output will show a tree with 3 branches of 4 integers each that I can pass on to other components. What is the best way to do it?
I have tried creating a tree and using a for loop to do so, but it didn't work.
Thank you for your help.
…
7, 9, 12 and 13 to be able to rotate freely around the y axis at nodes 2, 3, 6, 7, 10 and 11 respectively. The last 2 conditions, for elements 12 and 13, doesn't give any problems, but the first 4 does.
Any help?
…
re-organized code, the preview at "(1)" is static, before the simulation; it is hidden to see the simulation. The preview at "(2)" is the simulation, which traces each tool path and then reveals each one piped.
…
Added by Joseph Oster at 5:56pm on November 1, 2017
can gain that much. If you used nested "if else" statements or "andalso" statements in the previous version most of the iterations should stop after the first distance comparison.…
Added by Vicente Soler at 2:36pm on December 1, 2012
EC
1. Between hours 1:00 to 24:002. Current document units is in Meters3. Conversion to Meters will be applied = 1.0004. [1 of 7] Writing simulation parameters...5. [2 of 6] No context surfaces...6. [3 of 6] Writing geometry...7. [4 of 6] Writing materials and constructions...8. [5 of 7] Writing schedules...9. [6 of 7] Writing loads and ideal air system...10. [7 of 7] Writing outputs...11. ...... idf file is successfully written to : c:\ladybug\Freeformtower_IDF\EnergyPlus\Freeformtower_IDF.idf12. 13. Analysis is running!...14. ......
Done! Read below for errors and warnings:
15. 16. Program Version,EnergyPlus-Windows-64 8.1.0.009, YMD=2015.04.04 23:39,IDD_Version 8.1.0.00917. 18. ************* IDF Context for following error/warning message:19. 20. ************* Note -- lines truncated at 300 characters, if necessary...21. 22. ************* 577 Zone,23. 24. ************* Only last 1 lines before error line shown.....25. 26. ************* 578 Freeformbuilding27. 28. ** Warning ** IP: IDF line~578 Comma being inserted after:" Freeformbuilding" in Object=ZONE29. 30. ** Severe ** Out of range value Numeric Field#5 (Type), value=0.00000, range={>=1 and <=1}, in ZONE=FREEFORMBUILDING31. 32. ************* IDF Context for following error/warning message:33. 34. ************* Note -- lines truncated at 300 characters, if necessary...35. 36. ************* 586 BuildingSurface:Detailed,7341.
…
in the desired order.
0 = 0
1 = 1
2 = 6
3 = 7
4 = 8
5 = 9
6 = 12
7 = 13
8 = 2
9 = 3
10 = 4
11 = 5
12 = 10
13 = 11
Where the first number is the index and the second number is the actual sorting key. Then you sort these keys while sorting your curves in parallel using the A input of the Sort component.
--
David Rutten
david@mcneel.com
Poprad, Slovakia…
ggle A
7. Toggle A
8. Toggle 2
9. Toggle 3
10. Toggle A
11. Toggle A
12. Toggle 3
I was thinking to use somehow slider and animate option....but without luck
Any idea would be appreciated…
onsecutive points at the same height then your 'Break at discontinuities' component eliminates the middle point completely and then the 'Interpolate Curve' component gives a much bigger bump in the wrong direction. This was enough to get curves to meet from opposite sides.
I fixed this by changing the heights to 1.1 or 2.9, rather than 1.0 and 3.0, but it took a little while to work it out! Sigh.
I attach a new version. But I actually preferred it as it was before. See what you think!
Bob
p.s. in the first list, elements 11, 12, 23 and 24 go from 1 to 3; elements 17 and 18 go from 3 to 1. In the second list, elements 6, 17, 18 and 29 go from 1 to 3; elements 12 and 23 go from 3 to 1. Given the above fix, these can be easily seen.…
Added by Bob Mackay at 10:40pm on November 24, 2015