oo culm and the web is mad of bamboo slats connected to the culms on either side of the attachment points. To make things clearer (extracted from the above paper):
The authors of the paper did a numerical beam-model in ANSYS to see if they could replicate their theoretical results, and it is fairly correct (some differences due to the non-linear behavior of the semi-ring joints that they use, they remain of an order of 5-10% difference in maximum deflection).
My problem is that I am not able to obtain the same deflection values that the authors did (11.4 mm for a total service load of 7.063 kN applied punctually on the upper chord where the truss elements meet, or even replicate the load/deflection curve). Using an orthotropic material, with the engineering constants taken from (ResearchGate - A bamboo Beam-Column Connection Capable to Transmit Moment), my model is too flexible and I get a maximum deflection of 24.28 mm. I tried other orthotropic mechanical characterizations from other sources (Kathry & Mishra, 2012, Finite element analysis of bamboo and joints using steel members under various loading conditions for design study and Chand , Shukla & Sharma, 2008, Analysis of Mechanical Behaviour of Bamboo (Dendrocalamus strictus) by Using FEM), to no avail.
Of course, the problem could be with the material properties I inputted but I am trying to contact the research team to see directly with them. In the meantime, I am looking to make sure the model itself is not flawed.
It also seems to me that gravity was not accounted for in the numerical of the paper, but it seemed to much of an oversight to be possible (still, the deflection curve of their paper goes through 0).
There are several points I am not quite sure about: after all I am still fairly new to Karamba3D and may still have some things to learn about the inner mechanics of the plugin.
The very first is: should I put eccentricities of the slat-elements of the truss in the definition of their cross-section (directly with the Cross Section box) or as an offset of the beam element (with the ModifyElem box)? I tried both approaches and they seem to yield similar results (max. deflection change by 0.65mm in my latest model).
Second is: is it good practice to subdivide the beam elements in more than one element (and connecting the pieces rigidly) in order to get better results? I imagine some meshing or subdivision is performed when the analysis is run but there is no way of visualizing it (that I found in any case). Subdividing the chord elements seems to give smoother deformation results (though I did not check stress I have to admit). My issue on this topic is that the subdivision of the slat-elements of the web is problematic. On the screenshot below, where the elements are divided in two, lets take the example of node 18. It seems to me that all elements of the diagonal element (28, 29, 34 & 35) are all rigidly connected to the node 18. 28 & 29 are not connected together, independently from 34 & 35. The added rigidity may not be a bad thing for my model, but it is not correct I think? Is there a way of solving the problem?
Element tags:
Node tags:
And here is my GH file (clean enough hopefully): verification-model-V04.gh
Thank you all in advance for any insight (even on the inner logics of Karamba)!
…
a conceptualización de un proceso paramétrico, el uso de algoritmos como herramienta creativa, técnicas de generación formal avanzada, y métodos para la optimización y mejora de nuestros diseños.
El énfasis se hará sobre estos conceptos, a la vez que haremos un uso exhaustivo de herramientas específicas de modelado generativo para materializar estas ideas, en nuestro caso, Rhinoceros y Grasshopper.
En ParametricCamp nos gusta ponernos manos a la obra. Habrá teoría, estudios, debate y puestas en común, pero principalmente trabajaremos, programaremos y produciremos sobre ejemplos prácticos y modelos concretos, estructurados con una complejidad creciente y desarrollados con fines docentes. Así mismo, el evento finalizará con un proyecto personal, de programa flexible adaptado a tus intereses particulares, y desarrollado a lo largo del taller.
ParametricCamp es abierto y multidisciplinar, y está orientado a estudiantes y profesionales del campo del diseño, y en especial de la arquitectura y el diseño industrial.
ParametricCamp estará en:
ParametricCamp SEVILLA 2011
Fecha: del 18 al 22 de Julio
ParametricCamp GRANADA 2011
Fecha: del 25 al 29 de Julio
ParametricCamp MÁLAGA 2011
Fecha: del 1 al 5 de Agosto
…
ll learn the essential skills of manipulating geometry using various computational methods. The workshop will specifically demonstrate how to control the performance related data flow from Autodesk Ecotect, Vasari and Maya into the parametric modeling environment of Grassshopper; how to generate complex 2D/3D patterns based on the abstract relationship among points, lines and surfaces; how to integrate Rhino’s surface modeling with Maya’s mesh modeling; how to use performance data baked from other program as the driver to manipulate adaptive geometries across the building skin.
Lecture Topics
Parametric design concepts
Computation for Performance Driven Design
Morphing geometry and biomimicry
Surfaces and meshes
Demonstrations
Image based tessellation
Pattern making
Paneling with adaptive objects
Box morphing and variations
Vertex color based object morphing, integrating Maya with Grasshopper
Geometry manipulation based on the solar data from Ecotect and Vasari
Dates - July 10, 2012 : Workshop Announced + Registration Opens. - August 15, 2012 : Registration Closes. - August 18 &19, 2012: Workshop.
Check more detail online
…
ment.
This course will help architects and designers in their practice and development of forms using generative algorithms.
Curriculum
Introduction to parametric design
Understanding the user interface of Grasshopper and visual programming theory
Understand the components and types of networking
Linking and importing and exporting geometry from Rhino Rhino geometry results back
Knowledge of the main data types (numbers, fields, vectors, points, curves, surfaces, brep)
Manage lists and trees of data: simple tasks lists, extracting data in lists and trees
Operations with vectors and points
Using colored gradient according to the parameters
Strategies of planar space subdivision: Voronoi
Working with curves and create surfaces : loft, surface from points, attractors
Surface subdivision with Lunchbox: triangular, hex, diagrid
Schedule:
Module Grasshopper beginners (24 h)
10 May – 24 May 2014
Sat:
9 - 13
14 - 18
Language: Romanian
Trainers:
Ionuț Anton, idz arhitectura (ART-Authorised Rhino Trainer)
Dana Tănase, idz arhitectura (ART-Authorised Rhino Trainer)
https://www.facebook.com/cursurigrasshopperrhinoceros
https://www.facebook.com/idzarhitectura
http://www.idz.ro/training/…
Added by Dana Tanase at 2:21am on February 2, 2014
P) Il corso offrirà le basi per la modellazione parametrica attraverso l’interfaccia generativa Grasshopper, plug-in del noto modellatore nurbs, Rhinoceros. Attraverso una serie di esercizi che si svolgeranno durante il corso, si spiegheranno i temi fondamentali che stanno alla base della modellazione generativa e del design parametrico. Docente Leonidas Paterakis. Il corso è rivolto a chi ha già una familiarità minima con la modellazione attraverso Rhinoceros e vuole ampliare le proprie competenze verso il campo della modellazione parametrica e generativa, e si terrà da martedì 18.04.2017 a giovedì 20.04.2017 – dalle 10:00 alle 17:00. VEGA Parco Scientifico Tecnologico Via della Libertà 12 – Venezia Edificio Porta dell’Innovazione – Piano Terra Le iscrizioni chiuderanno giovedì 13.04.2017. Il corso ha un costo di 270,00 euro + iva (329.40) per i tesserati e convenzionati, per i non tesserati il costo sarà di 330,00 + iva (402.60) euro. Per informazioni e iscrizioni:
http://www.fablabvenezia.org/parametric-design-with-grasshopper/…
atch Online HD 21st Dec 2017. Yeh Hai Mohabbatein 21st December 2017 Watch Online HD 21st Dec 2017. Yeh Hai Mohabbatein 21st December 2017 - Batameezdil Full EpisodeYeh Hai Mohabbatein 21st December 2017 Watch Online, Today Replay Yeh Hai Mohabbatein 21st December 2017 On Star Plus. Indian Drama Series Yeh Hai Mohabbatein 21 Dec 2017 In Hd Quality Full Part. Yeh Hai Mohabbatein 21st December 2017 Today Replay Recap Youtube Video. Yeh Hai Mohabbatein 21st ...Yeh Hai Mohabbatein 21st December 2017 Full Episode 1355 - VideoVideo watch online Yeh Hai Mohabbatein 21st December 2017 full Episode 1355 of Star Plus drama serial Yeh Hai Mohabbatein complete show episodes.Yeh Hai Mohabbatein 21st December 2017 DEC 21 2017 LIVE WATCH NOW ...- Yeh Hai Mohabbatein 21st December 2017 Full Episode Watch Online Dec 21 …Yeh Hai Mohabbatein 21st December 2017 Full Episode Colors Tv HD. Hotstar Yeh Hai Mohabbatein Episode full by Colors Tv.Watch Yeh Hai Mohabbatein 21st December 2017 Video Online.Yeh Hai Mohabbatein 21st ...Watch Ye Hai Mohabbatein Full Episodes Online, Streaming ... - HotstarWatch Ye Hai Mohabbatein latest & full episodes online on hotstar. Upgrade to premium membership to enjoy all the latest award winning Undefined TV shows instantly & ad-free in HD on hotstar!…
[2 of 8] No context surfaces...5. [3 of 8] Writing geometry...6. [4 of 8] Writing Electric Load Center - Generator specifications ...7. [5 of 8] Writing materials and constructions...8. [6 of 8] Writing schedules...9. [7 of 8] Writing loads and ideal air system...10. [8 of 8] Writing outputs...11. ...... idf file is successfully written to : C:\Users\Personal\Desktop\TESI\x006\THOR001\EnergyPlus\THOR001.idf12. 13. Analysis is running!...14. C:\Users\Personal\Desktop\TESI\x006\THOR001\EnergyPlus\eplusout.csv15. ......
Done! Read below for errors and warnings:
16. 17. Program Version,EnergyPlus, Version 8.3.0-6d97d074ea, YMD=2016.01.17 17:56,IDD_Version 8.3.018. 19. ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.20. 21. ************* Beginning Zone Sizing Calculations22. 23. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)24. 25. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00126. 27. ** ~~~ ** because vertex 1 of back surface=PELLE_NORD1 is in front of receiving surface=PELLE_COMUNIONE00128. 29. ** ~~~ ** (Dot Product indicator=184.4593)30. 31. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.32. 33. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)34. 35. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00136. 37. ** ~~~ ** because vertex 2 of back surface=PELLE_NORD1 is in front of receiving surface=PELLE_COMUNIONE00138. 39. ** ~~~ ** (Dot Product indicator=184.4593)40. 41. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.42. 43. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)44. 45. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00146. 47. ** ~~~ ** because vertex 3 of back surface=PELLE_NORD1 is in front of receiving surface=PELLE_COMUNIONE00148. 49. ** ~~~ ** (Dot Product indicator=184.4593)50. 51. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.52. 53. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)54. 55. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00156. 57. ** ~~~ ** because vertex 4 of back surface=PELLE_NORD1 is in front of receiving surface=PELLE_COMUNIONE00158. 59. ** ~~~ ** (Dot Product indicator=184.4593)60. 61. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.62. 63. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)64. 65. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00166. 67. ** ~~~ ** because vertex 1 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE00168. 69. ** ~~~ ** (Dot Product indicator=184.4593)70. 71. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.72. 73. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)74. 75. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00176. 77. ** ~~~ ** because vertex 2 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE00178. 79. ** ~~~ ** (Dot Product indicator=184.4593)80. 81. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.82. 83. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)84. 85. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00186. 87. ** ~~~ ** because vertex 3 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE00188. 89. ** ~~~ ** (Dot Product indicator=184.4593)90. 91. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.92. 93. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)94. 95. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00196. 97. ** ~~~ ** because vertex 4 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE00198. 99. ** ~~~ ** (Dot Product indicator=184.4593)100. 101. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.102. 103. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)104. 105. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001106. 107. ** ~~~ ** because vertex 1 of back surface=PELLE_COMUNIONE002 is in front of receiving surface=PELLE_COMUNIONE001108. 109. ** ~~~ ** (Dot Product indicator=184.4593)110. 111. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.112. 113. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)114. 115. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001116. 117. ** ~~~ ** because vertex 2 of back surface=PELLE_COMUNIONE002 is in front of receiving surface=PELLE_COMUNIONE001118. 119. ** ~~~ ** (Dot Product indicator=184.4593)120. 121. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.122. 123. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)124. 125. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001126. 127. ** ~~~ ** because vertex 1 of back surface=WIN_006_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001128. 129. ** ~~~ ** (Dot Product indicator=182.6148)130. 131. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.132. 133. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)134. 135. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001136. 137. ** ~~~ ** because vertex 2 of back surface=WIN_006_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001138. 139. ** ~~~ ** (Dot Product indicator=92.2297)140. 141. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.142. 143. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)144. 145. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001146. 147. ** ~~~ ** because vertex 3 of back surface=WIN_006_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001148. 149. ** ~~~ ** (Dot Product indicator=92.2297)150. 151. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.152. 153. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)154. 155. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001156. 157. ** ~~~ ** because vertex 1 of back surface=WIN_006_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001158. 159. ** ~~~ ** (Dot Product indicator=182.6148)160. 161. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.162. 163. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)164. 165. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001166. 167. ** ~~~ ** because vertex 2 of back surface=WIN_006_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001168. 169. ** ~~~ ** (Dot Product indicator=92.2297)170. 171. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.172. 173. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)174. 175. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001176. 177. ** ~~~ ** because vertex 3 of back surface=WIN_006_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001178. 179. ** ~~~ ** (Dot Product indicator=182.6148)180. 181. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.182. 183. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)184. 185. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001186. 187. ** ~~~ ** because vertex 1 of back surface=WIN_006_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001188. 189. ** ~~~ ** (Dot Product indicator=92.2297)190. 191. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.192. 193. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)194. 195. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001196. 197. ** ~~~ ** because vertex 2 of back surface=WIN_006_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001198. 199. ** ~~~ ** (Dot Product indicator=1.8446)200. 201. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.202. 203. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)204. 205. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001206. 207. ** ~~~ ** because vertex 3 of back surface=WIN_006_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001208. 209. ** ~~~ ** (Dot Product indicator=1.8446)210. 211. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.212. 213. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)214. 215. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001216. 217. ** ~~~ ** because vertex 1 of back surface=WIN_006_GLZP_3 is in front of receiving surface=PELLE_COMUNIONE001218. 219. ** ~~~ ** (Dot Product indicator=92.2297)220. 221. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.222. 223. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)224. 225. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001226. 227. ** ~~~ ** because vertex 2 of back surface=WIN_006_GLZP_3 is in front of receiving surface=PELLE_COMUNIONE001228. 229. ** ~~~ ** (Dot Product indicator=1.8446)230. 231. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.232. 233. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)234. 235. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001236. 237. ** ~~~ ** because vertex 3 of back surface=WIN_006_GLZP_3 is in front of receiving surface=PELLE_COMUNIONE001238. 239. ** ~~~ ** (Dot Product indicator=92.2297)240. 241. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.242. 243. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)244. 245. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001246. 247. ** ~~~ ** because vertex 3 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE001248. 249. ** ~~~ ** (Dot Product indicator=184.4593)250. 251. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.252. 253. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)254. 255. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001256. 257. ** ~~~ ** because vertex 4 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE001258. 259. ** ~~~ ** (Dot Product indicator=184.4593)260. 261. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.262. 263. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)264. 265. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001266. 267. ** ~~~ ** because vertex 1 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE001268. 269. ** ~~~ ** (Dot Product indicator=184.4593)270. 271. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.272. 273. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)274. 275. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001276. 277. ** ~~~ ** because vertex 2 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE001278. 279. ** ~~~ ** (Dot Product indicator=184.4593)280. 281. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.282. 283. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)284. 285. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001286. 287. ** ~~~ ** because vertex 1 of back surface=WIN_001_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001288. 289. ** ~~~ ** (Dot Product indicator=180.7210)290. 291. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.292. 293. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)294. 295. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001296. 297. ** ~~~ ** because vertex 3 of back surface=WIN_001_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001298. 299. ** ~~~ ** (Dot Product indicator=180.7210)300. 301. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.302. 303. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)304. 305. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001306. 307. ** ~~~ ** because vertex 2 of back surface=WIN_001_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001308. 309. ** ~~~ ** (Dot Product indicator=180.7210)310. 311. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.312. 313. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)314. 315. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001316. 317. ** ~~~ ** because vertex 3 of back surface=WIN_001_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001318. 319. ** ~~~ ** (Dot Product indicator=180.7210)320. 321. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.322. 323. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)324. 325. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001326. 327. ** ~~~ ** because vertex 3 of back surface=PELLE_OVEST is in front of receiving surface=PELLE_COMUNIONE001328. 329. ** ~~~ ** (Dot Product indicator=184.4593)330. 331. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.332. 333. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)334. 335. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001336. 337. ** ~~~ ** because vertex 4 of back surface=PELLE_OVEST is in front of receiving surface=PELLE_COMUNIONE001338. 339. ** ~~~ ** (Dot Product indicator=184.4593)340. 341. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.342. 343. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)344. 345. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001346. 347. ** ~~~ ** because vertex 1 of back surface=WIN_002_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001348. 349. ** ~~~ ** (Dot Product indicator=180.7210)350. 351. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.352. 353. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)354. 355. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001356. 357. ** ~~~ ** because vertex 3 of back surface=WIN_002_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001358. 359. ** ~~~ ** (Dot Product indicator=180.7210)360. 361. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.362. 363. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)364. 365. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001366. 367. ** ~~~ ** because vertex 2 of back surface=WIN_002_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001368. 369. ** ~~~ ** (Dot Product indicator=180.7210)370. 371. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.372. 373. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)374. 375. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001376. 377. ** ~~~ ** because vertex 1 of back surface=WIN_002_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001378. 379. ** ~~~ ** (Dot Product indicator=180.7210)380. 381. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.382. 383. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)384. 385. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001386. 387. ** ~~~ ** because vertex 3 of back surface=PELLE_SOTTO is in front of receiving surface=PELLE_COMUNIONE001388. 389. ** ~~~ ** (Dot Product indicator=184.4593)390. 391. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.392. 393. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)394. 395. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001396. 397. ** ~~~ ** because vertex 4 of back surface=PELLE_SOTTO is in front of receiving surface=PELLE_COMUNIONE001398. 399. ** ~~~ ** (Dot Product indicator=184.4593)400. 401. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.402. 403. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)404. 405. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001406. 407. ** ~~~ ** because vertex 7 of back surface=PELLE_SOTTO is in front of receiving surface=PELLE_COMUNIONE001408. 409. ** ~~~ ** (Dot Product indicator=184.4593)410. 411. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.412. 413. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)414. 415. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001416. 417. ** ~~~ ** because vertex 8 of back surface=PELLE_SOTTO is in front of receiving surface=PELLE_COMUNIONE001418. 419. ** ~~~ ** (Dot Product indicator=184.4593)420. 421. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.422. 423. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)424. 425. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001426. 427. ** ~~~ ** because vertex 1 of back surface=PELLE_SOPRA_DUP is in front of receiving surface=PELLE_COMUNIONE001428. 429. ** ~~~ ** (Dot Product indicator=184.4593)430. 431. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.432. 433. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)434. 435. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001436. 437. ** ~~~ ** because vertex 4 of back surface=PELLE_SOPRA_DUP is in front of receiving surface=PELLE_COMUNIONE001438. 439. ** ~~~ ** (Dot Product indicator=184.4593)440. 441. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.442. 443. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)444. 445. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001446. 447. ** ~~~ ** because vertex 5 of back surface=PELLE_SOPRA_DUP is in front of receiving surface=PELLE_COMUNIONE001448. 449. ** ~~~ ** (Dot Product indicator=184.4593)450. 451. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.452. 453. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)454. 455. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001456. 457. ** ~~~ ** because vertex 8 of back surface=PELLE_SOPRA_DUP is in front of receiving surface=PELLE_COMUNIONE001458. 459. ** ~~~ ** (Dot Product indicator=184.4593)460. 461. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.462. 463. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)464. 465. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001466. 467. ** ~~~ ** because vertex 1 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE002468. 469. ** ~~~ ** (Dot Product indicator=167.5695)470. 471. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.472. 473. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)474. 475. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001476. 477. ** ~~~ ** because vertex 2 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE002478. 479. ** ~~~ ** (Dot Product indicator=167.5695)480. 481. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.482. 483. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)484. 485. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001486. 487. ** ~~~ ** because vertex 3 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE002488. 489. ** ~~~ ** (Dot Product indicator=195.1092)490. 491. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.492. 493. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)494. 495. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001496. 497. ** ~~~ ** because vertex 4 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE002498. 499. ** ~~~ ** (Dot Product indicator=195.1092)500. 501. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.502. 503. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)504. 505. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001506. 507. ** ~~~ ** because vertex 3 of back surface=PELLE_COMUNIONE001 is in front of receiving surface=PELLE_COMUNIONE002508. 509. ** ~~~ ** (Dot Product indicator=167.5695)510. 511. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.512. 513. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)514. 515. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001516. 517. ** ~~~ ** because vertex 4 of back surface=PELLE_COMUNIONE001 is in front of receiving surface=PELLE_COMUNIONE002518. 519. ** ~~~ ** (Dot Product indicator=167.5695)520. 521. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.522. 523. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)524. 525. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001526. 527. ** ~~~ ** because vertex 1 of back surface=WIN_005 is in front of receiving surface=PELLE_COMUNIONE002528. 529. ** ~~~ ** (Dot Product indicator=32.0568)530. 531. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.532. 533. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)534. 535. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001536. 537. ** ~~~ ** because vertex 2 of back surface=WIN_005 is in front of receiving surface=PELLE_COMUNIONE002538. 539. ** ~~~ ** (Dot Product indicator=139.1556)540. 541. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.542. 543. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)544. 545. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001546. 547. ** ~~~ ** because vertex 3 of back surface=WIN_005 is in front of receiving surface=PELLE_COMUNIONE002548. 549. ** ~~~ ** (Dot Product indicator=139.1556)550. 551. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.552. 553. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)554. 555. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001556. 557. ** ~~~ ** because vertex 4 of back surface=WIN_005 is in front of receiving surface=PELLE_COMUNIONE002558. 559. ** ~~~ ** (Dot Product indicator=32.0568)560. 561. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.562. 563. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)564. 565. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001566. 567. ** ~~~ ** because vertex 1 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE002568. 569. ** ~~~ ** (Dot Product indicator=167.5695)570. 571. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.572. 573. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)574. 575. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001576. 577. ** ~~~ ** because vertex 2 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE002578. 579. ** ~~~ ** (Dot Product indicator=167.5695)580. 581. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.582. 583. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)584. 585. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001586. 587. ** ~~~ ** because vertex 3 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE002588. 589. ** ~~~ ** (Dot Product indicator=167.5695)590. 591. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.592. 593. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)594. 595. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001596. 597. ** ~~~ ** because vertex 4 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE002598. 599. ** ~~~ ** (Dot Product indicator=167.5695)600. 601. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.602. 603. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)604. 605. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001606. 607. ** ~~~ ** because vertex 1 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002608. 609. ** ~~~ ** (Dot Product indicator=195.1092)610. 611. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.612. 613. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)614. 615. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001616. 617. ** ~~~ ** because vertex 2 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002618. 619. ** ~~~ ** (Dot Product indicator=195.1092)620. 621. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.622. 623. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)624. 625. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001626. 627. ** ~~~ ** because vertex 3 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002628. 629. ** ~~~ ** (Dot Product indicator=195.1092)630. 631. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.632. 633. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)634. 635. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001636. 637. ** ~~~ ** because vertex 4 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002638. 639. ** ~~~ ** (Dot Product indicator=195.1092)640. 641. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.642. 643. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)644. 645. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001646. 647. ** ~~~ ** because vertex 5 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002648. 649. ** ~~~ ** (Dot Product indicator=195.1092)650. 651. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.652. 653. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)654. [...]
thisthe errorthat appen when i lunch E+ with only one zone....what is going on???? …