onents (radiation, sunlight-hours and view analysis) which let you study the effect of the orientation of your building and the analysis result. When you come to a question similar to "what is the orientation that the building receives the most/least amount of radiation?" is probably the right time to use this component.
HOW?
I'll try to explain the steps using a simple example. Here is my design geometries. The building in the center is the building to be designed and the rest of the buildings are context. I want to see the effect of orientation on the amount of the radiation on the test building surfaces from the start of Oct. to the end of Feb. for Chicago.
First I need to set up the normal radiation analysis and run it for the building as it is right now. [I'm not going to explain how you can set up this since you can find it in the sample file (Download the sample file from here)]
Now I need to set up the parameters for orientation study using orientationStudyPar component. You can find it under the Extra tab:
At minimum I need to input the divisionAngle, and the totalAngle and set runTheStudy to True. In this case I put 45 for divisionAngle and 180 for the totalAngle which means I want the study to be run for angles 0, 45, 90, 135 and 180.
[Note1: The divisionAngle should be divisible by totalAngle.]
[Note 2: If you don't provide any point for the basePoint, the component will use the center of the geometry as the center of the rotation.]
[Note 3: You can also rotate the context with the geometry! Normally you don't have the chance to change the context to make your design work but if you got lucky the rotateContext input is for you! Set it to True. The default is set to False.]
You're all set for the orientation study, just connect the orientationStudyPar output to OrientationStudyP input in the component and wait for the result!
The component will run the study for all the orientations and preview the latest geometry. To see the result just grab a quick graph and connect it to totalRadiation. As you can see in the graph 135 is the orientation that I receive the maximum radiation. Dang!
If you want to see all the result geometries set bakeIt to True, and the result will be baked under LadyBug> RadaitionStudy>[projectname]> . The layer name starts with a number which is the totalRadiation.
Mostapha…
her people) a tremendous amount of time creating them by hand. Dog Treat was far from perfect, however it was good enough to use almost daily.
Three years is a long time. Since 2016 my Gh knowledge has expanded and I’ve seen how dodgy some of the scripting is. With this in mind I started work on a new build. Many things have been tweaked and some things have been rebuilt from the ground up.
Everything has been designed to be leaner and be a general solution to the problem of creating dog bone corners on geometry for quick, efficient and safe CNC fabrication.
Some of these things are:
Adding prompts about user geometry to make them aware about open curves, varying curve heights and if their geometry had been altered (mostly removing unnecessary points on curves).
Smooth Transfers. If you’re in a rush and need to speed through cutting, smooth transfers mean that a lead in geometry is now created alongside the actual dog bone arc. This means the router bit doesn’t have to come to a minute stop at every corner. This is turned on by default.
Acute Angle Condition If the angle between the two curves adjacent to a dog bone point is acute, previously the dog bone corner was useless. This was because the distance between the end points of the dog bone arc were less than the diameter of the router bit. There are many ways this condition could be addressed. I chose to circumscribe a larger arc based on the original angle between the adjacent curves. While it removes more material from the corner, it minimises tool wear and any potential for material to burn.
Single Curve A single curve can now be input into Dog Treat. It will be output with both internal and external treatments.
I’ll continue to update Dog Treat as the need arises, it’s become somewhat of a hobby now. Maybe one day it will become part of a Plug-in… once I learn to code it though!
Happy Treating!
Hi Everyone,
Here's a tool I've been working on for the past 4 months or so in my free time. It's a dog bone corner generator, however it's a little different to some of the existing ones. It's designed to be used for large amounts of geometry and as such, it avoids using any curve boolean operations that are computationally taxing. You don't have to split your curves up into internal and external lots either, it works it all out so you can be lazy. I've also incorporated Lunch Box's Object Bake Component for a one click operation that bakes geometry back out to Internal and External profile layers.
Let me know how it goes, will update where necessary.
Best,
Darcy
Change Log
06/11/19 - Version 2.0 SECOND DINNER - Rebuild
29/09/17 - Version 1.3 - Now with smooth corners option, True for smooth default/False for original
18/05/17 - Version 1.2 - Now includes variable angle domain input (defaults at 90°) for angled corners
13/11/16 - slight change to enable acceptance of very large interior curves
…
Added by Darcy Zelenko at 8:44pm on November 9, 2016
ther math and logic. i can usually conceptualise what i want to do and cobble some semi working thing together but don't know which components to use and how to patch it. so i'm super happy to have someone who knows what he's doing to find this interesting.
and i'm glad you mention the fanned frets again, there is one input parameter that's still missing for the multiscale frets to be fully parametric, it's the angle of the nut or which fret should be straight. it depends a bit on personal preferences and playing posture what is more comfortable. so being able to adjust this easily would be cool. again i have no idea how the maths for that work or if you can just rotate each fret the same amount around it's middle point. The input either as fret number (for the straight fret) or as a simple slider from bridge to nut should do as input setting.
Here are the two extremes and the middle ground:
i've been thinkin today while analysing your patches and cleaning up my mess what exactly the monster should do.
Here are the input parameters needed, i think it's the complete list
scale length low E string
scale length high e string
fret angle/straight fret
string width at nut
string width at bridge
number of frets
fretboard overhang at nut (distance from string to fretboard bounds)
fretboard overhang at last fret
string gauges
string tensions
fretboard radius at nut (for compound radius fretboard radius at bridge is calculated with the stewmac formula)
fretwire crown width
fretwire crown height
action height at nut (distance between bottom of string and fretwire crown top)
action height at last fret
pickup 1 neck position
pickup 2 middle position
pickup 3 bridge position
nut width
the pickup positions should be used to draw circles for the magnet poles on each string so they are perfectly aligned and can be used for the pickup flatwork construction. ideally they would need a rotation control aligning the center line of the pickup so it's somewher between the last fret angle and bridge angle. personally i do this visually depending on the design i'm looking for, some people have huge theories on pickup positioning but personally i don't believe in it.
that should result in everything needed to quickly generate all the necessary construction curves or geometry for nut/fingerboard/frets/pickups. this is the core of what makes a guitar work, the more precise this dynamic system is the better the guitar plays and sounds.
i posted another thread trying to understand how i could use datasets form spreadsheets,databse, csv to organize the input parameters. What would make sense for the strings for example is hook into a spreadsheet with the different string sets, i attached one for the d'Addario NYXL string line which basically covers all combos that make sense.
The string tension is an interesting one, and implmenting it would sure be overkill albeit super interesting to try. it should be possible to extrapolate from the scale length of each string what the tension for a given string gauge of that string would be so that you could say 'i want a fully balanced set' or 'heavy top light bottom) and it would calculate which SKU from d'addario would best match the required tension. All the strings listed in the spreadsheet are available as single strings to buy.
i'm trying to reorganize everything which helps me understand it. i just discovered the 'hidden wires' feature which is great since once i understood what a certain block does or have finished one of my own, i can get the wires out of the way to carry on undistracted. a bit risky to hide so many wires but it makes it so much easier not to get completely lost :-)
btw, the 'fanned fret' term is trademarked, some guy tried to patent it in the 80's which is a bit silly since it has been done for centuries. there is a level of sophistication above this as well, check out http://www.truetemperament.com/ and that really is something else. it really is astounding how superior the tuning is on those wigglefrets, the problem is that it's rather awkward for string bending and also you can't easily recrown or level the frets when they are used. …
e matching with a dedicated component which creates combinations of items. You can find the [Cross Reference] component in the Sets.List panel.
When Grasshopper iterates over lists of items, it will match the first item in list A with the first item in list B. Then the second item in list A with the second item in list B and so on and so forth. Sometimes however you want all items in list A to combine with all items in list B, the [Cross Reference] component allows you to do this.
Here we have two input lists {A,B,C} and {X,Y,Z}. Normally Grasshopper would iterate over these lists and only consider the combinations {A,X}, {B,Y} and {C,Z}. There are however six more combinations that are not typically considered, to wit: {A,Y}, {A,Z}, {B,X}, {B,Z}, {C,X} and {C,Y}. As you can see the output of the [Cross Reference] component is such that all nine permutations are indeed present.
We can denote the behaviour of data cross referencing using a table. The rows represent the first list of items, the columns the second. If we create all possible permutations, the table will have a dot in every single cell, as every cell represents a unique combination of two source list indices:
Sometimes however you don't want all possible permutations. Sometimes you wish to exclude certain areas because they would result in meaningless or invalid computations. A common exclusion principle is to ignore all cells that are on the diagonal of the table. The image above shows a 'holistic' matching, whereas the 'diagonal' option (available from the [Cross Reference] component menu) has gaps for {0,0}, {1,1}, {2,2} and {3,3}:
If we apply this to our {A,B,C}, {X,Y,Z} example, we should expect to not see the combinations for {A,X}, {B,Y} and {C,Z}:
The rule that is applied to 'diagonal' matching is: "Skip all permutations where all items have the same list index". 'Coincident' matching is the same as 'diagonal' matching in the case of two input lists which is why I won't show an example of it here (since we are only dealing with 2-list examples), but the rule is subtly different: "Skip all permutations where any two items have the same list index".
The four remaining matching algorithms are all variations on the same theme. 'Lower triangle' matching applies the rule: "Skip all permutations where the index of an item is less than the index of the item in the next list", resulting in an empty triangle but with items on the diagonal.
'Lower triangle (strict)' matching goes one step further and also eliminates the items on the diagonal:
'Upper Triangle' and 'Upper Triangle (strict)' are mirror images of the previous two algorithms, resulting in empty triangles on the other side of the diagonal line:
…
it seems that was this. Now all is working fine !
Glad that it worked! But I am still a bit worried. Gismo components only modify the gdal-data/osmconf.ini file and no other MapWinGIS file. So your MapWinGIS installation files should not be compromised. The fact that you did not get the "COM CLSID" error message when running the "Gismo Gismo" component suggests that MapWinGIS has been properly installed. So I wonder if the cause for the permanent "invalid shapes" warning has again something with the fact that your system is again not allowing the MapWinGIS to properly edit the osmconf.ini. Maybe this problem will appear again, and again, and reinstallation of MapWinGIS every time can be somewhat bothersome.
- About the terrain generation, is it possible to have the texture from google or other provider mapped onto the terrain surface from gismo component ? (Same as using the ladybug terrain generator in fact). I try to used the image extracted by ladybug component and then applied it to the gismo terrain but the texture is rotated by 90°.
The issue with the rotation can be solved by swapping/reversing the U,V directions of the terrain surface. A slightly more important issue is that terrain surface generated with Gismo "Terrain Generator" component might have a bit smaller radius than what the radius_ input required. This stems from the fact that the terrain data first needs to be downloaded in geographic coordinate system, and then projected. Some projecting issues may occur at the very edges of the projected terrain, so I had to slightly cut out the very edges of the terrain which results in the actual terrain diameters being slightly shorted in both directions. This means that if you apply the same satellite image from Ladybug "Terrain Generator" component to Gismo "Terrain Generator" component the results may not be the same.I attached below a python component which tries to solve this issue by extending the edges of Gismo "Terrain Generator" terrain, and then cutting them with the cuboid of the exact dimensions as the radius_ input. Have in mind that this extension of the original terrain at its edges is not a correct representation of the actual terrain in that location. But rather just an extension of the isoparameteric curve of the terrain surface. So basically: some 0 to 10% (0 to 10 percent of the width and length) of the terrain around all four edges is not the actual terrain for that location, but rather just its extension.The python component is located at the very right of the definition attached below.
Also, if you would like to use the satellite images from Ladybug "Terrain Generator" component along with "OSM shapes", sometimes you may find slight differences in position of the shapes. This is due to openstreetmap data not being based on Google Maps (that's what Ladybug "Terrain Generator" component is using), but rather on Bing, MapQuest and a few others.
- About the requiredKeys_ input of OSM shapes, I understand what you mean and your advice, but in most cases I use it, the component was working fine even without input. I think it's better to extract all tags, values and keys of the selected area, instead of searching for specific ones as I try to find all data related to what I want after, isn't it ? To check what keys are present on the area also.
Ineed, you are correct.I though you were trying to only create a terrain, 3d buildings and maybe find some school or similar 3d building, for these two locations. The recommendation I mentioned previously is due to shapefiles having a limit (2044) to how many keys it can contain. This requires further testing of some big cities locations with maybe larger radii, which I haven't performed due to my poor PC configuration. But in theory, I imagine that it may happen that a downloaded .osm file may have more than 2044 keys. In that case shapefile will only record 2044 of them, and disregard the others. That was my point.But again 2044 is a lot of keys, and I haven't been checking much this in practice. For example, when I set the radius_ to 1000 meters, and use your "3 Rue de Bretonvilliers Paris" location I get around 350 something keys, which is way below the 2044.Another reason why one should use the requiredKeys_ input is to make the Gismo OSM components run quicker: for example, the upper mentioned 350 something keys will result in 350 values for each branch of the "OSM shapes" component's "values" output.Which means if you have 10 000 shapes, the "OSM shapes" component will have 10 000 branches with 350 items on each branch (values). This can make all Gismo OSM components very heavy, and significantly elongate the calculation process.With requiredKeys_ input you may end up with only a couple of tens of items per each branch.Sorry for the long reply.…
Added by djordje to Gismo at 8:57am on June 11, 2017
ating to new speakers.
For more information: https://medium.com/@carspeakerland/a-guide-to-the-simple-way-difference-in-car-speakers-2-way-3-way-4-way-25e0bf215b00
Adding new speakers for your automobile could improve the sound quality dramatically. Some sound technicians say it is the number-one update you may make to improve the overall quality of your vehicle.
"They do not care how it sounds. Speakers are often form of continue on the list. Updating to new speakers offers you a much fuller sound."
There is a whole lot to pick from in regards to car speakers. (Photo from Eldon Lindsay)
"New speakers will make a greater fidelity and clarity of sound," states Robert Nevitt, proprietor of Audio Electronics at Indianapolis. "The audio is more different without distortion. People will not get bored listening to it."
Cook says customers need to pick the type of sound they enjoy. The very first thing Cook does having a customer is sit in the car together to talk about their personal taste.
"Everybody's ear is different," he states. "That which I believe sounds great, you might believe is dreadful. It is a fantastic idea to get outside and listen to everything you enjoy and do not like about doing it."
When you've discovered a sound you want, you are going to discover the sky's actually the limitation in regards to purchasing car speakers. There are scores of manufactures and models, sizes and power levels to select from.
Columbus Car Audio & Accessories offers three types of automobile speakers to pick from: complete array speakers, component speakers along with coaxial speakers.
• Total range speakers arrive with a tweeter to make to your high-pitched sounds along with a woofer for those lows. This option offers a number of different sizes.
• Unit speakers, nonetheless, include separate tweeters and woofers.
• Coaxial speakers arrive with a tweeter plus motorist.
When you've selected a type of automobile speaker, you are going to want to determine how many you desire. Cook states some cars arrive with as little as just two speakers, whereas bigger, luxury vehicles might have too many 32. He adds a normal sedan generally has four. What are The Speaker Sizes in My Car | Speaker Size for My Car
"It simply depends if you would like to replace all of these," Cook says. "I would advise doing all of four. If you are budget-minded, I'd begin with the ones at the front. That is where you are at. And you are likely to be at the automobile 100 percent of their moment."
Subwoofers are designed to reproduce low bass frequencies also may be included with new speakers or could be added separately to existing car speakers.
"Many speakers can not play down low in these frequencies such as a subwoofer may," Cook says.
Related Article
Wondering about speakers? Below are a few techniques to establish a home entertainment experience whatever your budget.
A speaker update might charge as little as $100 up to a few million dollars depending on the scope of job and type of speaker.
Cook states that the price of a subwoofer can operate as low as $37. Columbus Car Audio & Accessories sells a subewoofer bundle that includes an amplifier and a enclosure for about $ 299.
To get a set of automobile speakers, Columbus Car Audio & Accessories begin prices at $39, with an average price tag of about $70 for setup. Adding an anti-vibrator into a set of speakers prices an additional $25.
Nevitt, meanwhile, fees as little as $99 to get a set of "some good speakers." The price of one hour of installion, that is typically how long it takes to put in a set of speakers, is 67.
However, most customers spend far more.
"Paying a total amount of 800 to $1000 isn't from this world of possibility," Nevitt states. "A price somewhere in the center could be $400 or $500."
Cook says several vehicle speaker technicians began with DIY projects and adds there is nothing wrong with trying to set up car speakers all on your own. But you are going to want the correct tools for your job along with just a little understand. Installing speakers requires carrying out your car door.
See Also: https://www.scoop.it/t/how-to-choose-best-car-speakers-6x9-inch-6-5-inch-6x8-inch-4-inch
Choosing a professional to set up speakers ensures that the job is done correctly.
"If you do it yourself, then you might wind up breaking something. That is some thing we do everyday. I am not planning to inform you we will not violate something. But we will look after it if we perform. We all do so with being honest and up front with people."
If you are getting speakers set up, experts say to expect to place an appointment to the setup. …
greatly appreciate it!!
You can write the number of the question and write your answer next to it, example:
1) a
2) c
3) a) Washington University in St. Louis
4) 2 weeks (1week+1week shipping)
5) 130
6) b
7) b
The survey questions are as follows:
1)
Did you 3D print before?
5)
How much did it cost (in dollars)?
a.
Yes, for a school project
a.
Between 20 & 50
b.
Yes, for a personal project
b.
Between 50 & 80
c.
Between 80 & 120
2)
Print size
d.
Please specify if otherwise: _____ dollars
a.
Between 2 & 6 cubic inches
b.
Between 6 & 12 cubic inches
6)
Do you think the price was expensive?
c.
Between 12 & 20 cubic inches
a.
Not at all
d.
Please specify if otherwise: ____cubic inches
b.
A little bit expensive
c.
Very expensive
3)
Where did you print your object?
a.
School
7)
Were you satisfied with the printed object?
b.
Outside school: _________________
a.
Yes, it was a great print without problems
b.
Not bad, some issues
4)
How long did it take to print?
c.
I was not satisfied, very bad quality
a.
___ days
b.
___ weeks
Thank you very much to all!!
PS: If you did many 3D prints, you can post multiple answers.
Wassef…
whole design intent, but this is what Inventor is good at. The way it packages bits of 'scripted' components into 'little models' that can be stored and re-assembled is central to MCAD working.
The Inventor model shown is almost 5 years old. We don't model like that any more, however it does offer a good idea of general MCAD modeling approaches.
iParts is useful in certain situations, it could've been useful in the above model, its usefulness is often in function of the quantity of variants/configurations.
So much is scripted in GH, maybe it should also be possible to script/define/constrain/assist the placement/gluing of the results?
...
Starting point: I think we are talking across purposes. AFAIK, the solving sequence of GH's scripted components is fixed. It won't do circular dependencies... without a fight. The inter-component dependencies not 'managed' like constraints solvers do for MCAD apps.
Components and assemblies are individual files in MCAD.
Placement of these within assemblies in MCAD is a product of matrix transforms and persistent constraints. There is no bi-directional link, the link is unidirectional (downflow only), because of the use of proxies.
Consequently, scripting the placement of components is irrelevant in GH, unless you decide that each component needs to be contained in its own separate file.
This also brings up the point that generating components and assemblies in MCAD is not as straightforward. In iParts and iAssemblies, each configuration needs to be generated as a "child" (the individual file needs to be created for each child) before those children can be used elsewhere.
You notice the dilemma, if you generate 100 parts, and then you realize you only need 20, you've created 80 extra parts which you have no need for, thus generating wasteful data that may cause file management issues later on.
GH remains in a transient world, and when you decide to bake geometry (if you need to at all), you can do that in one Rhino file, and save it as the state of the design at that given moment. Very convenient for design, though unacceptable for most non-digital manufacturing methods, which greatly limits Rhino's use for manufacturing unless you combine it with an MCAD app.
One of the reasons why the distributed file approach makes perfect sense in MCAD, is that in industry you deal with a finite set of objects. Generative tools are usually not a requirement. Most mechanical engineers, product engineers and machinists would never have any use for that.
The other thing that MCAD apps like Inventor have, is the 'structured' interface that offers up all that setting out information like the coordinate systems, work planes, parameters etc in a concise fashion in the 'history tree'. This will translate into user speed. GH's canvas is a bit more freeform. I suppose the info is all there and linked, so a bit of re-jigging is easy. Also, see how T-Flex can even embed sliders and other parameter input boxes into the model itself. Pretty handy/fast to understand, which also means more speed.
True. As long as you keep the browser pane/specification tree organized and easy to query.
:)
Would love to understand what you did by sketching.
I'll start by showing what was done years ago in the Inventor model, and then share with you what I did in GH, but in another post.
Let's use one of the beams as an example:
We can isolate this component for clarity.
Notice that I've highlighted the sectional sketch with dimensions, and the point of reference, which is in relation to the CL of the column which the beam bears on. The orientation and location of the beam is already set by underlying geometry.
Here's a perspective view of the same:
The extent of the beam was also driven by reference geometry, 2 planes offset from the beam's XY plane, driven by parameters from another underlying file which serves as a parameter container:
Reference axes and points are present for all other components, here are some of them:
It starts getting cluttered if you see the reference planes as well:
Is I mentioned earlier, over time we've found better ways to define and associate geometry, parameters, manage design change, improving the efficiency of parametric models. But this model is a fair representation of a basic modeling approach, and since an Inventor-GH comparison is like comparing apples and oranges anyways, this model can be used to understand the differences and similarities, for those interested.
I haven't even gotten to your latest post yet, I will eventually.…
Added by Santiago Diaz at 10:36am on February 26, 2011
edit 29/04/14 - Here is a new collection of more than 80 example files, organized by category:
KangarooExamples.zip
This zip is the most up to date collection of examples at the moment, and collects t
oftware connections built from the initial seed of the project. As always you can download the new release from Food4Rhino. Make sure to remove the older version of Ladybug and Honeybee and update your scripts.
This release is also special since today it is just about 3 years (3 years and 2 weeks) from the first release of Ladybug. As with any release, there have been a number of bug fixes and improvements but we also have some major news this time. In no specific order and to ensure that the biggest developments do not get lost in the extensive list of updates, here are the major ones:
Mostapha is re-writing Ladybug!
Ladybug for DynamoBIM is finally available.
Chris made bakeIt really useful by incorporating an export pathway to PDFs and vector-based programs.
Honeybee is now connected to THERM and the LBNL suite thanks to Chris Mackey.
Sarith has addressed a much-desired wish for Honeybee (Hi Theodore!) by adding components to model electric lighting with Radiance.
Djordje is on his way to making renewable energy deeply integrated with Ladybug by releasing components for modeling solar hot water.
There is new bug. Check the bottom of the post for Dragonfly!
Last but definitely not least (in case you’re not still convinced that this release is a major one) Miguel has started a new project that brings some of Ladybug’s features directly to Rhino. We mean Rhino Rhino - A Rhino plugin! Say hi to Icarus! #surprise
Before we forget! Ladybug and Honeybee now have official stickers. Yes! We know about T-Shirts and mugs and they will be next. For now, you can deck-out your laptops and powerhouse simulation machines with the symbology of our collaborative software ecosystem.
Now go grab a cup of tea/coffee and read the details below:
Rewriting Ladybug!
Perhaps the most far-reaching development of the last 4 months is an effort on the part of Mostapha to initiate a well structured, well documented, flexible, and extendable version of the Ladybug libraries. While such code is something that few community members will interact with directly, a well-documented library is critical for maintaining the project, adding new features, and for porting Ladybug to other software platforms.
The new Ladybug libraries are still under development across a number of new repositories and they separate a ladybug-core, which includes epw parsing and all non-geometric functions, from interface-specific geometry libraries. This allows us to easily extend Ladybug to other platforms with a different geometry library for each platform (ie. ladybug-grasshopper, ladybug-dynamo, ladybug-web, etc) all of which are developed on top of the ladybug-core.
Without getting too technical, here is an example of a useful outcome of this development. If you want to know the number of hours that relative humidity is more than 90% for a given epw, all that you have to code (in any python interface) is the following:
import ladybug as lb
_epwFile = r"C:\EnergyPlusV7-2-0\WeatherData\USA_CO_Golden-NREL.724666_TMY3.epw"
epwfile = lb.epw.EPW(_epwFile)
filteredData = epwfile.relativeHumidity.filterByConditionalStatement('x>90')
print "Number of hours with Humidity more than 90 is %d "%len(filteredData.timeStamps)
Compare that to the 500 + lines that you would have had to write previously for this operation, which were usually tied to a single interface! Now let’s see what will happen if you want to use the geometry-specific libraries. Let’s draw a sunpath in Grasshopper:
import ladybuggrasshopper.epw as epw
import ladybuggrasshopper.sunpath as sunpath
# get location data form epw file
location = epw.EPW(_epwFile).location
# initiate sunpath based on location
sp = sunpath.Sunpath.fromLocation(location, northAngle = 0, daylightSavingPeriod = None, basePoint =cenPt, scale = scale, sunScale = sunScale)
# draw sunpath geometry
sp.drawAnnualSunpath()
# assign geometries to outputs
...
Finally we ask, how would this code will look if we wanted to make a sunpath for dynamo? Well, it will be exactly the same! Just change ladybuggrasshopper in the second line to ladybugdynamo! Here is the code which is creating the sunpath below.
With this ease of scripting, we hope to involve more of our community members in our development and make it easy for others to use ladybug in their various preferred applications. By the next release, we will produce an API documentation (documentation of all the ladybug classes, methods and properties that you can script with) and begin making tutorials for those interested in getting deeper into Ladybug development.
LADYBUG
1 - Initial Release of Ladybug for Dynamo:
As is evident from the post above, we are happy to announce the first release of Ladybug for Dynamo! You can download the ladybug package from Dynamo package manager. Make sure to download version 0.0.6 which is actually 0.0.1! It took a number of trial and errors to get it up there. Once you have the file downloaded you can watch these videos to get started:
The source code can be find under ladybug-dynamo repository and (as you can already guess) it is using the new code base. It includes a very small toolkit of essential Ladybug components/nodes but it has enough to get you started. You can import weather files, draw sunpaths and run sunlighthours or radiation analyses.
There are two known issues in this release but neither of them is critical. You need to have Dynamo 0.9.1 or higher installed which you can download from here (http://dynamobuilds.com/). It is recommended that you run the scripts with ‘Manual’ run (as opposed to ‘Automatic’) since the more intense calculations can make Dynamo crash in automatic mode.
To put things in perspective, here is how we would map Ladybug for Dynamo vs Ladybug and Honeybee for Grasshopper on the classic ‘Hype graph’. The good news is that what we learned a lot from the last three years, making development of the Dynamo version easier and getting us to the plateau of productivity faster.
We should also note that the current development of the Dynamo interface is behind that of the Ladybug-Core, which means there are a number of features that are developed in the code but haven’t made their way to the nodes yet. They will be added gradually over the next month or two.
If you’re interested to get involved in the development process or have ideas for the development, follow ladybug on Facebook, Twitter and Github. We will only post major release news here. Facebook, github and twitter will be the main channels for posting the development process. There will also be a release of a new ladybug for Grasshopper soon that will use the came Ladybug-Core libraries as the Dynamo interface [Trying hard not to name it as Ladybug 2].
2 - New Project “Icarus” Provides Ladybug Capabilities Directly in Rhino
Speaking of expanded cross-platform capabilities, the talented Miguel Rus has produced a standalone Rhino Plugin off of the original Ladybug code that has been included in this release. After writing his own core C# libraries, Miguel’s plugin enables users to produce sunpath and run sunlight hours analyses in the Rhino scene without need of opening Grasshopper or engaging the (sometimes daunting) act of visual scripting.
This release includes his initial RHP plugin file. It is hoped that Miguel’s efforts will extend some of the capabilities of environmental design to individuals who are unfamiliar with visual scripting, casting the network of our community into new territory. We need your help spreading the word about Icarus since the people who will benefit the most from it have probably not read this far into the release notes. Also, as the project is in the early stages, your feedback can make a great difference. You can download the current release from this link.
Once you download the zip file. Right click and unblock it. Then extract the files under C:\Program Files\Rhinoceros 5 (64-bit)\Plug-ins\ folder. Drag and drop the RHP file into Rhino and you should be ready to go. You can either type Icarus in the command line or open it via the panels. Here is a short video that shows how to run a sunlighhours analysis study in Rhino.
3 - BakeIt Input Now Supports a Pathway to PDF +Vector Programs
As promised in the previous release, the BakeIt_ option available on Ladybug’s visual components has been enhanced to provide a full pathway to vector-based programs (like Illustrator and Inkscape) and eases the export to vector formats like PDFs.
This means that the BakeIt_ operation now places all text in the Rhino scene as actual editable text (not meshes) and any colored meshes are output as groups of colored hatches (so that they appear as color-filled polygons in vector-based programs). There is still an option to bake the colored geometries as light meshes (which requires smaller amounts of memory and computation time) but the new hatched capability should make it easier to incorporate Ladybug graphics in architectural drawings and documents like this vector psychrometric chart.
4 - Physiological Equivalent Temperature (PET) Now Available
Thanks to the efforts of Djordje Spasic, it is now possible to compute the common outdoor comfort metric ‘Physiological Equivalent Temperature’ (PET) with Ladybug. The capability has been included with this release of “Thermal Comfort Indices” component and is supported by a “Body Characteristics” component in the Extra tab. PET is particularly helpful for evaluating outdoor comfort at a high spatial resolution and so the next Honeybee release will include an option for PET with the microclimate map workflow.
5 - Solar Hot Water Components Available in WIP
Chengchu Yan and Djordje Spasic have built a set of components that perform detailed estimates of solar hot water. The components are currently undergoing final stages of testing and are available in the WIP tab of this release. You can read the full release notes for the components here.
6 - New Ladybug Graphic Standards
With the parallel efforts or so many developers, we have made an effort in this release to standardize the means by which you interact with the components. This includes warnings for missing inputs and the ability to make either icons or text appear on the components as you wish (Hi Andres!). A full list of all graphic standards can be found here. If you have any thoughts or comments on the new standards, feel free to voice them here.
7 - Wet Bulb Temperature Now Available
Thanks to Antonello Di Nunzio - the newest member of the Ladybug development team, it is now possible to calculate wet bulb temperature with Ladybug. Antonello’s component can be found under the WIP tab and takes inputs of dry bulb temperature, relative humidity, and barometric pressure.
8 - New View Analysis Types
The view analysis component now allows for several different view studies in addition to the previous ‘view to test points.’ These include, skyview (which is helpful for studies of outdoor micro-climate), as well as spherical view and ‘cone of vision’ view, which are helpful for indoor studies evaluating the overall visual connection to the outdoors.
HONEYBEE
1 - Connection to THERM and LBNL Programs
With this release, many of you will notice that a new tab has been added to Honeybee. The tab “11 | THERM” includes 7 new components that enable you to export ready-to-simulate Lawrence Berkeley National Lab (LBNL) THERM files from Rhino/Grasshopper. THERM is a 2D finite element heat flow engine that is used to evaluate the performance of wall/window construction details by simulating thermal bridging behavior. The new Honeybee tab represents the first ever CAD plugin interface for THERM, which has been in demand since the first release of LBNL THERM several years ago. The export workflow involves the drawing of window/wall construction details in Rhino and the assigning of materials and boundary conditions in Grasshopper to produce ready-to-simulate THERM files that allow you to bypass the limited drawing interface of THERM completely. Additional components in the “11 | THERM” tab allow you to import the results of THERM simulations back into Grasshopper and assist with incorporating THERM results into Honeybee EnergyPlus simulations. Finally, two components assist with a connection to LBNL WINDOW for advanced modeling of Glazing constructions. Example files illustrating many of the capabilities of the new components can be found in there links.
THERM_Export_Workflow, THERM_Comparison_of_Stud_Wall_Constructions
Analyze_THERM_Results, Thermal_Bridging_with_THERM_and_EnergyPlus
Import_Glazing_System_from_LBNL_WINDOW, Import_LBNL_WINDOW_Glazing_Assembly_for_EnergyPlus
It is recommended that those who are using these THERM components for the first time begin by exploring this example file.
Tutorial videos on how to use the components will be posted soon. A great deal of thanks is due to the LBNL team that was responsive to questions at the start of the development and special thanks goes to Payette Architects, which allowed Chris Mackey (the author of the components) a significant amount of paid time to develop them.
2 - Electrical Lighting Components with Enhanced Capabilities for Importing and Manipulating IES Files
Thanks to the efforts of Sarith Subramaniam, it is now much easier and more flexible to include electric lighting in Honeybee Radiance simulations. A series of very exciting images and videos can be found in his release post.
You can find the components under WIP tab. Sarith is looking for feedback and wishes. Please give them a try and let him know your thoughts. Several example files showing how to use the components can be found here. 1, 2, 3.
3- Expanded Dynamic Shade Capabilities
After great demand, it is now possible to assign several different types of control strategies for interior blinds and shades for EnergyPlus simulations. Control thresholds range from zone temperature, to zone cooling load, to radiation on windows, to many combinations of these variables. The new component also features the ability to run EnergyPlus simulations with electrochromic glazing. An example file showing many of the new capabilities can be found here.
Dragonfly Beta
In order to link the capabilities of Ladybug + Honeybee to a wider range of climatic data sets and analytical tools, a new insect has been initiated under the name of Dragonfly. While the Dragonfly components are not included with the download of this release, the most recent version can be downloaded here. An example file showing how to use Dragonfly to warp EPW data to account for urban heat island effect can also be found here. By the next release, the capabilities of Dragonfly should be robust enough for it to fly on its own. Additional features that will be implemented in the next few months include importing thermal satellite image data to Rhino/GH as well as the ability to warp EPW files to account for climate change projections. Anyone interested in testing out the new insect should feel free to contact Chris Mackey.
And finally, it is with great pleasure that we welcome Sarith and Antonello to the team. As mentioned in the above release notes, Sarith has added a robust implementation for electric light modeling with Honeybee and Antonello has added a component to calculate wet bulb temperature while providing stellar support to a number of people here on the GH forum.
As always let us know your comments and suggestions.
Enjoy!
Ladybug+Honeybee development team
PS: Special thanks to Chris for writing most of the release notes!…