s.
Where as 10 by 10 Domain Divide = 100 values
To rectify simply increase Domain Divide inputs by 1 to get 11 x 11 = 121
Thirdly
The Data Matching in the Dispatch Component is for 121 values on 1 branch to 121 values on 11 Branches.
I've flattened the pattern and now have 121 values on 1 branch for each input, which produces a result of open and closed panels in the same shape as your image.…
9 8 7 6
5 4 3 2 1 0
I am triangulating this surface. I want to select just the red vertices. As you can note, I just need the inner vertices of this surface. I could do it mannually, but if I want to change the mesh density later, I will have to pick all of them manually again later.
Can someone help me?
Tks
…
otate 9°, the second module 18°, the third 27°, etc. I can only seem to get all 11 modules to rotate the same... I know it probably has something to do with series but I can't figure it out. the screen shot shows the 11 modules rotating to the same degree and the drawing is a plan of what I am trying to accomplish. Thank you so much in advance!…
Added by Daniel Lamm at 6:54pm on September 4, 2014
NONE, in SIZING:PARAMETERS". I'm not sure of where to start in troubleshooting this. I've attached the file.
Thank you,
See the errors and warnings below:
{0;0;0}
0. Current document units is in Meters
1. Conversion to Meters will be applied = 1.000
2. [1 of 8] Writing simulation parameters...
3. [2 of 8] Writing context surfaces...
4. [2 of 8] Writing context surfaces...
5. [3 of 8] Writing geometry...
6. [4 of 8] Writing Electric Load Center - Generator specifications ...
7. [5 of 8] Writing materials and constructions...
8. [6 of 8] Writing schedules...
9. [7 of 8] Writing loads and ideal air system...
10. [8 of 8] Writing outputs...
11. ...
... idf file is successfully written to : R:\Green\SuRG\Building_Performance_Analysis\2016_analysis_studies\Energy_Analysis_Comparison\Honeybee_+_Ladybug\tutorial01\EnergyPlus\tutorial01.idf
12.
13. Analysis is running!...
14. ...
...
Done! Read below for errors and warnings:
15.
16. Program Version,EnergyPlus, Version 8.5.0-c87e61b44b, YMD=2016.10.31 11:39,IDD_Version 8.5.0
17.
18. ************* IDF Context for following error/warning message:
19.
20. ************* Note -- lines truncated at 300 characters, if necessary...
21.
22. ************* 24 Sizing:Parameters,
23.
24. ************* Only last 1 lines before error line shown.....
25.
26. ************* 25 None, !- Heating Sizing Factor
27.
28. ** Severe ** IP: IDF line~25 Invalid Number in Numeric Field#1 (Heating Sizing Factor), value=NONE, in SIZING:PARAMETERS
29.
30. ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
31.
32. ** ~~~ ** Possible Invalid Numerics or other problems
33.
34. ** Fatal ** IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination.
35.
36. ...Summary of Errors that led to program termination:
37.
38. ..... Reference severe error count=1
39.
40. ..... Last severe error=IP: IDF line~
, value=NONE, in SIZING:PARAMETERS
41.
42. ************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).
43.
44. ************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.
45.
46. ************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
47.
48. ************* EnergyPlus Sizing Error Summary. During Sizing: 0 Warning; 0 Severe Errors.
49.
50. ************* EnergyPlus Terminated--Fatal Error Detected. 1 Warning; 1 Severe Errors; Elapsed Time=00hr 00min 9.34sec
51.…
output will show a tree with 3 branches of 4 integers each that I can pass on to other components. What is the best way to do it?
I have tried creating a tree and using a for loop to do so, but it didn't work.
Thank you for your help.
…
doing this I hope to be able to duplicate the pattern that I have already generated (with items 1 to 11) within every box in the octTree.
Any pointers would be greatly appreciated.
Kind Regards
Joel…
Added by Joel Falconer at 8:15am on September 15, 2015
This must be a bug because its true for dividing by all odd numbers:
(i-1)/3
(i-2)/5
(i-3)/7
(i-4)/9
(i-5)/11
....
(i-n)/2n+1
And you can't make it work for even numbers
Added by Danny Boyes at 5:06pm on January 13, 2010