EP output variables are to calculate outdoorAirEnergy?
Thank you very much!
Output variables on the Read EP Results component:[1] totalThermalEnergy=cooling+heating[2] thermalEnergyBalance=cooling (-)andheating (+)[3] cooling= Zone Ideal Loads Supply Air Total Cooling Energy [J](Hourly)=Zone Ideal Loads Supply Air Sensible Cooling Energy [J](Hourly)+ Zone Ideal Loads Supply Air Latent Cooling Energy [J](Hourly)[4] heating= Zone Ideal Loads Supply Air Total Heating Energy [J](Hourly)= Zone Ideal Loads Supply Air Sensible Heating Energy [J](Hourly) + Zone Ideal Loads Supply Air Latent Heating Energy [J](Hourly)[5] electricLight=Zone Lights Electric Energy [J](Hourly)[6] electricEquip=Electric Equipment Electric Energy [J](Hourly)[7] peopleGains=Zone People Total Heating Energy [J](Hourly)[8] totalSolarGain=Zone Windows Total Transmitted Solar Radiation Energy[9] infiltrationEnergy=Zone Infiltration Total Heat Gain Energy (+)andZone Infiltration Total Heat Loss Energy (-)[10] outdoorAirEnergy= ???[11] natVentEnergy=Zone Ventilation Total Heat Gain Energy (+)andZone Ventilation Total Heat Loss Energy (-)[12] operativeTemperature=Zone Operative Temperature[13] airTemperature=Zone Mean Air Temperature[14] meanRadTemperature=Zone Mean Radiant Temperature[15] relativeHumidity=Zone Air Relative Humidity[16] airFlowVolume=[infiltrationFlow] Zone Infiltration Standard Density Volume Flow Rate+[natVentFlow] Zone Ventilation Standard Density Volume Flow Rate+[mechSysAirFlow] Zone Mechanical Ventilation Standard Density Volume Flow Rate+[earthTubeFlow] Earth Tube Air Flow Volume[17] airHeatGainRate=[surfaceAirGain] Zone Air Heat Balance Surface Convection Rate+[systemAirGain] Zone Air Heat Balance System Air Transfer Rate
Output variables on the Read EP Surface Results component:[1] surfaceIndoorTemp= Surface Inside Face Temperature[2] surfaceOutdoorTemp=Surface Outside Face Temperature[3] surfaceEnergyFlow=[opaqueEnergyFlow] Surface Average Face Conduction Heat Transfer Energy+[glazEnergyFlow] Surface Window Heat Gain Energy[4] opaqueEnergyFlow =Surface Average Face Conduction Heat Transfer Energy[5] glazEnergyFlow= Surface Window Heat Gain Energy[6] windowTotalSolarEnergy=Surface Window Transmitted Solar Radiation Energy[7] windowBeamEnergy=Surface Window Transmitted Beam Solar Radiation Energy[8] windowDiffEnergy=Surface Window Transmitted Diffuse Solar Radiation Energy[9] windowTransmissivity=Surface Window System Solar Transmittance…
lass BrepDeform Inherits GH_Component Public Reslist As New List(Of String) Public Sub New() MyBase.New("BrepDeform", "Deform", _ "移动物件的控制点" & vbCrLf & "(Move the control Point to change a object)", "SEG", "Modify")
End Sub Public Overrides ReadOnly Property ComponentGuid As System.Guid Get Return New Guid("8226e0ea-ed6b-47c2-8a24-244f044152d8") End Get End Property Protected Overrides ReadOnly Property Internal_Icon_24x24() As System.Drawing.Bitmap Get Return My.Resources.SEG_BrepDeform End Get End Property Protected Overrides Sub RegisterInputParams(ByVal pManager As GH_Component.GH_InputParamManager) ' pManager.AddTextParameter("Guid", "Id", "将要被替换的犀牛物件" & vbCrLf & "(RhinoObjects that will be replaced)", GH_ParamAccess.item) 'Dim guidParam As New Param_Guid pManager.AddParameter(New Param_Guid, "Guid", "Id", "将要被替换的犀牛物件" & vbCrLf & "(RhinoObjects that will be replaced)", GH_ParamAccess.item) pManager.AddPointParameter("ControlPoint3d", "C", "控制点的位置" & vbCrLf & "(Control Point's location)", GH_ParamAccess.item) pManager.AddPointParameter("NewPoint3d", "P", "新控制点的位置" & vbCrLf & "(New Control Point's location)", GH_ParamAccess.item) pManager.AddNumberParameter("Tolerace", "T", "输入点与物件实际控制点对比的精度" & vbCrLf & "(Tolerace for the Control Point match)", GH_ParamAccess.item, 0.1)
pManager.AddBooleanParameter("BlMove", "M", "如果是True则进行移动" & vbCrLf & "(If true Perform the Move)", GH_ParamAccess.item, False)
End Sub Protected Overrides Sub RegisterOutputParams(ByVal pManager As Kernel.GH_Component.GH_OutputParamManager) pManager.AddTextParameter("Result", "RG", "结果列表" & vbCrLf & "(Result)", GH_ParamAccess.list) End Sub Public Overrides ReadOnly Property Exposure As GH_Exposure Get Return GH_Exposure.primary End Get End Property
Protected Overrides Sub SolveInstance(ByVal DA As Kernel.IGH_DataAccess) If Banner.astrict.showmessage Then Return Dim Ids As Guid = Guid.Empty 'Dim Ids As String = String.Empty Dim tpt As Point3d = Point3d.Unset, opt As Point3d = Point3d.Unset Dim tolar As Double = 0.1 Dim blMove As Boolean = False If Not DA.GetData(0, Ids) Then Return If Not DA.GetData(1, opt) Then Return If Not DA.GetData(2, tpt) Then Return If Not DA.GetData(3, tolar) Then Return If Not DA.GetData(4, blMove) Then Return If Not blMove Then GoTo line1 Reslist.Add(Now & "_未替换!(Replace failed!)") Else Reslist.Clear() ' Grasshopper.Instances.ActiveCanvas.ModifiersEnabled = False End If
' rt.AddRange(docobjlist.Select(Function(geoobj As RhinoObject) GH_Convert.ObjRefToGeometry(New ObjRef(geoobj.Id)))) 'Private Checked(5) As Boolean, Namestr() As String = {"Point", "Curve", "Brep", "Mesh", "TextDot", "TextEntity"}
Try
Dim rh As RhinoDoc = Rhino.RhinoDoc.ActiveDoc Dim rhobj As RhinoObject = rh.Objects.Find(Ids) ' Dim rhobj As RhinoObject = rh.Objects.Find(New Guid(Ids))
Dim bobj As BrepObject = CType(rhobj, BrepObject) RhinoApp.RunScript("Cancel", False) RhinoApp.RunScript("Cancel", False) bobj.Select(True)
RhinoApp.RunScript("_SolidPtOn", False) Dim gobjs As GripObject() = bobj.GetGrips ' rh.Views.RedrawEnabled = False For Each grpobj As GripObject In gobjs
If grpobj.CurrentLocation.DistanceTo(opt) < tolar Then grpobj.Select(True) Dim CurrentPln As Plane = RhinoDoc.ActiveDoc.Views.ActiveView.ActiveViewport.ConstructionPlane Dim tropt As New Point3d(opt), trtpt As New Point3d(tpt) tropt.Transform(Transform.PlaneToPlane(Plane.WorldXY, CurrentPln)) trtpt.Transform(Transform.PlaneToPlane(Plane.WorldXY, CurrentPln))
Dim movestr As String = "_move " + String.Format("{0},{1},{2} ", tropt.X, tropt.Y, tropt.Z) + String.Format("{0},{1},{2} _Cancel _Cancel", trtpt.X, trtpt.Y, trtpt.Z) RhinoApp.RunScript(movestr, True) grpobj.Select(False) End If
Next
'RhinoApp.RunScript("Cancel", False) 'RhinoApp.RunScript("Cancel", False) '' rh.Views.RedrawEnabled = True Reslist.Add(Now & "_替换成功!(Replace Success!)") Catch ex As Exception Reslist.Add(Now & "_替换失败!(Replace failed!)" & vbCrLf & ex.Message)
End Try ' Grasshopper.Instances.ActiveCanvas.ModifiersEnabled = True
line1: DA.SetDataList(0, Reslist) End Sub
'Private Sub Testt_PingDocument(sender As IGH_DocumentObject, e As GH_PingDocumentEventArgs) Handles Me.PingDocument ' Dim Mbool = Aggregate bcbool In Checked Into cb = Any(bcbool)
' If Not Mbool Then ' Checked(0) = True ' Message = Namestr(0) ' Order = 0 ' End If 'End Sub
End Class
The picture below shows the two question.
Question One I must use data dam, or the component can't batch deal the brep. I don't know why, I have You can give me a solution to make it working normal not using the data dam
Question Two I can not uset the Button component, If I use it, the gh canvas will die with some mouse event--. I have see this problem before in this forum,but there is no solution and explain. I want to know why and How to solve it.
I don't know if I have made my question clear,if not give a message. Thank you! Thank you all.
The gh test file and 3dm test file in the upload files.
…
tions or components.
Participants will learn concepts of object oriented programming and essential syntax of C# to endeavour into personally extending cad toolsets. The workshop will focus on introducing the .NET language C# and the Software Development Kit (SDK) RhinoCommon.
Topics
- use of Script Component within Grasshopper
- explanation to the .NET Framework
- introduction to RhinoCommon SDK
- basics of imperative / object-oriented programming
- data types, operators, properties
- variables, arrays, lists, enumerations
- methods
- objects, classes
- control structures: conditional statements (if, else, switch)
- control structures: loops (for, foreach, while, do)
- walk-through iterative und recursive code-samples
- use of RhinoCommon Geometry class library: creation, sorting, editing of Geometry (Points, Vectors, Curves, Surfaces)
- adding (baking) geometry to the active Rhino 3DM Document, including attributes (Name, Layer, Colors etc.)
- introduction to the Integrated Development Environment MS Visual Studio Express Edition
- compiling code to dll/gha files (plug-ins) / making your own Grasshopper custom components
Grasshopper wird auf der .NET Softwareplattform entwickelt, und kann ebenso wie das CAD Programm Rhinoceros mit "RhinoCommon", einem Software Development Kit, erweitert werden.
Dieser Kurs richtet sich an Designer, Architekten, Ingenieure und Techniker, welche mit dem grafischen Algorithmus-Modellierer "Grasshopper3d" sowie dem CAD-Programm "Rhinoceros" bereits vertraut sind und einen Einstieg in die Programmierung von Geometrie erlernen möchten.
Der Kurs Grasshopper II folgende Grundlagen:
Kennenlernen der Script Componente
Erläuterung zum .NET Framework
Einführung in RhinoCommon SDK
Grundlagen d. imperativen / objektorientierten Programmierung
Datentypen, Operatoren, Eigenschaften
Variablen, Reihen, Listen, Aufzählungen
Methoden
Objekte und Klassen
Kontrollstrukturen: Bedingte Ausführung, Schleifen
praxisnahe iterative und rekursive Code-Beispiele für generatives Design unter Verwendung der RhinoCommon Geometrie Klassenbibiliothek - Punkt- und Vektorgeometrie erstellen, sortieren, bearbeiten, Flächen und Netze erstellen - Geometrie in das Rhino 3DM Dokument baken, einschließlich Attribute (Name, Layer, Color)
Einführung in die Entwicklungsumgebung MS Visual Studio Express Edition
Kompilieren von Programmerweiterungen (plug-ins) als Komponenten (custom components)
Details, Anmeldung:
www.vhs-stuttgart.de
Trainer Peter Mehrtens
Kursdauer: 3 Tage x 8 h
Freitag, 21.02.2014, 9:00-17:00 Uhr Samstag, 22.02.2014, 9:00-17:00 Uhr Sonntag, 23.02.2014, 9:00-17:00 Uhr Ort: VHS Stuttgart, Fritz-Elsas-Str. 46/48
Teilnahmegebühr 510,00 €…
our own, understand third-party tutorials and process to the advanced sessions.
register for 29€/3hrs
GMT: SAT, 13 DEC 2014 @ 3:00PM / 29€
Introduction to vectors, vectors vs. points, vector addition, cross product, dot product, vector operations, vector display, practical use, planes/frames, normals.
Introduction to domains, t parameter, evaluate curve, boundaries, remap, reparametrize, UV coordinates, evaluate surface.
GMT: SUN, 14 DEC 2014 @ 3:00PM / 29€
Introduction to data trees, graft, flatten, unflatten, tree statistics, cherry picker, simplify, shift path, path mapper, tree item, tree items.
WEBINARS
The webinars are series of on-line live courses for people all over the world. The tutor broadcasts the screen of his computer along with his voice to the connected spectators who can ask questions and comment in real time. This makes webinars similar to live workshops and superior to tutorials. The rese arch Grasshopper® sessions are unique for their thorough explanation of all the features, which creates a sound foundation for your further individual development or direct use in the practice. All sessions are held entirely in English.
PAST EVENTS
…
Added by Jan Pernecky at 2:27am on December 11, 2014
gh, when I bake, the geometry suddenly exists in rhino.
Second, I can seem to figure out how to set default numeric values in the component.
Protected Overrides Sub RegisterInputParams(pManager As Grasshopper.Kernel.GH_Component.GH_InputParamManager)
pManager.AddPointParameter("Focal Point", "FP", "The focal point", GH_ParamAccess.item)
pManager.AddNumberParameter("Focal Point Horiz Dist", "D", "Focal point distance from performance boundary", GH_ParamAccess.item)
pManager.AddNumberParameter("Focal Point Height", "H", "Focal point height above performance boundary", GH_ParamAccess.item)
pManager.AddPointParameter("First Row Start Point", "FR", "Location of first row in tiered seating", GH_ParamAccess.item)
pManager.AddNumberParameter("First Row Horiz Dist", "FRD", "First row distance from performance boundary", GH_ParamAccess.item)
pManager.AddNumberParameter("First Row Height", "FRH", "First row height above performance boundary", GH_ParamAccess.item)
pManager.AddNumberParameter("C Value", "C", "C value", GH_ParamAccess.item)
pManager.AddNumberParameter("Row Width", "RW", "Row width", GH_ParamAccess.item)
pManager.AddIntegerParameter("Number of Rows", "RN", "Number of Rows", GH_ParamAccess.item)
pManager.AddIntegerParameter("Construction Tolerance", "CT", "Construction Tolerance: 1=1in, 2=1/2in, 4=1/4in, 8=1/8in", GH_ParamAccess.item)
pManager.AddNumberParameter("Max Riser Height", "MR", "Maximum riser height allowed", GH_ParamAccess.item)
pManager.AddGeometryParameter("Spectator", "S", "Seated/Standing spectator", GH_ParamAccess.item)
End Sub
Protected Overrides Sub RegisterOutputParams(pManager As Grasshopper.Kernel.GH_Component.GH_OutputParamManager)
pManager.AddLineParameter("Sightlines", "SL", "Sightlines", GH_ParamAccess.list)
pManager.AddLineParameter("C Value", "CL", "Line represents C value height", GH_ParamAccess.list)
pManager.AddLineParameter("Ground Line", "GL", "Ground Line", GH_ParamAccess.list)
pManager.AddLineParameter("Tier tread", "TR", "Line represents tier treads", GH_ParamAccess.list)
pManager.AddLineParameter("Risers", "RI", "Line represents risers", GH_ParamAccess.list)
pManager.AddGeometryParameter("Spectators", "SP", "Seated Standing Spectators", GH_ParamAccess.list)
End Sub
Protected Overrides Sub SolveInstance(DA As IGH_DataAccess)
Dim newLine As New List(Of Line)
Dim newCValue As New List(Of Line)
Dim rowWidthLineList As New List(Of Line)
Dim floorLineList As New List(Of Line)
Dim riserLineList As New List(Of Line)
Dim leghtList As New List(Of String)
Dim newSeated As New List(Of GeometryBase)
Dim inputPoint As Point3d
If (Not DA.GetData(0, inputPoint)) Then Return
Dim viewPointY As Double
If (Not DA.GetData(1, viewPointY)) Then Return
Dim viewPointZ As Double
If (Not DA.GetData(2, viewPointZ)) Then Return
Dim firstRowPoint As Point3d
If (Not DA.GetData(3, firstRowPoint)) Then Return
Dim firstRowY As Double
If (Not DA.GetData(4, firstRowY)) Then Return
Dim firstRowZ As Double
If (Not DA.GetData(5, firstRowZ)) Then Return
Dim cValue As Double
If (Not DA.GetData(6, cValue)) Then Return
Dim rowWidth As Double
If (Not DA.GetData(7, rowWidth)) Then Return
Dim numberOfRows As Integer
If (Not DA.GetData(8, numberOfRows)) Then Return
Dim M As Integer
If (Not DA.GetData(9, M)) Then Return
Dim maxHeight As Double
If (Not DA.GetData(10, maxHeight)) Then Return
Dim seated As GeometryBase
If (Not DA.GetData(11, seated)) Then Return
Call addNewRow(newLine, newCValue, inputPoint, viewPointY, viewPointZ, firstRowPoint, firstRowY, firstRowZ, cValue, numberOfRows, rowWidth, rowWidthLineList, floorLineList, riserLineList, M, maxHeight, seated, newSeated)
DA.SetDataList(0, newLine)
DA.SetDataList(1, newCValue)
DA.SetDataList(2, rowWidthLineList)
DA.SetDataList(3, floorLineList)
DA.SetDataList(4, riserLineList)
DA.SetDataList(5, newSeated)
End Sub
Public Sub addNewRow(---constructor----)
---additional code----
end Sub…
rested in specializing in the field of Computational design.
The workshop will help understand how Grasshopper facilitates during the design process allowing one to Generate, Automate and Manipulate data.
To Register:
Mail us at intofablab@gmail.com
Workshop Structure:
Day 01: 11 February 2019
Introduction to Computational Processes in Architecture
Understanding Grasshopper and its relation to Rhino3D
Working with fields and Grids (Supplementary readings for Architectural theory)
Spatial Concepts using Data
Day 02: 12 February 2019
Understanding Data in Grasshopper - LISTS
Managing Data in Grasshopper (Supplementary reading)
Experimentation on Massing and Architectural Forms
Day 03: 13 February 2019
Understanding Data in Grasshopper – Trees
Surface Logics (Supplementary reading)
Design Exercise and Prototyping
Day 04: 14 February 2019
Architectural Skins
Day 05: 15 February 2019
MasterClass Project
Introduction to various types of Digital Fabrications
Prototyping of works during the Workshops
Basic knowledge of Rhino 5 is required to be able to take this training.
CERTIFICATION: All participants will receive a Workshop certificate from Authorized Rhino Trainer.
3D Printing: Prototyping of works during the Workshops
Workshop Tutor:
Kavitha M, an Architect and Computational Designer, 3D Printing Specialist is also the co-founder of INTO Design Research, will head the Computational Process in Architecture using Grasshopper workshop. Graduated from Stadelschule Architecture class with Masters in Advanced Architecture Design, has been researching on teaching methodologies on digital tools and their influence on Design thinking.…
The PC actually stops working because after a few seconds the simulation starts the fan inside the PC all of a sudden stops and for the next 5-10 mins I cannot do anything, even alt+ctrl+canc. After I wait for that time i get the followig error:
the ReadMe says:
{0;0;0}0. Grid-based Radiance simulation1. The component is checking ad, as, ar and aa values. This is just to make sure that the results are accurate enough.2. -ar is set to 300.3. Good to go!4. Current working directory is set to: C:\Users\Luigi\Desktop\Prova__\Prova_1\gridBasedSimulation\5. Found a trans material... Resetting st parameter from 0.85 to 0.011276004966. WMIC PROCESS get Commandline7. WMIC PROCESS get Commandline8. WMIC PROCESS get Commandline9. WMIC PROCESS get Commandline10. WMIC PROCESS get Commandline11. WMIC PROCESS get Commandline12. WMIC PROCESS get Commandline13. WMIC PROCESS get Commandline14. WMIC PROCESS get Commandline15. WMIC PROCESS get Commandline16. WMIC PROCESS get Commandline17. WMIC PROCESS get Commandline18. WMIC PROCESS get Commandline19. WMIC PROCESS get Commandline20. WMIC PROCESS get Commandline21. WMIC PROCESS get Commandline22. WMIC PROCESS get Commandline23. WMIC PROCESS get Commandline24. WMIC PROCESS get Commandline25. WMIC PROCESS get Commandline26. WMIC PROCESS get Commandline27. WMIC PROCESS get Commandline28. WMIC PROCESS get Commandline29. WMIC PROCESS get Commandline30. WMIC PROCESS get Commandline31. WMIC PROCESS get Commandline32. WMIC PROCESS get Commandline33. WMIC PROCESS get Commandline34. WMIC PROCESS get Commandline35. WMIC PROCESS get Commandline36. WMIC PROCESS get Commandline37. WMIC PROCESS get Commandline38. WMIC PROCESS get Commandline39. WMIC PROCESS get Commandline40. WMIC PROCESS get Commandline41. WMIC PROCESS get Commandline42. WMIC PROCESS get Commandline43. WMIC PROCESS get Commandline44. WMIC PROCESS get Commandline45. WMIC PROCESS get Commandline46. WMIC PROCESS get Commandline47. WMIC PROCESS get Commandline48. WMIC PROCESS get Commandline49. WMIC PROCESS get Commandline50. WMIC PROCESS get Commandline51. WMIC PROCESS get Commandline52. WMIC PROCESS get Commandline53. WMIC PROCESS get Commandline54. WMIC PROCESS get Commandline55. WMIC PROCESS get Commandline56. WMIC PROCESS get Commandline57. WMIC PROCESS get Commandline58. WMIC PROCESS get Commandline59. WMIC PROCESS get Commandline60. WMIC PROCESS get Commandline61. WMIC PROCESS get Commandline62. WMIC PROCESS get Commandline63. WMIC PROCESS get Commandline64. WMIC PROCESS get Commandline65. WMIC PROCESS get Commandline66. WMIC PROCESS get Commandline67. WMIC PROCESS get Commandline68. WMIC PROCESS get Commandline69. WMIC PROCESS get Commandline70. WMIC PROCESS get Commandline71. WMIC PROCESS get Commandline72. WMIC PROCESS get Commandline73. WMIC PROCESS get Commandline74. WMIC PROCESS get Commandline75. WMIC PROCESS get Commandline76. WMIC PROCESS get Commandline77. WMIC PROCESS get Commandline78. WMIC PROCESS get Commandline79. WMIC PROCESS get Commandline80. WMIC PROCESS get Commandline81. WMIC PROCESS get Commandline82. WMIC PROCESS get Commandline83. WMIC PROCESS get Commandline84. WMIC PROCESS get Commandline85. WMIC PROCESS get Commandline86. WMIC PROCESS get Commandline87. WMIC PROCESS get Commandline88. WMIC PROCESS get Commandline89. WMIC PROCESS get Commandline90. WMIC PROCESS get Commandline91. WMIC PROCESS get Commandline92. WMIC PROCESS get Commandline93. WMIC PROCESS get Commandline94. WMIC PROCESS get Commandline95. WMIC PROCESS get Commandline96. WMIC PROCESS get Commandline97. WMIC PROCESS get Commandline98. WMIC PROCESS get Commandline99. WMIC PROCESS get Commandline100. WMIC PROCESS get Commandline101. WMIC PROCESS get Commandline102. WMIC PROCESS get Commandline103. WMIC PROCESS get Commandline104. WMIC PROCESS get Commandline105. WMIC PROCESS get Commandline106. WMIC PROCESS get Commandline107. WMIC PROCESS get Commandline108. WMIC PROCESS get Commandline109. WMIC PROCESS get Commandline110. WMIC PROCESS get Commandline111. WMIC PROCESS get Commandline112. WMIC PROCESS get Commandline113. WMIC PROCESS get Commandline114. WMIC PROCESS get Commandline115. WMIC PROCESS get Commandline116. WMIC PROCESS get Commandline117. WMIC PROCESS get Commandline118. WMIC PROCESS get Commandline119. WMIC PROCESS get Commandline120. WMIC PROCESS get Commandline121. WMIC PROCESS get Commandline122. WMIC PROCESS get Commandline123. WMIC PROCESS get Commandline124. WMIC PROCESS get Commandline125. WMIC PROCESS get Commandline126. WMIC PROCESS get Commandline127. WMIC PROCESS get Commandline128. WMIC PROCESS get Commandline129. WMIC PROCESS get Commandline130. WMIC PROCESS get Commandline131. WMIC PROCESS get Commandline132. WMIC PROCESS get Commandline133. WMIC PROCESS get Commandline134. WMIC PROCESS get Commandline135. WMIC PROCESS get Commandline136. WMIC PROCESS get Commandline137. WMIC PROCESS get Commandline138. WMIC PROCESS get Commandline139. WMIC PROCESS get Commandline140. WMIC PROCESS get Commandline141. WMIC PROCESS get Commandline142. WMIC PROCESS get Commandline143. WMIC PROCESS get Commandline144. WMIC PROCESS get Commandline145. WMIC PROCESS get Commandline146. WMIC PROCESS get Commandline147. WMIC PROCESS get Commandline148. WMIC PROCESS get Commandline149. WMIC PROCESS get Commandline150. WMIC PROCESS get Commandline151. WMIC PROCESS get Commandline152. WMIC PROCESS get Commandline153. WMIC PROCESS get Commandline154. WMIC PROCESS get Commandline155. WMIC PROCESS get Commandline156. WMIC PROCESS get Commandline157. WMIC PROCESS get Commandline158. WMIC PROCESS get Commandline159. WMIC PROCESS get Commandline160. WMIC PROCESS get Commandline161. WMIC PROCESS get Commandline162. WMIC PROCESS get Commandline163. WMIC PROCESS get Commandline164. WMIC PROCESS get Commandline165. WMIC PROCESS get Commandline166. WMIC PROCESS get Commandline167. WMIC PROCESS get Commandline168. WMIC PROCESS get Commandline169. WMIC PROCESS get Commandline170. WMIC PROCESS get Commandline171. WMIC PROCESS get Commandline172. WMIC PROCESS get Commandline173. WMIC PROCESS get Commandline174. WMIC PROCESS get Commandline175. WMIC PROCESS get Commandline176. WMIC PROCESS get Commandline177. WMIC PROCESS get Commandline178. WMIC PROCESS get Commandline179. WMIC PROCESS get Commandline180. WMIC PROCESS get Commandline181. WMIC PROCESS get Commandline182. WMIC PROCESS get Commandline183. WMIC PROCESS get Commandline184. WMIC PROCESS get Commandline185. WMIC PROCESS get Commandline186. WMIC PROCESS get Commandline187. WMIC PROCESS get Commandline188. WMIC PROCESS get Commandline189. WMIC PROCESS get Commandline190. WMIC PROCESS get Commandline191. WMIC PROCESS get Commandline192. WMIC PROCESS get Commandline193. WMIC PROCESS get Commandline194. WMIC PROCESS get Commandline195. WMIC PROCESS get Commandline196. WMIC PROCESS get Commandline197. WMIC PROCESS get Commandline198. Runtime error (IndexOutOfRangeException): index out of range: 0199. Traceback: line 320, in script
The thing is that if I raise the -aa parameter from 0.05 to 0.1 all works fine..
Is this only related to my PC then?? What should I do to solve this issue?
Thanks again for your help
Luigi…
[2 of 8] No context surfaces...5. [3 of 8] Writing geometry...6. [4 of 8] Writing Electric Load Center - Generator specifications ...7. [5 of 8] Writing materials and constructions...8. [6 of 8] Writing schedules...9. [7 of 8] Writing loads and ideal air system...10. [8 of 8] Writing outputs...11. ...... idf file is successfully written to : C:\Users\Personal\Desktop\TESI\x006\THOR001\EnergyPlus\THOR001.idf12. 13. Analysis is running!...14. C:\Users\Personal\Desktop\TESI\x006\THOR001\EnergyPlus\eplusout.csv15. ......
Done! Read below for errors and warnings:
16. 17. Program Version,EnergyPlus, Version 8.3.0-6d97d074ea, YMD=2016.01.17 17:56,IDD_Version 8.3.018. 19. ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.20. 21. ************* Beginning Zone Sizing Calculations22. 23. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)24. 25. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00126. 27. ** ~~~ ** because vertex 1 of back surface=PELLE_NORD1 is in front of receiving surface=PELLE_COMUNIONE00128. 29. ** ~~~ ** (Dot Product indicator=184.4593)30. 31. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.32. 33. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)34. 35. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00136. 37. ** ~~~ ** because vertex 2 of back surface=PELLE_NORD1 is in front of receiving surface=PELLE_COMUNIONE00138. 39. ** ~~~ ** (Dot Product indicator=184.4593)40. 41. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.42. 43. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)44. 45. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00146. 47. ** ~~~ ** because vertex 3 of back surface=PELLE_NORD1 is in front of receiving surface=PELLE_COMUNIONE00148. 49. ** ~~~ ** (Dot Product indicator=184.4593)50. 51. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.52. 53. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)54. 55. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00156. 57. ** ~~~ ** because vertex 4 of back surface=PELLE_NORD1 is in front of receiving surface=PELLE_COMUNIONE00158. 59. ** ~~~ ** (Dot Product indicator=184.4593)60. 61. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.62. 63. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)64. 65. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00166. 67. ** ~~~ ** because vertex 1 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE00168. 69. ** ~~~ ** (Dot Product indicator=184.4593)70. 71. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.72. 73. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)74. 75. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00176. 77. ** ~~~ ** because vertex 2 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE00178. 79. ** ~~~ ** (Dot Product indicator=184.4593)80. 81. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.82. 83. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)84. 85. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00186. 87. ** ~~~ ** because vertex 3 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE00188. 89. ** ~~~ ** (Dot Product indicator=184.4593)90. 91. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.92. 93. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)94. 95. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00196. 97. ** ~~~ ** because vertex 4 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE00198. 99. ** ~~~ ** (Dot Product indicator=184.4593)100. 101. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.102. 103. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)104. 105. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001106. 107. ** ~~~ ** because vertex 1 of back surface=PELLE_COMUNIONE002 is in front of receiving surface=PELLE_COMUNIONE001108. 109. ** ~~~ ** (Dot Product indicator=184.4593)110. 111. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.112. 113. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)114. 115. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001116. 117. ** ~~~ ** because vertex 2 of back surface=PELLE_COMUNIONE002 is in front of receiving surface=PELLE_COMUNIONE001118. 119. ** ~~~ ** (Dot Product indicator=184.4593)120. 121. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.122. 123. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)124. 125. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001126. 127. ** ~~~ ** because vertex 1 of back surface=WIN_006_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001128. 129. ** ~~~ ** (Dot Product indicator=182.6148)130. 131. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.132. 133. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)134. 135. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001136. 137. ** ~~~ ** because vertex 2 of back surface=WIN_006_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001138. 139. ** ~~~ ** (Dot Product indicator=92.2297)140. 141. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.142. 143. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)144. 145. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001146. 147. ** ~~~ ** because vertex 3 of back surface=WIN_006_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001148. 149. ** ~~~ ** (Dot Product indicator=92.2297)150. 151. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.152. 153. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)154. 155. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001156. 157. ** ~~~ ** because vertex 1 of back surface=WIN_006_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001158. 159. ** ~~~ ** (Dot Product indicator=182.6148)160. 161. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.162. 163. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)164. 165. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001166. 167. ** ~~~ ** because vertex 2 of back surface=WIN_006_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001168. 169. ** ~~~ ** (Dot Product indicator=92.2297)170. 171. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.172. 173. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)174. 175. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001176. 177. ** ~~~ ** because vertex 3 of back surface=WIN_006_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001178. 179. ** ~~~ ** (Dot Product indicator=182.6148)180. 181. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.182. 183. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)184. 185. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001186. 187. ** ~~~ ** because vertex 1 of back surface=WIN_006_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001188. 189. ** ~~~ ** (Dot Product indicator=92.2297)190. 191. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.192. 193. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)194. 195. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001196. 197. ** ~~~ ** because vertex 2 of back surface=WIN_006_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001198. 199. ** ~~~ ** (Dot Product indicator=1.8446)200. 201. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.202. 203. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)204. 205. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001206. 207. ** ~~~ ** because vertex 3 of back surface=WIN_006_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001208. 209. ** ~~~ ** (Dot Product indicator=1.8446)210. 211. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.212. 213. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)214. 215. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001216. 217. ** ~~~ ** because vertex 1 of back surface=WIN_006_GLZP_3 is in front of receiving surface=PELLE_COMUNIONE001218. 219. ** ~~~ ** (Dot Product indicator=92.2297)220. 221. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.222. 223. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)224. 225. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001226. 227. ** ~~~ ** because vertex 2 of back surface=WIN_006_GLZP_3 is in front of receiving surface=PELLE_COMUNIONE001228. 229. ** ~~~ ** (Dot Product indicator=1.8446)230. 231. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.232. 233. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)234. 235. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001236. 237. ** ~~~ ** because vertex 3 of back surface=WIN_006_GLZP_3 is in front of receiving surface=PELLE_COMUNIONE001238. 239. ** ~~~ ** (Dot Product indicator=92.2297)240. 241. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.242. 243. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)244. 245. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001246. 247. ** ~~~ ** because vertex 3 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE001248. 249. ** ~~~ ** (Dot Product indicator=184.4593)250. 251. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.252. 253. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)254. 255. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001256. 257. ** ~~~ ** because vertex 4 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE001258. 259. ** ~~~ ** (Dot Product indicator=184.4593)260. 261. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.262. 263. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)264. 265. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001266. 267. ** ~~~ ** because vertex 1 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE001268. 269. ** ~~~ ** (Dot Product indicator=184.4593)270. 271. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.272. 273. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)274. 275. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001276. 277. ** ~~~ ** because vertex 2 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE001278. 279. ** ~~~ ** (Dot Product indicator=184.4593)280. 281. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.282. 283. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)284. 285. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001286. 287. ** ~~~ ** because vertex 1 of back surface=WIN_001_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001288. 289. ** ~~~ ** (Dot Product indicator=180.7210)290. 291. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.292. 293. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)294. 295. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001296. 297. ** ~~~ ** because vertex 3 of back surface=WIN_001_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001298. 299. ** ~~~ ** (Dot Product indicator=180.7210)300. 301. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.302. 303. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)304. 305. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001306. 307. ** ~~~ ** because vertex 2 of back surface=WIN_001_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001308. 309. ** ~~~ ** (Dot Product indicator=180.7210)310. 311. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.312. 313. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)314. 315. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001316. 317. ** ~~~ ** because vertex 3 of back surface=WIN_001_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001318. 319. ** ~~~ ** (Dot Product indicator=180.7210)320. 321. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.322. 323. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)324. 325. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001326. 327. ** ~~~ ** because vertex 3 of back surface=PELLE_OVEST is in front of receiving surface=PELLE_COMUNIONE001328. 329. ** ~~~ ** (Dot Product indicator=184.4593)330. 331. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.332. 333. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)334. 335. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001336. 337. ** ~~~ ** because vertex 4 of back surface=PELLE_OVEST is in front of receiving surface=PELLE_COMUNIONE001338. 339. ** ~~~ ** (Dot Product indicator=184.4593)340. 341. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.342. 343. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)344. 345. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001346. 347. ** ~~~ ** because vertex 1 of back surface=WIN_002_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001348. 349. ** ~~~ ** (Dot Product indicator=180.7210)350. 351. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.352. 353. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)354. 355. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001356. 357. ** ~~~ ** because vertex 3 of back surface=WIN_002_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001358. 359. ** ~~~ ** (Dot Product indicator=180.7210)360. 361. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.362. 363. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)364. 365. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001366. 367. ** ~~~ ** because vertex 2 of back surface=WIN_002_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001368. 369. ** ~~~ ** (Dot Product indicator=180.7210)370. 371. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.372. 373. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)374. 375. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001376. 377. ** ~~~ ** because vertex 1 of back surface=WIN_002_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001378. 379. ** ~~~ ** (Dot Product indicator=180.7210)380. 381. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.382. 383. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)384. 385. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001386. 387. ** ~~~ ** because vertex 3 of back surface=PELLE_SOTTO is in front of receiving surface=PELLE_COMUNIONE001388. 389. ** ~~~ ** (Dot Product indicator=184.4593)390. 391. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.392. 393. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)394. 395. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001396. 397. ** ~~~ ** because vertex 4 of back surface=PELLE_SOTTO is in front of receiving surface=PELLE_COMUNIONE001398. 399. ** ~~~ ** (Dot Product indicator=184.4593)400. 401. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.402. 403. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)404. 405. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001406. 407. ** ~~~ ** because vertex 7 of back surface=PELLE_SOTTO is in front of receiving surface=PELLE_COMUNIONE001408. 409. ** ~~~ ** (Dot Product indicator=184.4593)410. 411. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.412. 413. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)414. 415. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001416. 417. ** ~~~ ** because vertex 8 of back surface=PELLE_SOTTO is in front of receiving surface=PELLE_COMUNIONE001418. 419. ** ~~~ ** (Dot Product indicator=184.4593)420. 421. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.422. 423. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)424. 425. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001426. 427. ** ~~~ ** because vertex 1 of back surface=PELLE_SOPRA_DUP is in front of receiving surface=PELLE_COMUNIONE001428. 429. ** ~~~ ** (Dot Product indicator=184.4593)430. 431. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.432. 433. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)434. 435. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001436. 437. ** ~~~ ** because vertex 4 of back surface=PELLE_SOPRA_DUP is in front of receiving surface=PELLE_COMUNIONE001438. 439. ** ~~~ ** (Dot Product indicator=184.4593)440. 441. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.442. 443. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)444. 445. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001446. 447. ** ~~~ ** because vertex 5 of back surface=PELLE_SOPRA_DUP is in front of receiving surface=PELLE_COMUNIONE001448. 449. ** ~~~ ** (Dot Product indicator=184.4593)450. 451. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.452. 453. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)454. 455. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001456. 457. ** ~~~ ** because vertex 8 of back surface=PELLE_SOPRA_DUP is in front of receiving surface=PELLE_COMUNIONE001458. 459. ** ~~~ ** (Dot Product indicator=184.4593)460. 461. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.462. 463. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)464. 465. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001466. 467. ** ~~~ ** because vertex 1 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE002468. 469. ** ~~~ ** (Dot Product indicator=167.5695)470. 471. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.472. 473. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)474. 475. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001476. 477. ** ~~~ ** because vertex 2 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE002478. 479. ** ~~~ ** (Dot Product indicator=167.5695)480. 481. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.482. 483. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)484. 485. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001486. 487. ** ~~~ ** because vertex 3 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE002488. 489. ** ~~~ ** (Dot Product indicator=195.1092)490. 491. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.492. 493. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)494. 495. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001496. 497. ** ~~~ ** because vertex 4 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE002498. 499. ** ~~~ ** (Dot Product indicator=195.1092)500. 501. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.502. 503. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)504. 505. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001506. 507. ** ~~~ ** because vertex 3 of back surface=PELLE_COMUNIONE001 is in front of receiving surface=PELLE_COMUNIONE002508. 509. ** ~~~ ** (Dot Product indicator=167.5695)510. 511. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.512. 513. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)514. 515. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001516. 517. ** ~~~ ** because vertex 4 of back surface=PELLE_COMUNIONE001 is in front of receiving surface=PELLE_COMUNIONE002518. 519. ** ~~~ ** (Dot Product indicator=167.5695)520. 521. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.522. 523. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)524. 525. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001526. 527. ** ~~~ ** because vertex 1 of back surface=WIN_005 is in front of receiving surface=PELLE_COMUNIONE002528. 529. ** ~~~ ** (Dot Product indicator=32.0568)530. 531. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.532. 533. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)534. 535. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001536. 537. ** ~~~ ** because vertex 2 of back surface=WIN_005 is in front of receiving surface=PELLE_COMUNIONE002538. 539. ** ~~~ ** (Dot Product indicator=139.1556)540. 541. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.542. 543. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)544. 545. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001546. 547. ** ~~~ ** because vertex 3 of back surface=WIN_005 is in front of receiving surface=PELLE_COMUNIONE002548. 549. ** ~~~ ** (Dot Product indicator=139.1556)550. 551. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.552. 553. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)554. 555. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001556. 557. ** ~~~ ** because vertex 4 of back surface=WIN_005 is in front of receiving surface=PELLE_COMUNIONE002558. 559. ** ~~~ ** (Dot Product indicator=32.0568)560. 561. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.562. 563. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)564. 565. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001566. 567. ** ~~~ ** because vertex 1 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE002568. 569. ** ~~~ ** (Dot Product indicator=167.5695)570. 571. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.572. 573. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)574. 575. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001576. 577. ** ~~~ ** because vertex 2 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE002578. 579. ** ~~~ ** (Dot Product indicator=167.5695)580. 581. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.582. 583. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)584. 585. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001586. 587. ** ~~~ ** because vertex 3 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE002588. 589. ** ~~~ ** (Dot Product indicator=167.5695)590. 591. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.592. 593. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)594. 595. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001596. 597. ** ~~~ ** because vertex 4 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE002598. 599. ** ~~~ ** (Dot Product indicator=167.5695)600. 601. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.602. 603. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)604. 605. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001606. 607. ** ~~~ ** because vertex 1 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002608. 609. ** ~~~ ** (Dot Product indicator=195.1092)610. 611. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.612. 613. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)614. 615. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001616. 617. ** ~~~ ** because vertex 2 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002618. 619. ** ~~~ ** (Dot Product indicator=195.1092)620. 621. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.622. 623. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)624. 625. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001626. 627. ** ~~~ ** because vertex 3 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002628. 629. ** ~~~ ** (Dot Product indicator=195.1092)630. 631. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.632. 633. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)634. 635. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001636. 637. ** ~~~ ** because vertex 4 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002638. 639. ** ~~~ ** (Dot Product indicator=195.1092)640. 641. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.642. 643. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)644. 645. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001646. 647. ** ~~~ ** because vertex 5 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002648. 649. ** ~~~ ** (Dot Product indicator=195.1092)650. 651. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.652. 653. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)654. [...]
thisthe errorthat appen when i lunch E+ with only one zone....what is going on???? …
ated in all editions of Architektura Parametryczna Workshops!Architektura Parametryczna Workshops Optimization Warsaw 2016 FAQWHEN?21-22nd May 2016 (Saturday-Sunday)HOW LONG DO THE WORKHSOPS LAST?The workshops last in total 16 hours.Saturday 10AM -7PM (with lunch break), Sunday 10AM -7PM (with lunch break)WHAT WILL I LEARN?On Saturday the optimization processes with solar, views and structural analysis will be explored. We will be discovering optimal solutions with the help of plug-ins such as Galapagos, Silvereye, Octopus, Karamba and Ladybug. In the Sunday morning we will learn how to present the results of the optimization: creating catalogues of solutions and printing the optimization graphs. In the afternoon participants will have time for the development of the personal project. HOW MUCH DOES IT COST?The workshops cost 600 PLN (or 160€) for Early Bird payments and 700 PLN (or 190€) for the regular payments. The 3-person group - 1500 PLN (or 440€ )EARLY BIRD?For those who are certain that they will attend the workshops, we have a special Early Bird offer till 30th of April 2016.HOW CAN I SIGN UP?Send an email to info@architekturaparametryczna.pl with the title: “OPTI WAW 16”.HOW MANY PLACES ARE AVAILABLE?We have only 11 places!WORKSHOPS: Level: intermediate – advancePerquisites: the basic knowledge of Rhino and Grasshopper3D. Plug-ins: Silvereye, Octopus, Ladybug, Karamba. Weaverbird. Python GHThe main aim of the 16-hour workshops is to give the participants the understanding of how the optimization process can be used in practice and how it can help in solving everyday design problems. The practical exercise will be supported with the short lectures explaining the theoretical background of the optimization algorithms. The general program of the Optimization Warsaw 2016 Workshops*:1. Optimization of the facade geometry with solar analysis.2. Optimization of the roof structures with Karamba.3. Finding the optimal configuration of the space frame structures with Karamba.4. Discovering the best location or/and geometry of the building in accordance to the best views from the plot.5. Presentation of the discovered solutions. *Some of the exercises might be changed.…