ceros. Parametrización, panelización y análisis en Grasshopper, así como el proceso de manufactura digital para maquinaria de corte Láser y CNC.
UN solo pago anticipado $4,000.00
Pagos diferidos $4,500.00*
*reserva tu lugar con el 50%
Martes y Jueves de 7 a 10 PM
Del 15 de Mayo al 14 de junio
DURACION: 30 HORAS
SESIONES: 10 DE 3 HORAS
o info@dimensiontallerdigital.com
informes al 55 (50 16 0634) con Mayri Gallegos (o al cel. 55 28 85 24 73)
$4,000.00…
pen Brep"; I didn't know it worked on flat surfaces. And I think it's only fair to include in your benchmark the considerable time 'SUnion' takes in this example: 21.9 seconds for 121 rings and likely much more with 400 or 1,000+ rings.
Then I noticed the pattern doesn't match. Checked the circles and they are the same. The distance between them, however, is different: 7 instead of 6. When I change that value to 6, the Python fails badly. All the holes and gaps are gone, which destroys the pattern:
I can't do the "two phase" approach on an 11 X 11 grid, but I can do 6 X 6 and 2 X 2 to get a 12 X 12 grid (40 'SUnion' operations) in 28 seconds total. That beats your benchmark of ~37 seconds for an 11 X 11 grid, if you include the 'SUnion' in your code.
…
NONE, in SIZING:PARAMETERS". I'm not sure of where to start in troubleshooting this. I've attached the file.
Thank you,
See the errors and warnings below:
{0;0;0}
0. Current document units is in Meters
1. Conversion to Meters will be applied = 1.000
2. [1 of 8] Writing simulation parameters...
3. [2 of 8] Writing context surfaces...
4. [2 of 8] Writing context surfaces...
5. [3 of 8] Writing geometry...
6. [4 of 8] Writing Electric Load Center - Generator specifications ...
7. [5 of 8] Writing materials and constructions...
8. [6 of 8] Writing schedules...
9. [7 of 8] Writing loads and ideal air system...
10. [8 of 8] Writing outputs...
11. ...
... idf file is successfully written to : R:\Green\SuRG\Building_Performance_Analysis\2016_analysis_studies\Energy_Analysis_Comparison\Honeybee_+_Ladybug\tutorial01\EnergyPlus\tutorial01.idf
12.
13. Analysis is running!...
14. ...
...
Done! Read below for errors and warnings:
15.
16. Program Version,EnergyPlus, Version 8.5.0-c87e61b44b, YMD=2016.10.31 11:39,IDD_Version 8.5.0
17.
18. ************* IDF Context for following error/warning message:
19.
20. ************* Note -- lines truncated at 300 characters, if necessary...
21.
22. ************* 24 Sizing:Parameters,
23.
24. ************* Only last 1 lines before error line shown.....
25.
26. ************* 25 None, !- Heating Sizing Factor
27.
28. ** Severe ** IP: IDF line~25 Invalid Number in Numeric Field#1 (Heating Sizing Factor), value=NONE, in SIZING:PARAMETERS
29.
30. ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
31.
32. ** ~~~ ** Possible Invalid Numerics or other problems
33.
34. ** Fatal ** IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination.
35.
36. ...Summary of Errors that led to program termination:
37.
38. ..... Reference severe error count=1
39.
40. ..... Last severe error=IP: IDF line~
, value=NONE, in SIZING:PARAMETERS
41.
42. ************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).
43.
44. ************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.
45.
46. ************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
47.
48. ************* EnergyPlus Sizing Error Summary. During Sizing: 0 Warning; 0 Severe Errors.
49.
50. ************* EnergyPlus Terminated--Fatal Error Detected. 1 Warning; 1 Severe Errors; Elapsed Time=00hr 00min 9.34sec
51.…
29 points vs. 28 points for the 'Base Crv' - not sure what's up with that?
Move the slider in the 'Adjust Seam' group to see parametric design in action!
And just FYI, there are only 12 discontinuity points in the 'Step Crv' so setting the 'Divide Curve' 'Count' slider to 12 looks pretty good to me, except for that extra point.…
Added by Joseph Oster at 12:26pm on January 10, 2016
error message when GH starts loading (almost the last stage of loading).
I un-installed and re-installed it, but still the same error. When I checked the plug-ins in the options, it seems that it is loading the right one (from the file path), but I noticed when GH starts loading, it is loading GH version Sep 28, 2012.
Any idea how I can get around this problem?
thanks
…
ay be loading it from Rhino 4, but even when I un-installed GH for Rhino 4, GH rhino 5 still loading that version. The strange thing is that when I check Tools-options-plug ins, GH -properties it shows the right file name and path of GrasshopperPlugIn.rhp, and the right registry path too that is in Rhino 5 Plug ins. So why on earth it is loading that previous mysterious copy?, and where it can be located?
Any steps I need to follow that may solve the problem?…
Added by Zayad Motlib at 12:02am on March 11, 2013
connection, camera, micro. Rhinoceros software; much better with Windows system.
Materials > Materials, equipments and tools needed for making the prototype are included in the course tuition.
Training hours > 72 hours (Part I) and 28 hours (Part II). It is possible to do the full course or just Part I
Certificate It will be provided a certificate by Authorised Rhino Training Center and Rhino FabStudio Official
Instruction Language > English (or Spanish if all the students speak it)
PART I (On-line) – August 8-26
Schedule: Monday to Friday, 4 - 8pm (Madrid, CET)
PART II, optional (On-site / On-line) August 29 - September 2
Schedule*: Monday - Friday 1- 3pm and 4-8pm (Madrid, CEST)…