacement for heavy guns.
Synonyms
accumulator
And use component:
com·po·nent
/kəmˈpōnənt/
Noun
A part or element of a larger whole, esp. a part of a machine or vehicle.
Adjective
Constituting part of a larger whole; constituent.
Synonyms
noun.
constituent - element - ingredient - part
adjective.
constituent - constitutive
…
n to finding a concave contour polyline (which is in general what you need). In your case each contour section contains a series of points of which you do not know the order and you need to sort them so that by connecting them you find the contour. This is fairly easy to do when the contour is convex (basically you find the average point then calculate the vectors from the average to the points and sort the vectors by angle - sorting the points by the same angle gives you the right order for the contour), but generally impossible to find uniquely when the contour is concave (PS: convex means that, for ANY 2 points inside the figure, a straight line connecting them doesn't intersect with the border curve - i.e. circles, ellipses, rectangles, triangles - concave shapes are a star, a crescent moon, an arrow, a boomerang, etc.).
The problem goes like this: given a generic list of points:
Each of these configurations for a perimeter equally fits the above:
Laurent already went for another possible solution, the stochastic approach (by subdividing the connecting lines), I slightly adjusted a few things over his solution:
namely, I added a rounding option to adjust for some weird tolerance issues (some points that should be at Y=80 were at Y=79.99998 or something) and a more straightforward solution to group them by section plane using sets logic. This, coupled with alpha shape, gives a quite good approach, still very coarse in terms of results but that depends on the sampling resolution of the field (i.e. number of height sections in which you calculate the metaballs) and sampling length of the connecting lines.
Definition attached.…
Diffraction , I left it, how it is.
For the unusual issues that comes in the image source component, so, is it something strange? But, I still have the same issues when I sets any integer component (single or multiple) in the “reflection order” of the image source component, in the “image source order” in the ray tracing component, and again, when I connect the output “Direct sound data” of Direct Sound component in the Energy Time Curve.
Do I wrong something with the integer component? I used it already in the first parts, for sets “grasshopper layers”, in the “Scene” component, but here it works. Should I start with a new file?
For the multi-object optimization, thank you for all suggestions. Yes, I red PHD thesis work of Tomas Mendez and the article “ EDT, C80 and G Driven Auditorium design” and still others. Thank you to all these articles, I decided where to focus my thesis.
I understand the potential of Multi-object optimization, and problems that I can finding without using it. Actually, in the beginning of my thesis, I tried to jet in contact with the Politecnico di Torino, but was not easy because I’m not a Politecnico student.
Here, in University of Florence (Building engineering), there isn’t a department or someone that is already familiar with these field of study, so, as you can image, for design my thesis, I can confide on online resources. So far, my Professor suggest me to begin with a Nonlinear Global optimization like Galapagos, and only after see the multi-object. In this way, step by step if something doesn’t work is easier to understand way and where something is going wrong: if are problems due to the setting of the programs, because we are not practical about these, or if there is a wrong in the simulations or in the algorithm and ect.
Do you think is a good way for go on?
Thank you very much,
Kind Regards
Giulia
…
ram.com/Helicoid.html.
To be more precise, I'm not quite clear how to apply this equation to the helicoid and integrate it into my code:
where corresponds to a helicoid and to a catenoid.
I've made some attempts not worth to be shown here. Maybe somebody can help me with a pseudocode or a simple description how to start solving this classic geometric transformation.
Thanks, Sebastian
…
Added by Sebastian at 11:19am on December 27, 2012
ails.
Some word about the mesh... (see Image_01)
I took a flat 4 points NURBS surface as imput (very easy, it defines the total area of my pavilion) and some points (that defines the contact with the ground).
Then I extracted a grid of points from the NURBS (Surface_Util_Divide surface) and compared 'em with the contol points, in order to associate to each grid's point its own attractor (Vector_Point_Closest Point).
Than I moved the points down. I used the distance from each point to its attractor (inverted) as amplitude for the vector of the movement, in order to say: the nearer you are to the control point, the more intense your movement will be. During this operation I've passed the distances' data list into a graph mapper (Params_Special_Graph Mapper), in order to regulate in a very intuitive and interactive way the shaping of my canopy.
At the end of the process I asked GH for a simple Delaunay mesh (Mesh_Triangulation_Delaunay Mesh). It's a very cool command, I believe!!!
Ok, now some word about the component, it's design and it's repetition/adaptation to the mesh...
(see Image_02)
I took the mesh and extracted components on first and faces's information on second. Then I selected and separated the vertexes (1°, 2°, 3°) of each triangular face into threee well defined list.
Then I re-created the triangles' edges. Please pay attention because it's not the same if you use output information from Delaunay components, because here we need a justapposition of edges where triangles touches each others.
After this work I joined the edges and found their centroid. At the same time I found the mid point of each edge.
Now the component... (see Image_03)
It' a little bit longer to describe: I'll try to be synthetic.
Substantially it is a loft from a curve to a point, repeated three times for each triangle (Surface_Freeform_Extrude Point). The point is an elevation of the centroid of the triangle (you can choose if the exstrusion has a single height or it's related to an attractor. In my case it was fixed). The curve is combination of things. There's an arch, which starts on the edge (there's an offset from the corner) end terminates on the same edge (on the other side, obviously). While it's generation the arch passes through a third point which belong to another segment. This last connects the mid point of the original edge (base triangle) with the centroid. The result is a kind of polyline, with two segments and an arch. If you go back to the image of the component that I posted probably you'll understand what I'm saying better than with the definition.
The posit…
this common installation problem please find a tested remedy shared by one of the group members:
Comment by Iman Sheikhansari on August 26, 2019 at 8:33amDelete Comment
HiIf you are encountering a problem with rhino 6 versions don't worryFollow these steps.1. Download SYNTACTIC from https://sites.google.com/site/pirouznourian/syntactic-design2. Install it and go to the installation folder, Drag & drop SYNTACTIC(green one) over your grasshopper canvas.3. Close your rhino and reopen it. 4. Type GrasshopperDeveloperSettings5. Tick the Memory load *.GHA assemblies using COFF byte arrays option6. Run grasshopper and enjoy plugin
I hope this helps,
Best regards,
Pirouz
…
t the maximum potential with the bridge BIM+PARAMETRIC DESIGN ;D
During this Intense Week, we will learn about the power of Rhino + Grasshopper + ArchiCAD with Professional and Useful examples for our Normal Working day :D
You will get Advanced Library Files + Personal Web + Knowledge and Skills to start using this incredible Methodology ;D
Also, the week is having Lectures from different Experts sharing their Computational Working Experiences ;D And Jam Sessions! opening the door to 5 interesting topics to research, learn and experiment together :D
2020 is your YEAR ;D !!!
Complete details and registration……
hopper no requiere de conocimientos de programación o scripting para permitir al diseñador trabajar de forma generativa y paramétrica. No son necesarios conocimientos previos de Grasshopper pero sí de Rhino a nivel básico.
Controlmad es Centro Formador Autorizado Rhinoceros y Rhino fab Studio.
Nuestros profesores son Instructores Autorizados Rhinoceros con experiencia universitaria, nacional e internacional.
El curso y los ejercicios a desarrollar están enfocados a diseñadores, arquitectos, ingenieros y estudiantes.
En este curso introductorio el alumno se familiarizará con términos básicos de la estructura de Grasshopper, como “listas de datos”, “dominios”, “estructuras en árbol”, etc.
Es un curso de 18 horas, con el que se pretende entrar en la lógica de trabajo de Grasshopper mediante diversos ejercicios, de forma que el alumno sea capaz posteriormente de desarrollar sus propias gramáticas, con la confianza que da comprender los términos básicos de programación sobre los que se apoya todo el sistema de trabajo de Grasshopper.Para este curso no son necesarios conocimientos previos de Grasshopper, pero sí de Rhino (a nivel básico).
También se vincula el programa con la impresión 3D aprendiendo a exportar archivos desde Grasshopper con los requisitos mínimos de impresión 3D. Se realizará una demo de impresión en el aula.
El primer día del curso se le facilita al alumno un manual-tutorial con los ejercicios a realizar, en PDF.
A la finalización del curso, y siempre que el alumno haya asistido al 80% de las clases, se le otorgará un diploma oficial acreditativo del curso.
Fechas: 5, 6, 12 y 13 de marzo
Horario: sábado y domingo 16 - 20,30h (Madrid, CET)
Lugar: Sesiones On-line en directo a través de nuestra plataforma online.controlmad.com
…
of a hack to push it to an android device, and you can't use labels, which is a very bad point!
...
I won't buy an Iphone!
The other is Control OSC. It looks rougher, but it has a lot of advantages to me.
+ Game of Life included!
+ you can use and update labels :))
+ Has a nice muti touch widget unfeatured in touch osc
+ You can script the interface using java script manipulation in gh, stream it to your dropbox and update in one "tap", as follows
Does anyone have experience with scripting interfaces for this software? I'm stuck already. I know nothing of java script to begin with. As you can see I managed to format the labels but the osc message I could not find a way, it stays untouched.
Just in case someone knows better, here are my "objects" (I said that right?). The userXXX are replaced in GH.
{ "name":"userName", "type":"Slider", "x":(xPadding + .11), "y": yPadding, "width":.82, "height":.082, "color":"userColor", "min":userMin, "max":userMax, "ontouchmove" : "var roundedvalue = this.value.toFixed(userFix); LbluserName2.changeValue(roundedvalue)", "onvaluechange": "oscManager.sendOSC('/userName', 'f', this.value.toFixed(userFix))",},{ "name":"LbluserName1", "type":"Label", "x":xPadding, "y": yPadding, "width":.1, "height":.05, "color":"userColor", "value": "userName"},{ "name":"LbluserName2", "type":"Label", "x":xPadding, "y": (yPadding + 0.05), "width":.1, "height":.05, "address":"/userName", "color":"userColor", "value": 0},…