as passing this extra check and because of that it was running faster. It doesn't mean that the first analysis is totally wrong as it depends on the analysis case and should be checked and optimized before running the final analysis.
You can read more about radiance parameters here (http://radsite.lbl.gov/radiance/refer/Notes/rpict_options.html), and here (http://radiance-online.org/community/workshops/2011-berkeley-ca/pre...). Since you have a light-shelf I suggest you to add to the number of ambient bounces (ab).
Now back to your wish to have the analysis run faster you can comment the line hb_writeRADAUX.checkInputParametersForGridBasedAnalysis() inside Honeybee_runDaylightSimulation and it won't overwrite the initial values but make sure that you run a number of test cases and compare the results between the runs.
Back to your definition, it looks good to me. You could have saved yourself some time by using MassToZone component and then just adding the ceiling separately but there's nothing wrong with your approach.
The main place in the definition that can change is how you're generating the vertical fins. I imagine you can use a single set of components to generate every group of the fins but again your definition will work.
I updated your file to the latest version, which means you also need to update Honeybee and Ladybug in case you're looking to modify the file.
Hope it helps,
Mostapha…
ace when I start running Galapagos/Octopus (below is "room orientation optimization" shared at http://hydrashare.github.io/hydra/viewer?owner=mostaphaRoudsari&fork=hydra_1&id=Room_Orientation_Optimization&slide=0&scale=1&offset=0,0) It may take quite some time to see some results. That's fine for the above simulation. But my real challenge is, when I am going to optimize room dimension with respect to ASE and sDA calculations, either Galapagos or Octopus goes wildly and never come up with a solution. I believe the time-consuming calculation, especially sDA with higher -ab numbers, trigger the lag a lot? Any suggestion/trick to improve it?
Most importantly, based on your experience, for example to optimize window/exterior shades sizes and achieve ASE<10% and sDA>55% (LEED v.4 requirements), Octopus (due to its capacity of multiple objectives) is the only choice? Any other approaches within grasshopper?
The alternative approach in my mind as a GH beginner is as follows. But I am not sure whether it is doable. Again, your comments will be greatly appreciated.
Since all my room/window/shades dimension are controlled by number sliders, I am thinking whether a component from GH will trigger these number sliders (not necessary to be all of them but one by one) automatically. If this is possible, I can do "data recorder" to record outputs from ASE and sDA. Eventually I will have a database of the input parameters and sDA/ASE results.
Does it make sense? Is there a component which can trigger number slider output at certain step?
Many thank!
Cheney …
GH, same as using sweep2 command in Rhino.
The one on the right is what I got so far (the output smooth our the kink of the original rails). Basically I am just following the methods provided by sdk sample: http://wiki.mcneel.com/developer/sdksamples/sweep2 .
The following is the function I copy and use directly from the SDK sample. By using this function, I can generate the sweep surface at right. But I want to have is the one in the middle with the kink edges. Can anyone show me how and where to modify he settings? I guess some sweep arguments need to be changed? I have try couples, such m_simplify, m_bSimpleSweep, m_bSameHeight, m_rebuild_count... but still cannot find a right combination for this function to output the sweep surface I want. Any suggestions or helps are very appreciated. Thanks for your help and time on this.
'Sweep2 function'----------------
Sub Sweep2( ByVal Rail1 As IOnCurve, _
ByVal Rail2 As IOnCurve, _
ByVal sCurves As List(Of IOnCurve), _
ByRef Sweep2_Breps As List(Of OnBrep))
'Define a new class that contains sweep2 arguments
Dim args As New MArgsRhinoSweep2
'Set the 2 rails
Dim Edge1 As New MRhinoPolyEdge
Dim Edge2 As New MRhinoPolyEdge
Edge1.Append(Rail1.DuplicateCurve())
Edge2.Append(Rail2.DuplicateCurve())
'Add rails to sweep arguments
args.m_rail_curves(0) = Edge1
args.m_rail_curves(1) = Edge2
args.m_bClosed = False
Dim section_curves As New List(Of OnCurve)
'Loop through sections to set parameters
For Each Section As IOnCurve In sCurves
Dim sCurve As OnCurve = Section.DuplicateCurve()
section_curves.Add(sCurve)
Dim t0 As Double = 0
If Not Edge1.GetClosestPoint(sCurve.PointAtStart(), t0) Then
If Not Edge1.GetClosestPoint(sCurve.PointAtEnd(), t0) Then
Dim s As Double = 0
sCurve.GetNormalizedArcLengthPoint(0.5, s)
Edge1.GetClosestPoint(sCurve.PointAt(s), t0)
End If
End If
args.m_rail_params(0).Append(t0)
Dim t1 As Double = 0
If Not Edge2.GetClosestPoint(sCurve.PointAtStart(), t1) Then
If Not Edge2.GetClosestPoint(sCurve.PointAtEnd(), t1) Then
Dim s As Double = 0
sCurve.GetNormalizedArcLengthPoint(0.5, s)
Edge2.GetClosestPoint(sCurve.PointAt(s), t1)
End If
End If
args.m_rail_params(1).Append(t1)
Next
'Set shapes
args.m_shape_curves = section_curves.ToArray
'Set the rest of parameters
args.m_simplify = 0
args.m_bSimpleSweep = False
args.m_bSameHeight = False
args.m_rebuild_count = -1 'Sample point count for rebuilding shapes
args.m_refit_tolerance = RMA.Rhino.RhUtil.RhinoApp.ActiveDoc.AbsoluteTolerance()
args.m_sweep_tolerance = RMA.Rhino.RhUtil.RhinoApp.ActiveDoc.AbsoluteTolerance()
args.m_angle_tolerance = RMA.Rhino.RhUtil.RhinoApp.ActiveDoc.AngleToleranceRadians()
Dim sBreps() As OnBrep = Nothing
If (RhUtil.RhinoSweep2(args, sBreps)) Then
For Each b As OnBrep In sBreps
Sweep2_Breps.Add(b)
Next
End If
Return
End Sub
…
ect + Geco
TUTORS:
Arturo Tedeschi (Authorized Rhino Trainer) + Maurizio Arturo Degni
Il workshop avanzato ECOLOGIC PATTERNS affronta l’impiego di strategie parametriche all’interno del processo progettuale, approfondendo l’utilizzo di Grasshopper in sinergia con plug-in, software di analisi ambientale e simulazione fisica. Obiettivo fondamentale è la generazione della forma come risultato di tecniche di form-finding e di input ambientali (solari, termici e acustici). Verranno acquisiti nuovi strumenti operativi e di simulazione al fine di costruire modelli parametrici ottimizzati in grado di adattarsi a diverse condizioni di contesto.
MORE INFO…
ive collaborative environment.
TYPE : Course module and Workshop
The event is open for anybody interested from all the fields of design, including: architecture, interior design, furniture design, product design, fashion design, scenography, and engineering.
1. COURSE MODULE (20-23 April 2014) - optional
+ type: 3 days intensive course regarding basic knowledge in parametric design (LEVEL 1)
+ software: Rhinoceros & Grasshopper
+ plugins: Kangaroo, Weaver Bird, Lunch box, Ghowl, Geco
+ achievements:
- acquainting to the components & the concept of Generative Design
- understanding the strategies in Algorithmic Design
- how to easily insert simple mathematical equation into the project to gain more control
- how to utilize proper plugins with respect to their nature of the project
- interacting with different analysis platforms such as Ecotect & remote controller
- solving several exercises with different scales( 2D- 3D ) during each phase of the workshop
2. WORKSHOP (23-27 April 2014)
A 5 day Design-Based Research Workshop exploring new techniques in Digital Architecture/Fabrication, with a specific focus on the use of generative systems and parametric modeling as tools for creative expression.
Our ultimate goal is to increasing the efficiency of utilizing digital tools in parallel with geometric performance of the primitive design agent.
+ + CONCEPT
Fashion and Architecture are both based on basic life necessities – clothing and shelter.
However, they are also forms of self-expression – for both creators and consumers.
Both fashion and architecture affect our emotional being in many ways.
The agenda of this workshop is to investigate on the overlap between these two areas of design, art & fashion.
Fashion and architecture express ideas of personal, social and cultural identity, reflecting the concerns of the user and the ambition of the age. Their relationship is a symbiotic one and throughout history, clothing and buildings have echoed each other in form and appearance. This only seems natural as they not only share the primary function of providing shelter and protection for the body, but also because they both create space and volume out of flat, two-dimensional materials.
While they have much in common, they are also intrinsically different – address the human scale, but the proportions, sizes and shapes differ enormously.
+ + + OBJECTIVES
So far, Architects have been using techniques such as folding, bending etc. to create space, structural roofs or different other structural shapes.
The agenda of this workshop goes further with the investigation of algorithmic thinking through generative tools Integrated in design.
The challenge is creating a bridge that connects these two areas of design, architecture and fashion that perform at two opposite scales.
+ + + + TECHNICAL BRIEF
In the early stages physical models and low-tech strategies will be used, allowing the participants to gain a greater understanding of materials, fabrication and assembly methods as well as simple, yet pragmatic structural solutions.
Later in the workshop these strategies will be digitalized and elaborated using software visualizing tools such as Rhinoceros and the algorithmic plug-in Grasshopper.…
(1) I have been exporting small sections of a larger model into Maya from Rhino as FBX. In Maya I rotate and scale the models (-90 in X, Scale XYZ 0.001). The Named Views are being saved, but do not have a successful import into the Maya model. They do not appear as in Rhino, and the problem is not solved by scaling or rotating the cameras.
(2) If I try going the other direction, the cameras exported from Maya as FBX are also not aligning with the model in Rhino as they are in Maya.. I will do my best to post some images of the problem and hope you can help.
error !!
This is what the named views look like
here I am trying to the other way with a good view from Maya
strange placement..
This is the best result I can achieve, after I scale the camera by 1000
Any Advice???
Thanks, Robert.
…
ysim.ning.com/
When you run the simualtion you will notice on the batch terminal that Daysim is also being called, so you may want to consider how Daysim uses Radiance files & data.
Regarding your current problem, I think you stumbled onto something weird and interesting.
Interior and exterior readings appear to differ by 40 in the best case scenarios. Even setting the transmittance to 1 yields similar results. I tried changing from cummulative sky to climate sky and got similar values. Changing the test points did nothing either.
I think, (yet I'm too lazy to prove this) that the difference in values stems from diffuse radiation over the sky dome.
If you delete everything except the glass you'll notice that interior values are like 80-90% of the exterior values (this seems like the expected behaviour with a transmittance of 1). So, if we consider that a vertical window, part of an opaque box, is receiving radiation from 25% of a sphere, as you start to inset the interior test points the radiation they receive will be a fraction of the 25%.
Let me try to explain this better...The exterior surface receives radiation from a section of a sphere calculated by 180degrees on the xy plane (let’s call this angle theta) and by 90degrees (let’s call this angle phi) in azimuthal elevation. If you integrate this over spherical coordinates (theta from 0 to pi; phi from 0 to pi/2) you will find that it comes to a quarter of a sphere. By comparison, the interior surface will not integrate theta from 0 to 180degrees,nor phi from 0 to 90degrees, instead it will be the subtended angle from the exterior surface as a function of their separation; the farther in you go the smaller the view of the outside.
If my hypothesis is correct there shouldn't be that much difference since the separation is only 10cms...the subtended angle would be like 170 instead of 180 for theta and 85 instead of 90 for phi...overall if you integrate both spherical areas there should only by a difference of 10%.
In conclusion, I believe the unexpected behaviour stems from the previous subtended angle thing. If direct radiation was the only factor the difference would be the aforementioned 10%, which suggests that an additional source of energy is also affected by this. Perhaps indirect and diffuse radiation from other areas of the sky dome.
I’m definitely intrigued on why this is happening. Please post if you figure it out.
Regards,
Mauricio
…
ed file and code below:
Color ColorAt(Mesh mesh, int faceIndex, double t0, double t1, double t2, double t3) { // int rc = -1; var color = Rhino.Display.Color4f.Black;
if( mesh.VertexColors.Count != 0) { // test to see if face exists if( faceIndex >= 0 && faceIndex < mesh.Faces.Count ) { /// Barycentric quad coordinates for the point on the mesh /// face mesh.Faces[FaceIndex].
/// If the face is a triangle /// disregard T[3] (it should be set to 0.0).
/// If the face is /// a quad and is split between vertexes 0 and 2, then T[3] /// will be 0.0 when point is on the triangle defined by vi[0], /// vi[1], vi[2]
/// T[1] will be 0.0 when point is on the /// triangle defined by vi[0], vi[2], vi[3].
/// If the face is a /// quad and is split between vertexes 1 and 3, then T[2] will /// be -1 when point is on the triangle defined by vi[0], /// vi[1], vi[3]
/// and m_t[0] will be -1 when point is on the /// triangle defined by vi[1], vi[2], vi[3].
MeshFace face = mesh.Faces[faceIndex];
// Collect data for barycentric evaluation. Color p0, p1, p2;
if(face.IsTriangle) { p0 = mesh.VertexColors[face.A]; p1 = mesh.VertexColors[face.B]; p2 = mesh.VertexColors[face.C]; } else { if( t3 == 0 ) { // point is on subtriangle {0,1,2} p0 = mesh.VertexColors[face.A]; p1 = mesh.VertexColors[face.B]; p2 = mesh.VertexColors[face.C]; } else if( t1 == 0 ) { // point is on subtriangle {0,2,3} p0 = mesh.VertexColors[face.A]; p1 = mesh.VertexColors[face.C]; p2 = mesh.VertexColors[face.D]; //t0 = t0; t1 = t2; t2 = t3; } else if( t2 == -1 ) { // point is on subtriangle {0,1,3} p0 = mesh.VertexColors[face.A]; p1 = mesh.VertexColors[face.B]; p2 = mesh.VertexColors[face.D]; //t0 = t0; //t1 = t1; t2 = t3; } else { // point must be on remaining subtriangle {1,2,3} p0 = mesh.VertexColors[face.B]; p1 = mesh.VertexColors[face.C]; p2 = mesh.VertexColors[face.D]; t0 = t1; t1 = t2; t2 = t3; } }
/** double r = t0 * p0.FractionRed() + t1 * p1.FractionRed() + t2 * p2.FractionRed(); double g = t0 * p0.FractionGreen() + t1 * p1.FractionGreen() + t2 * p2.FractionGreen(); double b = t0 * p0.FractionBlue() + t1 * p1.FractionBlue() + t2 * p2.FractionBlue();
ON_Color color; color.SetFractionalRGB(r, g, b);
unsigned int abgr = (unsigned int)color; rc = (int) ABGR_to_ARGB(abgr); **/ var c0 = new Rhino.Display.Color4f(p0); var c1 = new Rhino.Display.Color4f(p1); var c2 = new Rhino.Display.Color4f(p2); float s0 = (float) t0; float s1 = (float) t1; float s2 = (float) t2;
float R = s0 * c0.R + s1 * c1.R + s2 * c2.R; float G = s0 * c0.G + s1 * c1.G + s2 * c2.G; float B = s0 * c0.B + s1 * c1.B + s2 * c2.B; color = new Rhino.Display.Color4f(R, G, B, 1); } } return color.AsSystemColor(); }
…
Introduzione a Grasshopper", il primo manuale su Grasshopper.
.
I corsi PLUG IT nascono dalla volontà di promuovere le nuove tecnologie digitali di supporto alla progettazione e condividere il know-how maturato attraverso ricerca, collaborazione con i più importanti studi di architettura e pubblicazioni internazionali.
.
Verranno introdotte le nozioni base di Grasshopper approfondendo le metodologie della progettazione parametrica e le tecniche di modellazione algoritmica per la generazione di forme complesse. Il corso è rivolto a studenti e professionisti con esperienza minima nella modellazione 3D e si articolerà in lezioni teoriche ed esercitazioni.
. Argomenti trattati:
- Introduzione alla progettazione parametrica: teoria, esempi, casi studio - Grasshopper: concetti base, logica algoritmica, interfaccia grafica - Nozioni fondamentali: componenti, connessioni, data flow
- Funzioni matematiche e logiche, serie, gestione dei dati - Analisi e definizione di curve e superfici
- Definizione di griglie e pattern complessi - Trasformazioni geometriche, paneling - Attrattori, image sampler
- Data tree: gestione di dati complessi - Digital fabrication: teoria ed esempi - Nesting: scomposizione di oggetti tridimensionali in sezioni piane per macchine CNC
.
Verrà rilasciato un attestato finale.
.
Ulteriori info e programma completo su: www.arturotedeschi.com e su www.edizionilepenseur.it…