ant to find all paths where exactly two items are the same like in branch {1}. How can I solve this in VB? Is there an easy "search in list" class or do I have to iterate over all items by myself ??
Regards Alex…
a seed, and instead creating a pattern where each color has a seed/control slider for each row? For example, row 1: brown 2, tan 6, yellow 7, purple 3, repeat. row 2: brown 6, tan 1, yellow 4, purple 10, repeat. row 3: yellow 5, purple 1, brown 3, tan 10, repeat. row 4: purple 2, brown 7, tan 3, yellow 4, repeat. Then repeat that sequence up the wall? For each color, the number in the sequence should be adjustable.
Thank you again for your help!…
should not be open).
3. All releases of Rhino 5, Arduino, GH, and FF are the latest as of May 21st.
I Boolean toggled the port open, but I can't seem to get any output to display from the UnoRead component. I was hoping to see values from any of the analog inputs (APin5 depicted) connected as info gets sent back and forth between the Arduino and my comp. I'm getting simultaneous "Hooray" and "Whoops" messages, and I can't pinpoint why. See attached JPG.
Does it have to do with the fact that I have a list of COM ports? Even though I know COM 3 is the correct one as defined in the IDE, do I need to re-declare it in Grasshopper as well? Does the {0} shown impact this output?
Any direction is appreciated.
Thanks - JFig
…
53 → 53 → 63 → 74 → 74 → 84 → 9
As you can see from the above list the connection sequence comes in waves of three, where each group of similar indices on the left is associated with a group of three incrementing indices on the right.
Some combination of Series components will probably generate this list, but it'll only work for the first ring, the second one will need a different connection pattern. It is perhaps better to just encode the integer pairs by hand. But then you cannot change your mind about the number of sides later.…
Added by David Rutten at 10:39am on October 21, 2015
The best way is to use a C# or a VB component to transpose these
lists. I think in C# you can use transpose directly. You can ask this
on the VB/C# forum on our new website, www.grasshopper3d.com
- Scott
On May 27, 3:56 am, Tonsgaard wrote:
> Being a long time user of Generative Components trying to use
> grasshopper i miss the "transpose" command.
> I have a point list like this:
>
> 0, 1, 2, 3, 4, 5
> 0, 1, 2, 3, 4, 5
> 0, 1, 2, 3, 4, 5
> 0, 1, 2, 3, 4, 5
> 0, 1, 2, 3, 4, 5
>
> and a want to transpose dimensions to:
>
> 1, 1, 1, 1, 1
> 2, 2, 2, 2, 2
> 3, 3, 3, 3, 3
> 4, 4, 4, 4, 4
> 5, 5, 5, 5, 5
>
> Surely I am not the first in need of this...
> how would i go about and do this...? I suppose its quite easy in VB
> script, but being used to GC's C# like language, I kinda dont know how
> to do this...
>
> thanks...
>
> Tonsgaard…
en 3 of them, and one poolyline between two of them.
It would also be very nice if i could control it so that only the successive ones can be connected
so if {0:0:0} has 8 points and {0:0:1} has 8, as do {0:0:5} and {0:0:6} i would like to have this as two polylines, not one continoous that would in this case jump three branches (or curves that are shorter).
Does this make any sense?…
Added by Dusan Bosnjak at 2:08pm on September 28, 2009