ase to give the same result using a graph mapper with a parabola as in the attached file
Unfortunately it never gave the same result ..... is it a mistake in the book ?!…
moved by random amounts in a random direction. The animated slider was the amount of deviation from the original points. And yes, I used culled lists.B.t.w. did you find my workaround for your loft? Did your notebook explode? ;)…
0.533000void brightfunc skyfunc2 skybright perezlum.cal010 1.382e+00 3.201e-01 1.066879 -0.754821 0.015485 -0.048998 -0.089403 0.066341 -0.860010 0.505947
The values in bold are then evaluated using the equations in the file perezlum.cal inside the RAYPATH directory in Radiance..
{ All-weather Angular Sky Luminance Distribution . Additional arguments required for calculation of skybright: A1 - diffus normalization A2 - ground brightness A3,A4,A5,A6,A7 - coefficients for the Perez model A8,A9,A10 - sun direction}skybright = wmean((Dz+1.01)^10, intersky, (Dz+1.01)^-10, A2 );wmean(a, x, b, y) = (a*x+b*y)/(a+b);intersky = if( (Dz-0.01), A1 * (1 + A3*Exp(A4/Dz) ) * ( 1 + A5*Exp(A6*gamma) + A7*cos(gamma)*cos(gamma) ), A1 * (1 + A3*Exp(A4/0.01) ) * ( 1 + A5*Exp(A6*gamma) + A7*cos(gamma)*cos(gamma) ) );
This data is then mapped to the "glow" material that represents the celestial hemisphere...You can edit the climate based sky produced by Honeybee and enter your own values. The other option would be to just use gendaylit from DOS Prompt.…
closest point to the very first would be removed from the list, so the initial list reduces from 100 to 98. From the 98 i pick one and search the remaining 97 for the closest. From the remaining 96 i pick again one and search in the 95,...
(The product I want to result is:
having a number of random lines in 3D space, produced by an even number of points as discribed, this shall be the initial springs for a ("selfadjusting") tensegrity. Each one of these lines (later springs in kangaroo) get divided in three areas - that means four points. These four points again are the "attractor points" of neighbor springs, so the strut "knows" where to set the next elastic connection,...the rest I´ll have to figure out)
angelos…
a working solution with replacing this line of code with:
Dim charList As New List(Of Char)(charArr)
Is this because of a version incompatibility (I'm using Rhino 4.0, and GH 0.8.0062)? Just curious.
Regards,
JJ…
f the mesh was self-intersecting everywhere. So instead I used Millipede (isosurface) to get the same undulations, but ignore the complex 'folds', you can see the difference in cross section thickness. I then tessellated it with the inverse pattern of the outer surface.
To make it a single 3d printable mesh, i just deleted a single face on inner and outer skin, then lofted the naked edges. (creating a tiny hole through the model). Therefore creating a single mesh that folds in on itself, not sure if there is a better way of defining the space between two meshes as the solid area...
Full GH (Kangaroo - Meshmachine - Weaverbird - Millipede)
Special thanks to Laurent Delrieu for his interesting offset mesh method that i based my approach on.
http://www.grasshopper3d.com/forum/topics/offset-mesh-problems-with-3d-mesh-with-weaverbird…
Added by Nick Tyrer at 5:25am on December 10, 2015
g these times itself). If it works on selection alone, it would probably implement faster.
Theoretically, does this mean the total solving time of the definition is the 'chain of components' that takes the longest time? In the picture above, it would be the chain consisting 'point-curve-divideDistance'?
Because that still adds up only to 97%, I am assuming the Point and Slider component start solving in parallel, and the two Divide components also start solving in parallel?…