, and made the below definition to try it out. (lots of components to draw a line, but I'm just trying to understand the equation)
I had been searching for advice on some geometry topics worth exploring for a class, and now I'm in the class and the teacher wants me to start by learning about splines in general (not nurbs). I just spent the day learning linear spline interpolation, then quadratic, then cubic. I didn't try working them by hand yet, but I'm getting the concepts. It seems cubic is the lowest degree where you can get C2 continuity, which makes it smooth. I read over parameterization and how that simplifies the number of equations. I read about space curves, and then the differences between Hermite, Catmull-Rom, and Cardinal spline, but then got tired and had a cocktail.
So I guess I'm looking for any direction or advice on how to understand parametric curves in 3d space, and how they can be defined (splines or otherwise). Thanks!!!
…
nts but as there are polylines and surfaces in it, they are conflicting as the geometries are overlapping and intersecting.
The input for the model is a centre point and four connecting points: we can call them CNT, A, B, C and D. The model works for these points - it's quite complicated with lots of polylines, vector geometry, surfaces, rotations, etc. - but it still works and has an output of two breps.
If I had a compilation of N sets of CNT, A, B, C and D's, is there a way of feeding each of these into the grasshopper in individual sets rather than just plugging in the huge set of numbers - e.g. feeding in CNT1, A1, B1, C1 and D1 and getting a result before moving on to CNT2, A2, B2, C2 and D2?
I've tried looking through tree structures, but it seems to be failing when the size of the set isn't known - e.g. how to extract all the information from trees when N isn't know using list item (i=0, i=1, i=2..., i=N).
I hope I've managed to explain the problem adequately, I can make up an easier to understand Grasshopper model later if I haven't explained well...
Thanks in advance for any comments, pointers, etc.…
orm of the model but when I try to add the piping to it, I get the message saying Windows has ran out of memory.
I am using Windows 7 and have tried going into the BCD as recommended here: http://wiki.mcneel.com/rhino/memoryincrease but I was not able to run this command.
I have then tried to increase my virtual memory within Windows, even up to 30GB with no luck.
I'm pretty sure I'm doing something really wrong here but I really need to get this modelled ASAP for a portfolio submission.
Any help would be very much appreciated!
Regards
James
…
erencing it back into our main .gh file works normally (with full functionality) as long as all the files are on my local hard drive (e.g. "C:"). But as soon as I try to reference a .ghcluster or even open one saved on an external drive (our company's network drive) Rhino and Grasshopper instantly freeze und crash. Every time. No matter the file size.
We have already checked, if maybe whitespaces or dots in the file's path could have caused the crashes. But even eliminating them by renaming the folders doesn't fix the problem.
So obviously GH's clusters does not support referencing files from external network locations. Does anyone have an idea why? Were stuck here, because we want to severely increase the complexity of our project's main gh. file and enable more team members to contribute to the main file via external referenced cluster files.
Thanks for your help.
BB…
greatly appreciate it!!
You can write the number of the question and write your answer next to it, example:
1) a
2) c
3) a) Washington University in St. Louis
4) 2 weeks (1week+1week shipping)
5) 130
6) b
7) b
The survey questions are as follows:
1)
Did you 3D print before?
5)
How much did it cost (in dollars)?
a.
Yes, for a school project
a.
Between 20 & 50
b.
Yes, for a personal project
b.
Between 50 & 80
c.
Between 80 & 120
2)
Print size
d.
Please specify if otherwise: _____ dollars
a.
Between 2 & 6 cubic inches
b.
Between 6 & 12 cubic inches
6)
Do you think the price was expensive?
c.
Between 12 & 20 cubic inches
a.
Not at all
d.
Please specify if otherwise: ____cubic inches
b.
A little bit expensive
c.
Very expensive
3)
Where did you print your object?
a.
School
7)
Were you satisfied with the printed object?
b.
Outside school: _________________
a.
Yes, it was a great print without problems
b.
Not bad, some issues
4)
How long did it take to print?
c.
I was not satisfied, very bad quality
a.
___ days
b.
___ weeks
Thank you very much to all!!
PS: If you did many 3D prints, you can post multiple answers.
Wassef…
ceros.
Public concerné /
Architectes et designers, utilisateurs de Rhino souhaitant paramétrer Rhinocéros à l’aide de Grasshopper, programme
associant des composants et une structure de graphe interagissants avec le modèle Rhino.
Une bonne connaissance de Rhinocéros est nécessaire. La langue de la formation est le français.
Structure et Objectif de la formation /
La formation se déroule sur 3 jours : les 2 premières journées sont consacrées aux « fondamentaux » de Grasshopper
avec en préambule une introduction au design et à l’architecture paramétrique et leurs impacts dans la conception, la
création et la construction.
La troisième journée sous forme d’atelier est dédiée à l’étude de cas concrets proposés par les stagiaires, qui, quelques
jours avant la formation, pourront envoyer leurs projets par mail à info AT rhinoforyou DOT com
Les stagiaires, après la formation, pourront rester en contact avec les formateurs de HDA par le biais du blog
complexitys.com et le twitter @HDA_Paris. La durée de cette formation permettra d’atteindre une autonomie et une
bonne compréhension basée sur des exemples concrets.
3 Formules possibles /
3 jours ( Initiation+Atelier ) : du lundi 20 septembre au mercredi 22 septembre
2 jours ( Initiation ) : lundi 20 et mardi 21 septembre
1 jour ( Atelier ) : mercredi 22 septembre
Programme ind icatif des notions traitéES pendan t la formation /
Introduction à la conception Paramétrique . Rhinoscript, Grasshopper: différences et similarités . Interface
graphique de Grasshopper . Objets, Données, Listes . Opérateurs scalaires : La mathématique de
Grasshopper . Gestions des données : la logique de Grasshopper . Vecteurs, Points, Lignes, Surfaces : La
géométrie de Grasshopper . Listes, Arbres, Branches . Le dessin paramétrique: exercices divers et exemples
. Références, Bibliographie, Support de cours . Ateliers d’architecture et design paramétrique (3ème jour) .
Moda lité de la formation /
Venir avec un PC portable équipé de Rhinocéros version 4.0 SR 7 et de la dernière version du plug-in
Grasshopper (téléchargeable sur www.grasshopper3d.com).
Le coût du stage est de 350 € HT/jour par personne.
Réserver votre place dès que possible car les places sont limitées à 10 participants maximum.
Inscriptions et renseignements: Jacques Hababou, info AT rhinoforyou DOT com
Pour en savoir plus sur l’architecture paramétrique: www.complexitys.com…
troducción a su plugin de modelado paramétrico, Grasshopper.
Con este tipo de herramientas podemos pensar formas más allá de las cajas para diseñar, porque seremos capaces controlar con total rigor geometrías muy complejas.
En el siguiente video, podemos ver un ejemplo realizado durante un curso impartido anteriormente en Madrid por el profesor, Francisco Tabanera, en el que se realiza una interpretación del proyecto de BIG para la Biblioteca Nacional de Kazajstán.
<a title="Interpretación de la Biblioteca Naiconal de Kazakstan, de BIG" href="http://www.youtube.com/watch?v=YLldO-SxgPw" target="_blank"></a>
A lo largo del curso se realizarán diferentes ejemplos que podrán ser realizados por todos los asistentes, ya que no es necesario ningún conocimiento previo para su seguimiento.
El curso se desarrollará en las oficinas de Arquitecton en Barcelona con el siguiente horario:
HORARIO
Sábado 1 de Marzo
De 9.30 a 13.30h.
Sábado 1 de Marzo
De 15.30 a 19.30h.
El curso está planteado para un máximo de 9 alumnos, para conseguir el máximo aprovechamiento posible por parte de los mismos.
El curso tiene un precio de 90€. Estudiantes y desempleados tienen un descuento del 10%. Es posible asegurarte una plaza con un primer pago de 25€ a modo de reserva.
Apúntate aquí…
whole design intent, but this is what Inventor is good at. The way it packages bits of 'scripted' components into 'little models' that can be stored and re-assembled is central to MCAD working.
The Inventor model shown is almost 5 years old. We don't model like that any more, however it does offer a good idea of general MCAD modeling approaches.
iParts is useful in certain situations, it could've been useful in the above model, its usefulness is often in function of the quantity of variants/configurations.
So much is scripted in GH, maybe it should also be possible to script/define/constrain/assist the placement/gluing of the results?
...
Starting point: I think we are talking across purposes. AFAIK, the solving sequence of GH's scripted components is fixed. It won't do circular dependencies... without a fight. The inter-component dependencies not 'managed' like constraints solvers do for MCAD apps.
Components and assemblies are individual files in MCAD.
Placement of these within assemblies in MCAD is a product of matrix transforms and persistent constraints. There is no bi-directional link, the link is unidirectional (downflow only), because of the use of proxies.
Consequently, scripting the placement of components is irrelevant in GH, unless you decide that each component needs to be contained in its own separate file.
This also brings up the point that generating components and assemblies in MCAD is not as straightforward. In iParts and iAssemblies, each configuration needs to be generated as a "child" (the individual file needs to be created for each child) before those children can be used elsewhere.
You notice the dilemma, if you generate 100 parts, and then you realize you only need 20, you've created 80 extra parts which you have no need for, thus generating wasteful data that may cause file management issues later on.
GH remains in a transient world, and when you decide to bake geometry (if you need to at all), you can do that in one Rhino file, and save it as the state of the design at that given moment. Very convenient for design, though unacceptable for most non-digital manufacturing methods, which greatly limits Rhino's use for manufacturing unless you combine it with an MCAD app.
One of the reasons why the distributed file approach makes perfect sense in MCAD, is that in industry you deal with a finite set of objects. Generative tools are usually not a requirement. Most mechanical engineers, product engineers and machinists would never have any use for that.
The other thing that MCAD apps like Inventor have, is the 'structured' interface that offers up all that setting out information like the coordinate systems, work planes, parameters etc in a concise fashion in the 'history tree'. This will translate into user speed. GH's canvas is a bit more freeform. I suppose the info is all there and linked, so a bit of re-jigging is easy. Also, see how T-Flex can even embed sliders and other parameter input boxes into the model itself. Pretty handy/fast to understand, which also means more speed.
True. As long as you keep the browser pane/specification tree organized and easy to query.
:)
Would love to understand what you did by sketching.
I'll start by showing what was done years ago in the Inventor model, and then share with you what I did in GH, but in another post.
Let's use one of the beams as an example:
We can isolate this component for clarity.
Notice that I've highlighted the sectional sketch with dimensions, and the point of reference, which is in relation to the CL of the column which the beam bears on. The orientation and location of the beam is already set by underlying geometry.
Here's a perspective view of the same:
The extent of the beam was also driven by reference geometry, 2 planes offset from the beam's XY plane, driven by parameters from another underlying file which serves as a parameter container:
Reference axes and points are present for all other components, here are some of them:
It starts getting cluttered if you see the reference planes as well:
Is I mentioned earlier, over time we've found better ways to define and associate geometry, parameters, manage design change, improving the efficiency of parametric models. But this model is a fair representation of a basic modeling approach, and since an Inventor-GH comparison is like comparing apples and oranges anyways, this model can be used to understand the differences and similarities, for those interested.
I haven't even gotten to your latest post yet, I will eventually.…
Added by Santiago Diaz at 10:36am on February 26, 2011
he picture (4).
Previously, I had a problem with generating intersections between the two directions of the beams, but a colleague helped me by extending beams, so there was no problem with lines of intersection. But this solution has generated curl (5) at the highest vertex geometry, which I ignored in order to repair it before printing, perhaps this mean my problem with my beam spread properly. Only when the beams is 19, does not jump no problem, but I still can not distribute them properly.
(1)
(2)
(3)
(4)
(5)
I tried to show as simply as possible by removing or signing my code in GHX file.
Thank you in advance for your help
…