NONE, in SIZING:PARAMETERS". I'm not sure of where to start in troubleshooting this. I've attached the file.
Thank you,
See the errors and warnings below:
{0;0;0}
0. Current document units is in Meters
1. Conversion to Meters will be applied = 1.000
2. [1 of 8] Writing simulation parameters...
3. [2 of 8] Writing context surfaces...
4. [2 of 8] Writing context surfaces...
5. [3 of 8] Writing geometry...
6. [4 of 8] Writing Electric Load Center - Generator specifications ...
7. [5 of 8] Writing materials and constructions...
8. [6 of 8] Writing schedules...
9. [7 of 8] Writing loads and ideal air system...
10. [8 of 8] Writing outputs...
11. ...
... idf file is successfully written to : R:\Green\SuRG\Building_Performance_Analysis\2016_analysis_studies\Energy_Analysis_Comparison\Honeybee_+_Ladybug\tutorial01\EnergyPlus\tutorial01.idf
12.
13. Analysis is running!...
14. ...
...
Done! Read below for errors and warnings:
15.
16. Program Version,EnergyPlus, Version 8.5.0-c87e61b44b, YMD=2016.10.31 11:39,IDD_Version 8.5.0
17.
18. ************* IDF Context for following error/warning message:
19.
20. ************* Note -- lines truncated at 300 characters, if necessary...
21.
22. ************* 24 Sizing:Parameters,
23.
24. ************* Only last 1 lines before error line shown.....
25.
26. ************* 25 None, !- Heating Sizing Factor
27.
28. ** Severe ** IP: IDF line~25 Invalid Number in Numeric Field#1 (Heating Sizing Factor), value=NONE, in SIZING:PARAMETERS
29.
30. ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
31.
32. ** ~~~ ** Possible Invalid Numerics or other problems
33.
34. ** Fatal ** IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination.
35.
36. ...Summary of Errors that led to program termination:
37.
38. ..... Reference severe error count=1
39.
40. ..... Last severe error=IP: IDF line~
, value=NONE, in SIZING:PARAMETERS
41.
42. ************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).
43.
44. ************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.
45.
46. ************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
47.
48. ************* EnergyPlus Sizing Error Summary. During Sizing: 0 Warning; 0 Severe Errors.
49.
50. ************* EnergyPlus Terminated--Fatal Error Detected. 1 Warning; 1 Severe Errors; Elapsed Time=00hr 00min 9.34sec
51.…
.. but I have a graph in mind about how i want to numbers,..First 100 numbers have to only range between 0-5, then 100-140 number have to gradually increase from 0 - 20 and back 20 - 0, and then 140 - 200 numbers have to again only range from 0-5,..So basically the graph looks like almost a straight line from 0 - 100, then the graph has to gradually raise till 20 and falls down to 0 inbetween 100-140, and then again it will be a straight line from 140 - 200,..So is there a way that i can achieve such custom graph in the graphmapper component,..??? I want to achieve movements only in particular regions in the graph, how can i get that,..?Thanks…
SiTI - Politecnico di Torino + ETH Computational Assessment Workshop at ETH - ValueLab - March 20, 2012 Assessment of 3 scenarios on the development of the F...
uld be much better than Rhino at huge mesh collections. I'd personally try free Autodesk Meshmixer and ZBrush first but most designers are more familiar with rendering programs like Maya or 3DS Max. I'm not familiar enough with architecture to suggest a list as only Revit and Sketchup come to mind.
Looking more closely, CAD Exporter is only for 2D curves and points, how silly, and it requires baked geometry in a Rhino layer:
I could write a Python script to export an STL but that would be a large ascii format file instead of binary. Better to use OBJ to retain quad faces, too.
Ah, well, OBJ files are also ascii format when exported from Rhino, so it would be quite easy to make a script to export those directly to disk from Grasshopper. Here is one box, 10X10X20 in size, with quad faces:
# Rhino
o object_1v 10 10 20v 10 10 0v 10 0 20v 10 0 0v 0 10 20v 0 10 0v 0 0 20v 0 0 0f 5 7 3 1f 5 6 8 7f 3 7 8 4f 2 4 8 6f 5 1 2 6f 3 4 2 1
If I have time I'll make a little script to write such OBJ files unless you can find a native Grasshopper plugin for direct OBJ export in full 3D for meshes.…
our question about conway operators for what I think is the most robust way!
To answer your second question, assuming your plankton mesh has existing vertices, you need to specify the indices of the new vertices when adding the face. Thankfully PlanktonMesh.Vertices.Add() returns the index of the newly added vertex, so you could modify your code, like so...
v0 = PMesh.Vertices.Add(0, 0, 0) v1 = PMesh.Vertices.Add(20, 0, 0) v2 = PMesh.Vertices.Add(20, 20, 0) v3 = PMesh.Vertices.Add(0, 20, 0) PMesh.Faces.AddFace(v0, v1, v2, v3)
I posted some very rough documention a while ago... Please let me know if you have any ideas for how this could be clearer!…