orders from bottom to top. There are three pre-set heights: 20,000 / 50,000 / 80,000 (or 20, 50, 80 meters, I'm working in mm).
So if the three cantilevering volumes would be numbered 0,1 and 2, then I'm looking for a way to let Grasshopper generate the following:
A = 20m-position
B = 50m-position
C = 80m-position
(A,B,C):
0,1,2
0,2,1
1,0,2
1,2,0
2,0,1
2,1,0
Attached is wat I have so far, I have only managed to make simple translations per geometry.
…
summer because of the relative humidity of outdoor air will be over 80%.
I want to set the schedule like this
1) cooling setpoint to be 27C degree and max humidity to be 50%.
2) when the outdoor air temperature is lower than 27C, open the windows and ventilation naturally.
3) Air conditioning and dehumidification are needed only when the occupancies are at home (almost at night) and Natural ventilation is not to be.
4) Accept the indoor air relative humidity to be almost 100% when dry bulb temperature is lower than 27C.
Now, I set the air conditioning schedule as cooling setpoint schedule, but there are no components to set a dehumidification setpoint schedule.
The dehumidifier keeps working all day whichever the windows are opening or not.
How can I stop the dehumidifier during the windows open?
thank you.…
perienced with grasshopper, but so far I've managed to combine the following:
Giulio Piacentino's "Catenary arch from height" script
Pirouz Nourian's "Mobius" script (Obtained from a friend)
End Result:
Here's where I'm stuck: I want the mobius twist to revolve around the midpoint of the arch, but the script uses the input values to determine the endpoints, resulting in a weird sinuous shape when viewed from above. Also, the secondary end points (generated by the mobius script, determining the width of the surface) are generated by default along the z axis, resulting in an arch that only touches the "ground" at two points. I attempted to work around this issue by trying to force the zHeight parameter to correspond with the y axis (thus rotating the arch 90 degrees so it would lay "flat"), but the script interprets the third point as a value and not as an actual point to bisect. I thought this might be an issue with the C# component that I obtained from Giulio Piacentino's script, so I attempted to tinker around with the source code. Unfortunately, I'm not fluent in C# so I only managed to mess everything up (I've since recovered the code from the cache). Anybody got some ideas? -BC …
ng (It's a bit similar to the Knapsack problem):
I have a Variable --> XandI Have fix numbers (can we call "pieces") 9,12,15,18
I'd like to reach the X, with the summing of these numbers and using the minimum pieces ,it can't be lower than X, but it can be higher, maximum with 3.After this it has to found the most optimal combination which mostly use the same pieces
E.G.
X=98
The wrong solution is like = 1pcs of 18 = 9pcs of 9
Sum of pieces are 10
OR
= 3pcs of 18 = 1pcs of 15 = 1pcs of 12 = 2pcs of 9
Sum of pieces are 7
The right solution in this case = 5pcs of 18 = 1pcs of 9
(5*18)+(1*9)=99 it's good beacuse it's over with maximum 3 and uses the minimum pieces
Then it sends to a list like18 : 5pcs15 : 0pcs12 : 0pcs9 : 1pcsCan somebody help me ? Or is it possible to make this ?
Thank you…
Added by Petrik Kollár at 1:09am on November 10, 2017
llowing for higher skyline and construction areas along public transportation corridors. Up until now, neighborhoods once characterized by two-story houses, gardens and ground- floor open shopfront programs, have been completely transformed by the introduction of fortressed monolithic residential and office towers, which lack any sort of urban street life.
The new master-plan, however, now requires buildings to have an open street façade to accommodate multiple programs. Led by tutors from UNStudio (www.unstudio.com), the AA Visiting School São Paulo will address the changes being prescribed by the new masterplan through the redefinition of the tower typology in the extending of the ground of street culture, green landscapes and ecological mediation along the vertical axis of these buildings. For this, the workshop will teach advanced digital design and fabrication techniques to explore a series of novel differentiating structural and environmental organizations in the redefinition of the São Paulo skyscraper.
For more information:
saopaulo.aaschool.ac.uk
Applications:
https://www.aaschool.ac.uk/STUDY/ONLINEAPPLICATION/visitingApplication.php?schoolID=303
For any queries, please email: brazilvisitingschool@aaschool.ac.uk.…
llowing for higher skyline and construction areas along public transportation corridors. Up until now, neighborhoods once characterized by two-story houses, gardens and ground- floor open shopfront programs, have been completely transformed by the introduction of fortressed monolithic residential and office towers, which lack any sort of urban street life.
The new master-plan, however, now requires buildings to have an open street façade to accommodate multiple programs. Led by tutors from UNStudio (www.unstudio.com), the AA Visiting School São Paulo will address the changes being prescribed by the new masterplan through the redefinition of the tower typology in the extending of the ground of street culture, green landscapes and ecological mediation along the vertical axis of these buildings. For this, the workshop will teach advanced digital design and fabrication techniques to explore a series of novel differentiating structural and environmental organizations in the redefinition of the São Paulo skyscraper.
For more information:
saopaulo.aaschool.ac.uk
Applications:
https://www.aaschool.ac.uk/STUDY/ONLINEAPPLICATION/visitingApplication.php?schoolID=303
For any queries, please email: brazilvisitingschool@aaschool.ac.uk.…
s levels of detail by subdividing a 6 sided cube mesh and projecting its vertices according to a referenced height map. This is one of the standard conventions for building full sizes planets. At the lowest level (0) the mesh planet is made of 6 pieces(each 32x32 resolution). The next level down (1) is made of 24 pieces... 6 divided by 4 = 24. Level (2) is 96 quads etc etc. The script will generate each quad at its sub-division level and compare edge vertices to neighboring quads. It will then make sure any shared vertices are in fact at the same projected vector. This ensures a planet quad with edge vertices that match.
The problems comes in texturing each quad.
If I build the quad as a nurb surface from points I can place the texture easily because each surface UV maps squarely to my texture map (which is also square).
If I build the quad as a mesh I cannot just apply the square texture to the mesh UVs. This is because when you unwrap the UVs from a mesh they will not unwrap like a nurb surface's UVs. Therefore to get the correct mapping I would have to manipulate each UV back to an evenly aligned array (which is 1024 points in a 32x32 resolution UV). Maya and blender have 'relax uv' and 'align UV' functions but they don't do the trick and manual corrections are out of the question. So why not skip the mesh method and use the nurb method?
I did this and there is a trade off. The nurb will accept the material texture I want with no other work on my end but when I export the object as an .obj rhino creates its own mesh to describe the nurb(with various unsatisfactory setting options). This works great up to a point because at some level the interpreted mesh will have vertices that do no match at the edges, ie .. creating visible seams in the mesh. The picture below is the nearly seamless planet at LOD(1) made of 24 quads, each with 32x32 vertice resolution and a 512x512 jpg texture running in Unity3d 5. It works but at close level there are seams. This will be resolved simply by having the next LOD(x) instantiate before getting close enough to see the seam but at core nerd level I want the seamless mesh.
So, I can make the seamless mesh but I can not realistically texture map it. I can also make the nurb surface from points and texture it at the expense of the edge vertices matching. I am at the split in the road but I want to have my cake and eat it too. Thoughts, comments, trolls...?
Thanks for reading =)
Footnote: For you pros I am not using seamless noise across the map I am using grasshopper to sew up my otherwise non perfect edges.
Other programs in the pipeline:
-WorldMachine 2
-Wilbur
-Photoshop
-Unity3d…
angel but when it comes to material behavior, stresses, surface tension i think that "our" tools are still no complex and powerful enough - and like i said i didn't really see the benefit in the work of my friend form the digital experiment.
so i think the question is is there a benefit from your digital experiment or do you rather stick to the physical experiment.
…
of 400 interlocked rings in a 20 X 20 grid.
V1 - A single 'suLoop' component doing 400 'SUnion' operations (20 X 20): 11.6 minutes
V2 - Two phases: 5 X 10 in phase one and 2 X 4 in phase 2, 58 'SUnions' total: ~88 seconds combined
V3 - Two phases: 4 X 5 in phase one and 4 X 5 in phase 2, 40 'SUnions' total: ~104 seconds combined
Again, these Profiler benchmarks don't reflect the whole picture, and might be affected by other things I was doing on the laptop while the code was running.…
Added by Joseph Oster at 12:29pm on March 23, 2017
,
and then I saw under Application that resources are managed by 'Icon and manifest'.
That can also be set as 'Resource file', but then a file path is required.
Is 'Icon and manifest' OK, or have I to set thing differently ?
Also, in the class code I inserted the following:
( I saw it mentioned here in the forum )
protected override Bitmap Icon { get { return Resources.colour; } }
( colour.png is the image file's name )
but VS gives me an error, saying:
Error 1 The name 'Resources' does not exist in the current context C:\Program Files\Rhinoceros 5 Evaluation\gh\plug-ins\ColourRhOb\Class1.cs 88 26 ColourRhOb
Did I miss a reference in the code ? Here they are:
using System;using System.Drawing;using System.Collections.Generic;using Grasshopper.Kernel;using Grasshopper.Kernel.Types;using Rhino;using Rhino.DocObjects;using Rhino.Geometry;
What am I doing wrong ?
Thanks
emilio
…