1 JUN to 31 DECBetween hours 1:00 to 24:00Current document units is in MetersConversion to Meters will be applied = 1.000[1 of 7] Writing simulation parameters...Ground temperature data contains monthly average temperatures at 3 different depths .5 meters (1st)2 meters (2nd)4meters (3rd)respectively[2 of 6] No context surfaces...[3 of 6] Writing geometry...[4 of 6] Writing materials and constructions...[5 of 7] Writing schedules...[6 of 7] Writing loads and ideal air system...[7 of 7] Writing outputs......... idf file is successfully written to : c:\ladybug\unnamed\EnergyPlus\unnamed.idf
Analysis is running!...c:\ladybug\unnamed\EnergyPlus\eplusout.csv......
Done! Read below for errors and warnings:
Program Version,EnergyPlus, Version 8.3.0-6d97d074ea, YMD=2015.05.24 11:32,IDD_Version 8.3.0
** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
** Warning ** Version: in IDF="'8.1.0'" not the same as expected="8.3"
************* Beginning Zone Sizing Calculations
** Severe ** GetSurfaceData: Some Outward Facing angles of subsurfaces differ significantly from base surface.
** ~~~ ** ...use Output:Diagnostics,DisplayExtraWarnings; to show more details on individual surfaces.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=AW0 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=AW0 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=AW0 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=AW0 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=AW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=AW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=AW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=AW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=AW2 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=AW2 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=AW2 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=AW2 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=AW3 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=AW3 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=EW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=EW1 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=0.9038)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=0.9038)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=16.0967)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=GLZ_0_EW1_1F6383543B434F648813 is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=16.0967)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 6 of back surface=FLOOR is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 7 of back surface=FLOOR is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 8 of back surface=FLOOR is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 9 of back surface=FLOOR is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 5 of back surface=CIELING is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 6 of back surface=CIELING is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=17.1101)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 7 of back surface=CIELING is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 8 of back surface=CIELING is in front of receiving surface=EW0
** ~~~ ** (Dot Product indicator=30.0900)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=AW6 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=AW6 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=WALLW1 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=WALLW1 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=WALLW1 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=WALLW1 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=GLZ_0_WALLW1_103854D39BEF453D8A4E is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=EW0 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=EW0 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=1.4709)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=1.4709)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=15.6696)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 4 of back surface=GLZ_0_EW0_6AEDE94222384E5B8950 is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=15.6696)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 1 of back surface=FLOOR is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=FLOOR is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 2 of back surface=CIELING is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Severe ** Problem in interior solar distribution calculation (CHKBKS)
** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone="APRATMENT1"
** ~~~ ** because vertex 3 of back surface=CIELING is in front of receiving surface=EW1
** ~~~ ** (Dot Product indicator=17.0963)
** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.
** Warning ** ManageSizing: For a plant sizing run, there must be at least 1 Sizing:Plant object input. SimulationControl Plant Sizing option ignored.
************* Testing Individual Branch Integrity
************* All Branches passed integrity testing
************* Testing Individual Supply Air Path Integrity
************* All Supply Air Paths passed integrity testing
************* Testing Individual Return Air Path Integrity
************* All Return Air Paths passed integrity testing
************* No node connection errors were found.
************* Beginning Simulation
************* Simulation Error Summary *************
** Warning ** The following Report Variables were requested but not generated
** ~~~ ** because IDF did not contain these elements or misspelled variable name -- check .rdd file
************* Key=*, VarName=ZONE PACKAGED TERMINAL HEAT PUMP TOTAL COOLING ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE PACKAGED TERMINAL HEAT PUMP TOTAL HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=CHILLER ELECTRIC ENERGY, Frequency=Hourly
************* Key=*, VarName=BOILER HEATING ENERGY, Frequency=Hourly
************* Key=*, VarName=FAN ELECTRIC ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE VENTILATION FAN ELECTRIC ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE VENTILATION TOTAL HEAT LOSS ENERGY, Frequency=Hourly
************* Key=*, VarName=ZONE VENTILATION TOTAL HEAT GAIN ENERGY, Frequency=Hourly
************* There are 1 unused schedules in input.
************* There are 1 unused week schedules in input.
************* There are 3 unused day schedules in input.
************* Use Output:Diagnostics,DisplayUnusedSchedules; to see them.
************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
************* EnergyPlus Sizing Error Summary. During Sizing: 1 Warning; 49 Severe Errors.
************* EnergyPlus Completed Successfully-- 4 Warning; 49 Severe Errors; Elapsed Time=00hr 00min 4.59sec
Thanks Abraham.I really appreciate it.
Another thing ' I posted a discussion few days ago and got no replies.And this forum is the only 'Hope' for me..Can you quickly check it?thanks.
N
http://www.grasshopper3d.com/group/ladybug/forum/topics/free-form-external-wall-with-glazing-workflow?xg_source=activity
…
tions or components.
Participants will learn concepts of object oriented programming and essential syntax of C# to endeavour into personally extending cad toolsets. The workshop will focus on introducing the .NET language C# and the Software Development Kit (SDK) RhinoCommon.
Topics
- use of Script Component within Grasshopper
- explanation to the .NET Framework
- introduction to RhinoCommon SDK
- basics of imperative / object-oriented programming
- data types, operators, properties
- variables, arrays, lists, enumerations
- methods
- objects, classes
- control structures: conditional statements (if, else, switch)
- control structures: loops (for, foreach, while, do)
- walk-through iterative und recursive code-samples
- use of RhinoCommon Geometry class library: creation, sorting, editing of Geometry (Points, Vectors, Curves, Surfaces)
- adding (baking) geometry to the active Rhino 3DM Document, including attributes (Name, Layer, Colors etc.)
- introduction to the Integrated Development Environment MS Visual Studio Express Edition
- compiling code to dll/gha files (plug-ins) / making your own Grasshopper custom components
Grasshopper wird auf der .NET Softwareplattform entwickelt, und kann ebenso wie das CAD Programm Rhinoceros mit "RhinoCommon", einem Software Development Kit, erweitert werden.
Dieser Kurs richtet sich an Designer, Architekten, Ingenieure und Techniker, welche mit dem grafischen Algorithmus-Modellierer "Grasshopper3d" sowie dem CAD-Programm "Rhinoceros" bereits vertraut sind und einen Einstieg in die Programmierung von Geometrie erlernen möchten.
Der Kurs Grasshopper II folgende Grundlagen:
Kennenlernen der Script Componente
Erläuterung zum .NET Framework
Einführung in RhinoCommon SDK
Grundlagen d. imperativen / objektorientierten Programmierung
Datentypen, Operatoren, Eigenschaften
Variablen, Reihen, Listen, Aufzählungen
Methoden
Objekte und Klassen
Kontrollstrukturen: Bedingte Ausführung, Schleifen
praxisnahe iterative und rekursive Code-Beispiele für generatives Design unter Verwendung der RhinoCommon Geometrie Klassenbibiliothek - Punkt- und Vektorgeometrie erstellen, sortieren, bearbeiten, Flächen und Netze erstellen - Geometrie in das Rhino 3DM Dokument baken, einschließlich Attribute (Name, Layer, Color)
Einführung in die Entwicklungsumgebung MS Visual Studio Express Edition
Kompilieren von Programmerweiterungen (plug-ins) als Komponenten (custom components)
Details, Anmeldung:
www.vhs-stuttgart.de
Trainer Peter Mehrtens
Kursdauer: 3 Tage x 8 h
Freitag, 21.02.2014, 9:00-17:00 Uhr Samstag, 22.02.2014, 9:00-17:00 Uhr Sonntag, 23.02.2014, 9:00-17:00 Uhr Ort: VHS Stuttgart, Fritz-Elsas-Str. 46/48
Teilnahmegebühr 510,00 €…
the loops haven't even started yet. This is a one time overhead - re-starting the loops after that doesn't have this long delay until you close and re-open the file.
Second, I got some encouraging results rather quickly but then spent WAY TOO MUCH TIME trying to replace the inner loop with a "Fast Loop". These are not well behaved in the sense that they don't respond to <ESC> like the "Classic" loops do so you can't stop them; and I never got the same results as the "Classic", no matter what I tried - but ultimately, I just got too frustrated with "Fast Loop" causing Rhino/GH and my whole laptop to freeze up - VERY BAD!!!!!!!!!!
I re-wired the loops slightly so that the hour used by your 'analysisPeriod' cluster is determined by the 'D0' value inside the inner loop.
I added a "Loop On / Loop Off" switch to stop/start the looping (which was useless with "Fast Loop" - grrr....).
I 'Simplified' the 'D1' output of the inner loop and enabled 'Record data' and 'Output after the last' on the outer loop.
And I got this - four buildings over three hours takes about 20 seconds:
Eleven buildings over three hours takes about one minute.
I'm not sure what will happen when I increase the hours and number of buildings but will try it when I have more time. It might be a good idea to avoid writing to Excel inside the loops and wait for the end results before writing them to an Excel file?
There are more possibilities for re-wiring based on simplifying various outputs but I'm tired of this for now and have other things to do. The exponential slowdown you observed might be due in part to Anemone adding an extra branch path every time it loops; adding 'Simplify' might help this?
P.S. 11 buildings over 13 hours (6am to 6pm) took 5 minutes 38 seconds.…
Added by Joseph Oster at 12:54pm on January 18, 2016
the use of digital technologies as architectural design tools. The workshop " Computer Aided Design: parametric design and digital fabrication " aims to do some introductory teaching in the use of some of these tools.
The workshop will focus on the use of computational models of parametric behavior for generating architectural forms. The generative capacity of these models it will be tested in the development of designs defined by repetitive non-standard components, based on the parametric control of its variations and series differentiations. This process will be developed by the use of a three-dimensional modeling software - Rhinoceros, associated with an application for visual programming - Grasshopper.
The last day of the workshop is dedicated to the use of digital manufacturing tools in architecture. Part of the work will take place at the facilities of the Institute of Design of Guimarães (IDEGUI) providing for the use of their laboratories and manufacturing CNC machines (computer numerically controlled).
At the end of the workshop, it is intended the students to understand that the use of digital technologies in architecture can overcome representational functions, and their integration in the design conception, analysis and construction enriches the methodology of project development.
Terms & Participants
The workshop will take place at the School of Architecture of the University of Minho (Campus Azurém, Guimarães) and the Institute of Design of Guimarães (Couros, Guimarães).
The workshop is pointed at students who attend the 3rd year and 4th year from MiArq, EAUM.
The maximum acceptance is 20 students and a minimum of 10 students.
Deadline for entries is April 11 and must be performed by eaum.pac@gmail.com.
Program summary :
Day 23 April 14 -20h
Introduction to 3D modeling in Rhinoceros. Regular geometries, ruled surfaces and NURBS surfaces.
Day 30 April 14 -20h
Parametric design in architecture. Introduction to methods of visual programming.
May 1, 9 -13h 14 -18h
Development of a design idea by the use visual programming processes in Grasshopper.
May 2, 9 -13h 14 -18h
Introduction to methods of digital fabrication. Manufacture physical models of the proposals made.
It is expected that this meeting will take place in the IDEGUI labs.
team:
Bruno Figueiredo ( Lecturer, EAUM )
Paulo Sousa ( PhD candidate , EAUM )
Nuno Cruz ( Invited Lecturer , EAUM )
Cláudia Alvares ( 5th year MiArq student , EAUM )
Javier Bono ( 4th year MiArq student, EAUM )
João Amaro ( 5th year MiArq student, EAUM )…
r [String Split] in version 0.9.0014)
The [Timer] prompts a component to up date at the set interval. in this case every 1 seconds.
The [Time] param is a placeholder for a time in the same way that a [Number] param can hold real numbers.
By using "Now" as the input to the [Time] param you will get the current time when the param updates. therefore every second it resets to the current time.
The [Text Split] is there to separate the output of [Time] in a string format at every colon ":"
Therefore "Monday, 13-MAY-2013 (11:23:30)" would become:
0 Monday, 13-MAY-2013 (1
1 23
2 30)
The next two components use this to convert it into the current seconds. Because we are after the last item "30)" we can use [List Item] on a reversed list to get the last item.
Now we have to remove the ")" with [Replace String] but we are replacing it with nothing so it disappears.
The Arrow is part of the Sketch Tool Functionality of the canvas.
Lastly the 3 different inputs should go into the three different Inputs of the [Stream Filter]
…
is set up to manipulate strings into an STL file that is quite different from how Grasshopper defines meshes, in that an STL seems to define each face by XYZ points, Grasshopper wants a single list of all vertex points and then has an allied lists of topological connectivity according to vertex number, so for now I just hacked it to spit out points minus so many duplicates it generates for STL:
Right now it has an internal 3D trigonometric function I added input sliders to control, that creates surfaces that look a lot like molecular orbitals.
So how do I make a mesh? I failed to make a single mesh face from each STL face since AddMesh seems to want a list, so I tried making a single list and matching it with a simple ((1,2,3),(4,5,6),(7,8,9)...) array of connectivity but it hasn't worked yet since the STL list of vertices has duplicates that won't work for Grasshopper and removing the duplicates scrambles the connectivity relation.
After some work on this and seeing the output, I figure I could just randomly populate the mathematical function with points instead, unless it really gives a better mesh result than other routines. I'm not sure what to do with it yet, even if I get the mesh figured out.
import rhinoscriptsyntaximport RhinoPOINTS_CONTAINER =[]POINTS = []class Vector: # struct XYZ def __init__(self,x,y,z): self.x=x self.y=y self.z=z def __str__(self): return str(self.x)+" "+str(self.y)+" "+str(self.z) class Gridcell: # struct GRIDCELL def __init__(self,p,n,val): self.p = p # p=[8] self.n = n # n=[8] self.val = val # val=[8] class Triangle: # struct TRIANGLE def __init__(self,p1,p2,p3): self.p = [p1, p2, p3] # vertices # HACK TO GRAB VERTICES FOR PYTHON OUTPUT POINTS_CONTAINER.append( (p1.x,p1.y,p1.z) ) POINTS_CONTAINER.append( (p2.x,p2.y,p2.z) ) POINTS_CONTAINER.append( (p3.x,p3.y,p3.z) )# return a 3d list of values def readdata(f=lambda x,y,z:x*x+y*y+z*z,size=5.0,steps=11): m=int(steps/2) ki = [] for i in range(steps): kj = [] for j in range(steps): kd=[] for k in range(steps): kd.append(f(size*(i-m)/m,size*(j-m)/m,size*(k-m)/m)) kj.append(kd) ki.append(kj) return ki from math import sin,cos,exp,atan2 def lobes(x,y,z): try: theta = atan2(x,y) # sin t = o except: theta = 0 try: phi = atan2(z,y) except: phi = 0 r = x*x+y*y+z*z ct=cos(PARAMETER_A * theta) cp=cos(PARAMETER_B * phi) return ct*ct*cp*cp*exp(-r/10) def main(): data = readdata(lobes,10,40) isolevel = 0.1 #print(data) triangles=[] for i in range(len(data)-1): for j in range(len(data[i])-1): for k in range(len(data[i][j])-1): p=[None]*8 val=[None]*8 #print(i,j,k) p[0]=Vector(i,j,k) val[0] = data[i][j][k] p[1]=Vector(i+1,j,k) val[1] = data[i+1][j][k] p[2]=Vector(i+1,j+1,k) val[2] = data[i+1][j+1][k] p[3]=Vector(i,j+1,k) val[3] = data[i][j+1][k] p[4]=Vector(i,j,k+1) val[4] = data[i][j][k+1] p[5]=Vector(i+1,j,k+1) val[5] = data[i+1][j][k+1] p[6]=Vector(i+1,j+1,k+1) val[6] = data[i+1][j+1][k+1] p[7]=Vector(i,j+1,k+1) val[7] = data[i][j+1][k+1] grid=Gridcell(p,[],val) triangles.extend(PolygoniseTri(grid,isolevel,0,2,3,7)) triangles.extend(PolygoniseTri(grid,isolevel,0,2,6,7)) triangles.extend(PolygoniseTri(grid,isolevel,0,4,6,7)) triangles.extend(PolygoniseTri(grid,isolevel,0,6,1,2)) triangles.extend(PolygoniseTri(grid,isolevel,0,6,1,4)) triangles.extend(PolygoniseTri(grid,isolevel,5,6,1,4)) def t000F(g, iso, v0, v1, v2, v3): return [] def t0E01(g, iso, v0, v1, v2, v3): return [Triangle( VertexInterp(iso,g.p[v0],g.p[v1],g.val[v0],g.val[v1]), VertexInterp(iso,g.p[v0],g.p[v2],g.val[v0],g.val[v2]), VertexInterp(iso,g.p[v0],g.p[v3],g.val[v0],g.val[v3])) ] def t0D02(g, iso, v0, v1, v2, v3): return [Triangle( VertexInterp(iso,g.p[v1],g.p[v0],g.val[v1],g.val[v0]), VertexInterp(iso,g.p[v1],g.p[v3],g.val[v1],g.val[v3]), VertexInterp(iso,g.p[v1],g.p[v2],g.val[v1],g.val[v2])) ] def t0C03(g, iso, v0, v1, v2, v3): tri=Triangle( VertexInterp(iso,g.p[v0],g.p[v3],g.val[v0],g.val[v3]), VertexInterp(iso,g.p[v0],g.p[v2],g.val[v0],g.val[v2]), VertexInterp(iso,g.p[v1],g.p[v3],g.val[v1],g.val[v3])) return [tri,Triangle( tri.p[2], VertexInterp(iso,g.p[v1],g.p[v2],g.val[v1],g.val[v2]), tri.p[1]) ] def t0B04(g, iso, v0, v1, v2, v3): return [Triangle( VertexInterp(iso,g.p[v2],g.p[v0],g.val[v2],g.val[v0]), VertexInterp(iso,g.p[v2],g.p[v1],g.val[v2],g.val[v1]), VertexInterp(iso,g.p[v2],g.p[v3],g.val[v2],g.val[v3])) ] def t0A05(g, iso, v0, v1, v2, v3): tri = Triangle( VertexInterp(iso,g.p[v0],g.p[v1],g.val[v0],g.val[v1]), VertexInterp(iso,g.p[v2],g.p[v3],g.val[v2],g.val[v3]), VertexInterp(iso,g.p[v0],g.p[v3],g.val[v0],g.val[v3])) return [tri,Triangle( tri.p[0], VertexInterp(iso,g.p[v1],g.p[v2],g.val[v1],g.val[v2]), tri.p[1]) ] def t0906(g, iso, v0, v1, v2, v3): tri=Triangle( VertexInterp(iso,g.p[v0],g.p[v1],g.val[v0],g.val[v1]), VertexInterp(iso,g.p[v1],g.p[v3],g.val[v1],g.val[v3]), VertexInterp(iso,g.p[v2],g.p[v3],g.val[v2],g.val[v3])) return [tri, Triangle( tri.p[0], VertexInterp(iso,g.p[v0],g.p[v2],g.val[v0],g.val[v2]), tri.p[2]) ] def t0708(g, iso, v0, v1, v2, v3): return [Triangle( VertexInterp(iso,g.p[v3],g.p[v0],g.val[v3],g.val[v0]), VertexInterp(iso,g.p[v3],g.p[v2],g.val[v3],g.val[v2]), VertexInterp(iso,g.p[v3],g.p[v1],g.val[v3],g.val[v1])) ] trianglefs = {7:t0708,8:t0708,9:t0906,6:t0906,10:t0A05,5:t0A05,11:t0B04,4:t0B04,12:t0C03,3:t0C03,13:t0D02,2:t0D02,14:t0E01,1:t0E01,0:t000F,15:t000F} def PolygoniseTri(g, iso, v0, v1, v2, v3): triangles = [] # Determine which of the 16 cases we have given which vertices # are above or below the isosurface triindex = 0; if g.val[v0] < iso: triindex |= 1 if g.val[v1] < iso: triindex |= 2 if g.val[v2] < iso: triindex |= 4 if g.val[v3] < iso: triindex |= 8 return trianglefs[triindex](g, iso, v0, v1, v2, v3) def VertexInterp(isolevel,p1,p2,valp1,valp2): if abs(isolevel-valp1) < 0.00001 : return(p1); if abs(isolevel-valp2) < 0.00001 : return(p2); if abs(valp1-valp2) < 0.00001 : return(p1); mu = (isolevel - valp1) / (valp2 - valp1) return Vector(p1.x + mu * (p2.x - p1.x), p1.y + mu * (p2.y - p1.y), p1.z + mu * (p2.z - p1.z)) if __name__ == "__main__": main() # GRASSHOPPER PYTHON OUTPUTPOINTS = rhinoscriptsyntax.AddPoints(POINTS_CONTAINER)POINTS = rhinoscriptsyntax.CullDuplicatePoints(POINTS)…
rested in specializing in the field of Computational design.
The workshop will help understand how Grasshopper facilitates during the design process allowing one to Generate, Automate and Manipulate data.
To Register:
Mail us at intofablab@gmail.com
Workshop Structure:
Day 01: 11 February 2019
Introduction to Computational Processes in Architecture
Understanding Grasshopper and its relation to Rhino3D
Working with fields and Grids (Supplementary readings for Architectural theory)
Spatial Concepts using Data
Day 02: 12 February 2019
Understanding Data in Grasshopper - LISTS
Managing Data in Grasshopper (Supplementary reading)
Experimentation on Massing and Architectural Forms
Day 03: 13 February 2019
Understanding Data in Grasshopper – Trees
Surface Logics (Supplementary reading)
Design Exercise and Prototyping
Day 04: 14 February 2019
Architectural Skins
Day 05: 15 February 2019
MasterClass Project
Introduction to various types of Digital Fabrications
Prototyping of works during the Workshops
Basic knowledge of Rhino 5 is required to be able to take this training.
CERTIFICATION: All participants will receive a Workshop certificate from Authorized Rhino Trainer.
3D Printing: Prototyping of works during the Workshops
Workshop Tutor:
Kavitha M, an Architect and Computational Designer, 3D Printing Specialist is also the co-founder of INTO Design Research, will head the Computational Process in Architecture using Grasshopper workshop. Graduated from Stadelschule Architecture class with Masters in Advanced Architecture Design, has been researching on teaching methodologies on digital tools and their influence on Design thinking.…
sinergetici associati alla compresenza simultanea di differenti strumenti di analisi e digital design all'interno di un processo di progettazione in svolgimento. I partecipanti utilizzeranno Grasshopper (modellatore parametrico per Rhino): l'uso di questo editor grafico di algoritmi si integra alla perfezione con gli strumenti di modellazione di Rhinoceros 3D espandendo le possibilità di corstruire modelli parametrici altamente complessi. Per generare una complessità simile saranno utilizzati collegamenti live ai diversi programmi elencati di seguito: . Autodesk Ecotect Analysis via GECO . FEA software GSA via SSI Durante questi intensi 3 giorni, i partecipanti impareranno il workflow dei plug-ins con l'aiuto di esempi esplorando una panoramica dei differenti software, le possibilità di testare le performances di un progetto o l'uso di strumenti addizionali non legati ad un singolo sistema (es. accentuazione, formazione, reazione parametrica) [english text] The focus of the workshop is to integrate and correlate the synergistic effect associated with simultaneous presence of different digital design- and analysis tools in an ongoing design process. The main attention is set on easy to handle interface , which should be used at a early stage of conceptual design to respond to external and internal influences in a intelligent and sustainable way. Participants will use the software Grasshopper as a parametric modeling plug-in for Rhino. The usage of this graphical algorithm editor tightly integrated with Rhino's 3-D modeling tools open up the possibility to construct highly parametrical complex models. To generate this complexity we will use live linkages to several programs listed below: . Autodesk Ecotect Analysis via GECO . FEA software GSA via SSI In this 3 intense days, the participants should learn the workflow of the plug-ins with the help of examples and get an overview of the different software's, there possibilities for evaluating the performance of a design or the usage of additional tools to be not chained to a single system . (e.g. parametrical accentuation, parametrical formation, parametrical reaction) [.] Dettagli : Istruttori: Thomas Grabner & Ursula Frick from [uto]. lingua del corso: inglese (saranno disponibili tutor di supporto ma è richiesta una conoscenza di base della lingua unglese).
Quote d'iscrizione (min 12 max 20 posti): educational* : € 280.00 + iva professional: € 450.00 + iva * studenti, docenti, ricercatori, dottorandi e laureati fino a un anno dalla data di laurea OFFERTA EARLY BIRD SPECIAL: le prime 5 domande di iscrizione pervenute entro il 31 Dicembre 2011 avranno diritto ad una quota di iscrizione scontata del 20% Quote d'iscrizione E.B. SPECIAL: E.B. SPECIAL educational* : € 224.00+ iva E.B. SPECIAL professional: € 360.00+ iva. ulteriori info, dettagli e iscrizioni: http://www.co-de-it.com/wordpress/nexus-advanced-grasshopper-workshop-with-uto.html…