NONE, in SIZING:PARAMETERS". I'm not sure of where to start in troubleshooting this. I've attached the file.
Thank you,
See the errors and warnings below:
{0;0;0}
0. Current document units is in Meters
1. Conversion to Meters will be applied = 1.000
2. [1 of 8] Writing simulation parameters...
3. [2 of 8] Writing context surfaces...
4. [2 of 8] Writing context surfaces...
5. [3 of 8] Writing geometry...
6. [4 of 8] Writing Electric Load Center - Generator specifications ...
7. [5 of 8] Writing materials and constructions...
8. [6 of 8] Writing schedules...
9. [7 of 8] Writing loads and ideal air system...
10. [8 of 8] Writing outputs...
11. ...
... idf file is successfully written to : R:\Green\SuRG\Building_Performance_Analysis\2016_analysis_studies\Energy_Analysis_Comparison\Honeybee_+_Ladybug\tutorial01\EnergyPlus\tutorial01.idf
12.
13. Analysis is running!...
14. ...
...
Done! Read below for errors and warnings:
15.
16. Program Version,EnergyPlus, Version 8.5.0-c87e61b44b, YMD=2016.10.31 11:39,IDD_Version 8.5.0
17.
18. ************* IDF Context for following error/warning message:
19.
20. ************* Note -- lines truncated at 300 characters, if necessary...
21.
22. ************* 24 Sizing:Parameters,
23.
24. ************* Only last 1 lines before error line shown.....
25.
26. ************* 25 None, !- Heating Sizing Factor
27.
28. ** Severe ** IP: IDF line~25 Invalid Number in Numeric Field#1 (Heating Sizing Factor), value=NONE, in SIZING:PARAMETERS
29.
30. ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
31.
32. ** ~~~ ** Possible Invalid Numerics or other problems
33.
34. ** Fatal ** IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination.
35.
36. ...Summary of Errors that led to program termination:
37.
38. ..... Reference severe error count=1
39.
40. ..... Last severe error=IP: IDF line~
, value=NONE, in SIZING:PARAMETERS
41.
42. ************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).
43.
44. ************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.
45.
46. ************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
47.
48. ************* EnergyPlus Sizing Error Summary. During Sizing: 0 Warning; 0 Severe Errors.
49.
50. ************* EnergyPlus Terminated--Fatal Error Detected. 1 Warning; 1 Severe Errors; Elapsed Time=00hr 00min 9.34sec
51.…
0, 5, 10, 15, 20
1, 6, 11, 16, 21
2, 7, 12, 17, 22
3, 8, 13, 18, 23
4, 9, 14, 19, 24
and if i'm here is because i'm not able... :)
can you help me?
thank you
…
} (N=11) {0;1} (N=11) {0;2}(N = 11) {0;3}(N = 11) {0;4}(N = 11)
2. I run the Points that are coming out from the Divide Curve Components through the Path Mapper components with this definition:
{A;B} (i) > {A} (i)
3. I run data coming out from Path Mapper component through:
a) Parameter Viewer component and the result is:
{0} N=11 (data with 1 branches)
b) Point > Panel and the result is:
collection of 11 point (N=11) which is the exactly the same as the collection of point belonging to {0;4} (N = 11).
So, here is the question:
why the collection of points coming out from the Path Mapper {A;B} (i) > {A} (i) component is the same as the collection of points belonging to the curve {0;4}(N = 11) ?
Anyway ... It 's the first time I ask a question here... so I would like to thank you for what you do with your work! Thank you! You are really great!…
s than 40% on average.2. 8gb usage is steady at 28% 3. I've been now looking at 2 blank white screen, in both Rhino and Grasshopper for well over 20 min. finally I went for a walk at 10:25am, (its a beautiful day why waste it looking at nonexistent calculations, It would help if there was a timing function in the code that would let me know how long the calculations were going to take, came back 11:25am still no results. Had to Quit Rhino in the Start manager.
I have used all sorts of window programs for well over 25 years. Rhino and Grasshopper are the only 2 programs that I have ever seen that show totally white screens in their operating windows :(
…
ve a Vertex [V] connected to four other Vertexs [N1-N4].
Each of the has a Value:
V ... 1
N1 ... 5
N2 ... 3
N3 ... 8
N4 ... 11
The Average Filter would set the Value of [V] to
(1+5+3+8+11)/5 = 5,6
The Median Filter would Sort Values and pick the middle one
1,3, [5], 8, 11
Hope that helped...…
are on their own paths, but the first branch contains 3 curves and the second one 2 curves. If you want the same result for all pairs of curves you'd need to split up the first and second branches, so that all curves are on their own branch.…
Added by Lars Renklint at 4:33am on September 6, 2009
e range of materials, including heavy-duty fabrics. They offer a range of embroidery machines that cater to different needs and budgets.best embroidery machine for custom designs…