he TOF and TSRF indices. They show, how "distant" is your _PV_SWHsurface from the optimal _PV_SWHsurface surface in terms of tilt and azimuth angles.However, in your case we are not interested in TOF and TSRF indices. We would just like to know what are the _PV_SWHsurface optimal tilt and azimuth angles, regardless of the supplied _PV_SWHsurface.
So the circular surface supplied to the "TOF" component's _PV_SWHsurface input is irrelevant. It can be of any area, and any tilt/azimuth angle.The PV_SWHsurfacesArea output of the "PV SWH system size" component depends on a couple of factors:moduleActiveAreaPercent_ (leave it at 90%).
moduleEfficiency_,
systemSize_.Calculation of systemSize_ depends on your electricity demand, cost of the PV system, type of the object, country, local regulations etc. This is something that an engineer needs to determine.For example, in USA for a residential house in the Sunbelt, depending on finances, a household would try to cover 100% of its annual electricity needs with their PV system. Which means that the systemSize_ you chose needs to cover the annual electricity consumption. You can perform EnergyPlus simulation or use any other way to get the annual electricity consumption.
Ladybug "Photovoltaics Performance" component can calculate the optimal systemSize_ by given the annual electricity consumption.However the component is made to address fixed tilt and azimuth PV systems only.An approximate way to overcome this is to calculate the optimal systemSize_ for fixed tilt and azimuth PV system, and then multiply it with the "difference in %s" panel at the very right of the fixed_vs_tracker_PV2.gh file. Again, this is not what Ladybug "Photovoltaics Performance" component is made to do, but it will probably get you in a ball park.
Inputted 32 degrees for north_ direction is actually 328 degrees.This is due to Ladybug Photovoltaics being based on NREL model which uses clockwise angles convention. This convention is also most commonly used in solar radiation analysis.
Dubai weather data files are uploaded in here.
…
he Cordyceps. Maybe some of you find this helpful/useful.
So basically, the Cordyceps is a physical module with 4 knobs and 1 slider. The knobs give an output between 1 and 1000, while the physical slider outputs 0-359. And of course, for this physical module I wrote a plugin to communicate with it. The knobs are intended to be the variables that modifies the design, while the physical slider is intended to be connected to the camera component.
Here I will put up "the recipe" for all to make their own module. You will be able to download the plugin as well.
Please send me a message if you want the 3D-files for the knobs, the box and slider knob. They've been made to directly 3D-print.
Plugin:
https://github.com/zakadjeb/Cordyceps/blob/master/Cordyceps/Cordyce...
Code for Arduino IDE:
https://github.com/zakadjeb/Cordyceps/blob/master/Arduino/_Arduino_...
What you need:
1x - Arduino (Leonardo, UNO or whatever)
4x - Potentiometers
1x - Sliding potentiometer
1x - Breadboard
Bundle of jump wires.
1. So, a potentiometer is a variable resistor, which is basically a component that changes the resistance between the voltage and the ground.
If A is supplied with 5V then B must be connected to Ground. The W will give "read" the resistance, and thus should be placed in Analog input (A0-A5) on the Arduino. The slider potentiometer works the same way.
2. Now connect the 4 pots to each their Analog input. The slider is supposed to be in A4. So to make sure:
A0: Knob1
A1: Knob2
A2: Knob3
A3: Knob4
A4: Slider
3. Now it's time to connect the voltage! Using the breadboard, the voltage can be sent through 1 line, the Ground as well. It should be quite easy to connect them.
4. Now, download the Arduino IDE and copy-paste the code I supplied above. In the IDE, you need to let it know which Arduino you're working with, and which port is should send the script.
5. Almost there. Download the plugin. Open the port you're using through the plugin. Set Start to True and the Cordyceps should be within you.
This recipe will be updated!
Let me know if there are any issues.
// Zakaria Djebbara…
he Cordyceps. Maybe some of you find this helpful/useful.
So basically, the Cordyceps is a physical module with 4 knobs and 1 slider. The knobs give an output between 1 and 1000, while the physical slider outputs 0-359. And of course, for this physical module I wrote a plugin to communicate with it. The knobs are intended to be the variables that modifies the design, while the physical slider is intended to be connected to the camera component.
Here I will put up "the recipe" for all to make their own module. You will be able to download the plugin as well.
Please send me a message if you want the 3D-files for the knobs, the box and slider knob. They've been made to directly 3D-print.
Plugin:
https://github.com/zakadjeb/Cordyceps/blob/master/Cordyceps/Cordyce...
Code for Arduino IDE:
https://github.com/zakadjeb/Cordyceps/blob/master/Arduino/_Arduino_...
What you need:
1x - Arduino (Leonardo, UNO or whatever)
4x - Potentiometers
1x - Sliding potentiometer
1x - Breadboard
Bundle of jump wires.
1. So, a potentiometer is a variable resistor, which is basically a component that changes the resistance between the voltage and the ground.
If A is supplied with 5V then B must be connected to Ground. The W will give "read" the resistance, and thus should be placed in Analog input (A0-A5) on the Arduino. The slider potentiometer works the same way.
2. Now connect the 4 pots to each their Analog input. The slider is supposed to be in A4. So to make sure:
A0: Knob1
A1: Knob2
A2: Knob3
A3: Knob4
A4: Slider
3. Now it's time to connect the voltage! Using the breadboard, the voltage can be sent through 1 line, the Ground as well. It should be quite easy to connect them.
4. Now, download the Arduino IDE and copy-paste the code I supplied above. In the IDE, you need to let it know which Arduino you're working with, and which port is should send the script.
5. Almost there. Download the plugin. Open the port you're using through the plugin. Set Start to True and the Cordyceps should be within you.
This recipe will be updated!
Let me know if there are any issues.
// Zakaria Djebbara…
ect + Geco
TUTORS:
Arturo Tedeschi (Authorized Rhino Trainer) + Maurizio Arturo Degni
Il workshop avanzato ECOLOGIC PATTERNS affronta l’impiego di strategie parametriche all’interno del processo progettuale, approfondendo l’utilizzo di Grasshopper in sinergia con plug-in, software di analisi ambientale e simulazione fisica. Obiettivo fondamentale è la generazione della forma come risultato di tecniche di form-finding e di input ambientali (solari, termici e acustici). Verranno acquisiti nuovi strumenti operativi e di simulazione al fine di costruire modelli parametrici ottimizzati in grado di adattarsi a diverse condizioni di contesto.
MORE INFO…
(1) I have been exporting small sections of a larger model into Maya from Rhino as FBX. In Maya I rotate and scale the models (-90 in X, Scale XYZ 0.001). The Named Views are being saved, but do not have a successful import into the Maya model. They do not appear as in Rhino, and the problem is not solved by scaling or rotating the cameras.
(2) If I try going the other direction, the cameras exported from Maya as FBX are also not aligning with the model in Rhino as they are in Maya.. I will do my best to post some images of the problem and hope you can help.
error !!
This is what the named views look like
here I am trying to the other way with a good view from Maya
strange placement..
This is the best result I can achieve, after I scale the camera by 1000
Any Advice???
Thanks, Robert.
…
ysim.ning.com/
When you run the simualtion you will notice on the batch terminal that Daysim is also being called, so you may want to consider how Daysim uses Radiance files & data.
Regarding your current problem, I think you stumbled onto something weird and interesting.
Interior and exterior readings appear to differ by 40 in the best case scenarios. Even setting the transmittance to 1 yields similar results. I tried changing from cummulative sky to climate sky and got similar values. Changing the test points did nothing either.
I think, (yet I'm too lazy to prove this) that the difference in values stems from diffuse radiation over the sky dome.
If you delete everything except the glass you'll notice that interior values are like 80-90% of the exterior values (this seems like the expected behaviour with a transmittance of 1). So, if we consider that a vertical window, part of an opaque box, is receiving radiation from 25% of a sphere, as you start to inset the interior test points the radiation they receive will be a fraction of the 25%.
Let me try to explain this better...The exterior surface receives radiation from a section of a sphere calculated by 180degrees on the xy plane (let’s call this angle theta) and by 90degrees (let’s call this angle phi) in azimuthal elevation. If you integrate this over spherical coordinates (theta from 0 to pi; phi from 0 to pi/2) you will find that it comes to a quarter of a sphere. By comparison, the interior surface will not integrate theta from 0 to 180degrees,nor phi from 0 to 90degrees, instead it will be the subtended angle from the exterior surface as a function of their separation; the farther in you go the smaller the view of the outside.
If my hypothesis is correct there shouldn't be that much difference since the separation is only 10cms...the subtended angle would be like 170 instead of 180 for theta and 85 instead of 90 for phi...overall if you integrate both spherical areas there should only by a difference of 10%.
In conclusion, I believe the unexpected behaviour stems from the previous subtended angle thing. If direct radiation was the only factor the difference would be the aforementioned 10%, which suggests that an additional source of energy is also affected by this. Perhaps indirect and diffuse radiation from other areas of the sky dome.
I’m definitely intrigued on why this is happening. Please post if you figure it out.
Regards,
Mauricio
…
TB of RAM. I think I'm going to start a GoFundMe campaign to buy one for myself :)
2- The server's cost is about $13 an hour. I get free access to supercomputer through my university and xsede.org because I earned an NSF Honorable mention last March, however, the supercomputers available through both resources are a little complicated for me to use, as opposed to the one available from amazon that has Microsoft server 2012 already installed.
3- I wanted to run 400 annual glare simulations for 400 different views.
4- I tried a to perform annual glare simulation for one view on my Dell XPS that has Intel Core i7-6700HQ processor and 16GB of system memory. The simulation took 2 hours to complete. Radiance parameter ab was set to 6.
5- I wanted to obtain the batch file for each view so I can run them on the server. So I used the fly component to run all 400 simulations and closed the cmd windows, that wasn't bad ( for me at least) because I asked my son to this job for me, he was just glad to help me :)
6- I created one batch file using this cmd command:
dir /s /b *.bat > runall.bat
This created a file with the path to each .bat file. I edited this file in Notepad++ to include the word "start" at the beginning of each line. This was done using the "find and replace" dialogue box.
7- I split my newly created batch file into 3 batch files, each one has about 130 file names and " start" before the file names.
8- installed radiance on my server
9- Ran the first batch file on the server, this started 130 cmd windows performing my simulations, CPU usage was anywhere between 90% to 100% and about 105 GB of RAMs were used.
10. It took about 5 hours to complete all 130 simulations, I expected to run all in 2 hours but can't complain because this would've taken about 260 hours to run on my laptop. After the simulations done I ran the second and then the third batch files ( total of about 15 hours).
11. I got 400 valid dgb files. Couldn't be happier!
…
he time to work with it.
the project is about facade strips which turns along height. the top angle is
parallel to the facade and the bottom is max. 90 degrees twisted, but the strips
should turn diffrently to achieve more dinamic look.
first i have tried to achieve this by calculating distance between the rotation angle from points of the grid and a single point.
then i have tried to ad some more effecting points and used the distance to the divided surface (the circles are just to control the area of effection):
i manually lofted it.
the result is a bit annoying becouse the points that effect the angle are always visible:
i have triend to solve this by drawing a line and divided it to recieve points along the bottom of the geometry. the result is not working properly:
Anyway,
there must be a better/smoother way to achieve this. i would like to effect the twist of the surfaces by distance to a spline, but im just lost. can you help me please?
the problems im encountering:
0- distance spline to grid to effect the angle
1- list of x/y coordinates and angle of rotation for each point of the grid
2- export points to excel
3- lofting lines in one direction only (x1, x2, x3...)
4- reduce the list data to 2 decimal (0,00)
5- maybe angle from radian to degrees
thx…
ort and export from the images below and also from the HELP file of DB in attachments (Page 71: Importing Geometric Data; Page 78-80: Import 3 - D CAD Data). In their HELP file, they mention about "import geometric data".
However, regarding the input of schedules, loads, constructions and etc., DB normally uses "Component " and "Template" (Page 29: Templates And Components; Page 591: Templates; Page 533: Components). "Templates" are databases of typical generic data, including Activity templates, Construction templates, Glazing templates, Facade templates, HVAC templates, Location Templates, and etc. "Component " are databases of individual data items (e.g. a construction type, material, window pane).
Both "Component " and "Template" are allowed to be imported and exported by using "Import / Export library data" command (.ddf format - DB Database File; Page 734: Import Components/Templates, Export Components/Templates). DB also allows us to build up our own libraries of templates and components (Page 731: Library Management; Page 733: Template Library Management).
In order to import both geometric information and other information related to schedules, loads, constructions and etc. from GH to BD, we supposed the following two ways:
1. GH(HB+GB) --> gbXML (both geometric and "Component " and "Template" information) --> DB
This is the way we most prefer. We did see information related to schedules, loads, constructions encoded in the gbXML file generated by GB, but still do not know the reason why DB did not take this information (I also mentioned this in Q6 within the gh file). We assume this might because the gbXML file we create encodes the schedules based on a different template / schema than the one DB expects. We also post this question to the DB forum for help.
(http://www.designbuilder.co.uk/component/option,com_forum/Itemid,25/page,viewtopic/p,13755/#13755)
2. GH(HB+GB) --> gbXML (geometric information only) + .ddf ("Component " and "Template" information only) --> DB
If the first way doesn't work and DB only takes geometric information from the gbXML, then we might think of the other way - generating the .ddf files from GH(HB+GB) to pass the schedule, load and construction information to DB.
I was wondering if it is feasible for HB and GB to have this function? And what is your suggestion to achieve this?
In addition, we notice that DB can export XML files (not gbXML), so we are trying to figure out if DB also accepts / reads the XML file. If so, we might be able to convert the gbXML (with both geometric and schedule information) to XML. What do you think about that?
Thank you again for all your help!
Best,
Ding
DB import
DB export
Template libraries
Component libraries
…
Introduzione a Grasshopper", il primo manuale su Grasshopper.
.
I corsi PLUG IT nascono dalla volontà di promuovere le nuove tecnologie digitali di supporto alla progettazione e condividere il know-how maturato attraverso ricerca, collaborazione con i più importanti studi di architettura e pubblicazioni internazionali.
.
Verranno introdotte le nozioni base di Grasshopper approfondendo le metodologie della progettazione parametrica e le tecniche di modellazione algoritmica per la generazione di forme complesse. Il corso è rivolto a studenti e professionisti con esperienza minima nella modellazione 3D e si articolerà in lezioni teoriche ed esercitazioni.
. Argomenti trattati:
- Introduzione alla progettazione parametrica: teoria, esempi, casi studio - Grasshopper: concetti base, logica algoritmica, interfaccia grafica - Nozioni fondamentali: componenti, connessioni, data flow
- Funzioni matematiche e logiche, serie, gestione dei dati - Analisi e definizione di curve e superfici
- Definizione di griglie e pattern complessi - Trasformazioni geometriche, paneling - Attrattori, image sampler
- Data tree: gestione di dati complessi - Digital fabrication: teoria ed esempi - Nesting: scomposizione di oggetti tridimensionali in sezioni piane per macchine CNC
.
Verrà rilasciato un attestato finale.
.
Ulteriori info e programma completo su: www.arturotedeschi.com e su www.edizionilepenseur.it…