and says "repeat every Nth element", meaning say if N was 3, I would get A B C C D E F F G H. I would also like to be able to then insert a list of 3 elements in between each of the repeats. For example, I wanted to insert: 1. 1
2. 2
3. 3 into the list, I would get A B C 1 2 3 C D E F 1 2 3 F G H. It seems like an easy task, but I cannot for the life of me figure out how to do it, I must be making a very basic mistake. I am new to grasshopper, so any and all help I could get would be GREATLY appreciated!…
have 1 tree with 8 branches and 6 items each.
Weave kinda does it but it order the point wrong as it puts 1 item from each tree and then the remaining 3 items from the middle tree last.
Thank for any help.
…
a follow up question... how do I wrap a list onto itself at a certain frequency?
i.e. I want the list {1;2;3;4;5;6;7;8;9}
to become {1,4,7; 2,6,8; 3,6,9} wrapped every 3rd item
Added by Joshua Jordan at 5:30pm on November 17, 2012
or each branch goes to col 1, element 2 to col 2 and so on. The issue I am having is how to deal with branches that have less than 5 elements. Notice how in the attachment the number 8 is at row 2 where I want it to be in row 3.…
Added by jon kontuly at 1:03pm on September 30, 2014
ture which is combined with some columns. The columns are arranged in a straight grid structure. I’m not able to get a smooth transition between structural curves as you can see in the image.
Problem 1: I was able to make the columns out of 4 curves, I need this to be 8.
Problem 2: I want to be able to manipulate the column posiotions by XYZ.
Problem 3: The curves (these two curves should be a dome like structure) from two columns aren’t conecting smoothly as you can see in the green ellipse in the image below.
After I created the column curves ( blue circle) in grasshopper (file: 'Surface+Columns' and 'columns2') I made solid columns out of it and tryed to join them smoothly with the surface to project a grid structure on it (in rhino).
Unfortunatly I went wrong and the problem is which you can see in the red ellipse:
The column pipes aren’t on the same level like the grid structure of the surface. Somethimes they are on, sometimes under the surface.
Could somebody help me please, That would be absolutly great!! :)
In the file 'Surface' you'll find the Surface with the current column possition.
Here you find a few reference pictures, but actually it should look like on the rendering below - just properly :)
reference1.jpg
reference2.jpg
reference3.jpg
…
NONE, in SIZING:PARAMETERS". I'm not sure of where to start in troubleshooting this. I've attached the file.
Thank you,
See the errors and warnings below:
{0;0;0}
0. Current document units is in Meters
1. Conversion to Meters will be applied = 1.000
2. [1 of 8] Writing simulation parameters...
3. [2 of 8] Writing context surfaces...
4. [2 of 8] Writing context surfaces...
5. [3 of 8] Writing geometry...
6. [4 of 8] Writing Electric Load Center - Generator specifications ...
7. [5 of 8] Writing materials and constructions...
8. [6 of 8] Writing schedules...
9. [7 of 8] Writing loads and ideal air system...
10. [8 of 8] Writing outputs...
11. ...
... idf file is successfully written to : R:\Green\SuRG\Building_Performance_Analysis\2016_analysis_studies\Energy_Analysis_Comparison\Honeybee_+_Ladybug\tutorial01\EnergyPlus\tutorial01.idf
12.
13. Analysis is running!...
14. ...
...
Done! Read below for errors and warnings:
15.
16. Program Version,EnergyPlus, Version 8.5.0-c87e61b44b, YMD=2016.10.31 11:39,IDD_Version 8.5.0
17.
18. ************* IDF Context for following error/warning message:
19.
20. ************* Note -- lines truncated at 300 characters, if necessary...
21.
22. ************* 24 Sizing:Parameters,
23.
24. ************* Only last 1 lines before error line shown.....
25.
26. ************* 25 None, !- Heating Sizing Factor
27.
28. ** Severe ** IP: IDF line~25 Invalid Number in Numeric Field#1 (Heating Sizing Factor), value=NONE, in SIZING:PARAMETERS
29.
30. ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
31.
32. ** ~~~ ** Possible Invalid Numerics or other problems
33.
34. ** Fatal ** IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination.
35.
36. ...Summary of Errors that led to program termination:
37.
38. ..... Reference severe error count=1
39.
40. ..... Last severe error=IP: IDF line~
, value=NONE, in SIZING:PARAMETERS
41.
42. ************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).
43.
44. ************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.
45.
46. ************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
47.
48. ************* EnergyPlus Sizing Error Summary. During Sizing: 0 Warning; 0 Severe Errors.
49.
50. ************* EnergyPlus Terminated--Fatal Error Detected. 1 Warning; 1 Severe Errors; Elapsed Time=00hr 00min 9.34sec
51.…