lts.
In the visualization, points is an interesting option. It's a matter of aesthetics I guess, I go with surfaces :) Also what you can try is selecting Filters -> Slice (you can also find it in the icons above the pipeline viewer), in the Slice options below the pipeline press Z normal and on the Z coordinate press some height relevant to the buildings (e.g. 1.75m a typical human scale). That would show you the flow around the buildings on that height. Experiment with selecting other normals and values. Keep playing with the filters there's some cool things in there. Also you can check out the mailing list and extensive paraview documentation.
Concerning the errors I apologize because I just downloaded your case.
It appears that the decomposeParDict is not included in the system folder. I am not sure if this is due to BF not going through the whole workflow yet or an ommission on our side. Please feel free to add it in Github. I will also note it down and pass it to Mostaph to check. In the meantime please find attached a VERY detailed decomposeParDict file. I took the liberty to set it at 4 processors (the numberOfSubDomains value) and also selected (that is uncommented) the scotch decomposition method. It's the easiest method to use since it is automatic and doesn't require any more inputs on how the domain is decomposed on the x,y,z directions (which would require you to change values in the attached file).
Now, the different folders created are simply snapshots of the current solution at the specific timestep. To control how often the solver is saving change the writeInterval number in the controlDict file. You can also change almost all these values on the fly, while OF is running.
Finally, concerning the other errors of parafoam it seems somehow parafoam is reading the intial condition names instead of actual results from the solution files and it doesn't like it.
Does this happen only when you open the case (i.e. at 0 time) or does it also happen when you move to an other timestep?
Also, are you using paraFoam, paraview or the paraFoam -builtin method?
The extension of the paraFoam file seems to be .foam which means you are probably using the built in viewer. That might be the issue but I'm not sure.
Can you try running paraview, navigate to your case folder, open the .foam file and see if there is still an error?
Also, if it isn't much trouble can you zip one of the time folders and attach it here? I'd like to take a look at what's inside to check against what the error report says.
Once again thanks for testing!
Kind regards,
Theodore.…
rce of power.
A fortified emplacement for heavy guns.
Synonyms
accumulator
And use component:
com·po·nent
/kəmˈpōnənt/
Noun
A part or element of a larger whole, esp. a part of a machine or vehicle.
Adjective
Constituting part of a larger whole; constituent.
Synonyms
noun.
constituent - element - ingredient - part
adjective.
constituent - constitutive
…
n to finding a concave contour polyline (which is in general what you need). In your case each contour section contains a series of points of which you do not know the order and you need to sort them so that by connecting them you find the contour. This is fairly easy to do when the contour is convex (basically you find the average point then calculate the vectors from the average to the points and sort the vectors by angle - sorting the points by the same angle gives you the right order for the contour), but generally impossible to find uniquely when the contour is concave (PS: convex means that, for ANY 2 points inside the figure, a straight line connecting them doesn't intersect with the border curve - i.e. circles, ellipses, rectangles, triangles - concave shapes are a star, a crescent moon, an arrow, a boomerang, etc.).
The problem goes like this: given a generic list of points:
Each of these configurations for a perimeter equally fits the above:
Laurent already went for another possible solution, the stochastic approach (by subdividing the connecting lines), I slightly adjusted a few things over his solution:
namely, I added a rounding option to adjust for some weird tolerance issues (some points that should be at Y=80 were at Y=79.99998 or something) and a more straightforward solution to group them by section plane using sets logic. This, coupled with alpha shape, gives a quite good approach, still very coarse in terms of results but that depends on the sampling resolution of the field (i.e. number of height sections in which you calculate the metaballs) and sampling length of the connecting lines.
Definition attached.…
Diffraction , I left it, how it is.
For the unusual issues that comes in the image source component, so, is it something strange? But, I still have the same issues when I sets any integer component (single or multiple) in the “reflection order” of the image source component, in the “image source order” in the ray tracing component, and again, when I connect the output “Direct sound data” of Direct Sound component in the Energy Time Curve.
Do I wrong something with the integer component? I used it already in the first parts, for sets “grasshopper layers”, in the “Scene” component, but here it works. Should I start with a new file?
For the multi-object optimization, thank you for all suggestions. Yes, I red PHD thesis work of Tomas Mendez and the article “ EDT, C80 and G Driven Auditorium design” and still others. Thank you to all these articles, I decided where to focus my thesis.
I understand the potential of Multi-object optimization, and problems that I can finding without using it. Actually, in the beginning of my thesis, I tried to jet in contact with the Politecnico di Torino, but was not easy because I’m not a Politecnico student.
Here, in University of Florence (Building engineering), there isn’t a department or someone that is already familiar with these field of study, so, as you can image, for design my thesis, I can confide on online resources. So far, my Professor suggest me to begin with a Nonlinear Global optimization like Galapagos, and only after see the multi-object. In this way, step by step if something doesn’t work is easier to understand way and where something is going wrong: if are problems due to the setting of the programs, because we are not practical about these, or if there is a wrong in the simulations or in the algorithm and ect.
Do you think is a good way for go on?
Thank you very much,
Kind Regards
Giulia
…
connected hyperspace where architecture can be fluid, flexible and vivid, yet the aspect of materiality requires more attention.
Action-designed structures begin to move beyond the utopian proposals of the 20th century’s manifestos and hold a place in the world of realized designs. The AA Athens Visiting School aims to bring users closer to the built environment while revisiting habits of designing, building and experiencing space through materiality. Understanding materiality and form as a ‘unified whole’, the programme integrates manufacturing techniques through the experimentation fabrication of prototypes at a 1:1 scale.
Prominent Features of the workshop/ skills developed
Participants become part of an active learning environment where the large tutor to student ratio allows for personalized tutorials and debates.
The toolset of the Athens VS includes but is not limited to Processing and Grasshopper for Rhinoceros, as well as design analysis software.
Participants gain hands-on experience on digital fabrication.
Design seminars and a series of lectures support the key objectives of the programme, disseminating fundamental computational techniques, relevant critical thinking, theoretical understanding and professional awareness.
Applications
1) You can make an application by completing the online application found under ‘Links and Downloads’ on the AA Visiting School page. If you are not able to make an online application, email visitingschool@aaschool.ac.uk for instructions to pay by bank transfer. 2) Once you complete the online application and make a full payment, you are registered to the programme. A CV or a portfolio is NOT required.
The deadline for applications is 28 June.
Location AKTO College – Athens Campus 11Α Evelpidon Street (Pedion Areos) Athens, 113 62, Greece
Fees
The AA Visiting School requires a fee of £695 per participant, which includes a £60 Visiting membership fee. Fees do not include flights or accommodation, but accommodation options can be advised.
Eligibility The workshop is open to current Undergrad and Graduate architecture and design students, PhD candidates and young professionals. Software Requirements: Adobe Creative Suite, Rhino 5.
For more information, please visit:
http://www.aaschool.ac.uk/STUDY/VISITING/athens
http://ai.aaschool.ac.uk/athens/
For inquiries, please contact:
alexandros.kallegias@aaschool.ac.uk…
ails.
Some word about the mesh... (see Image_01)
I took a flat 4 points NURBS surface as imput (very easy, it defines the total area of my pavilion) and some points (that defines the contact with the ground).
Then I extracted a grid of points from the NURBS (Surface_Util_Divide surface) and compared 'em with the contol points, in order to associate to each grid's point its own attractor (Vector_Point_Closest Point).
Than I moved the points down. I used the distance from each point to its attractor (inverted) as amplitude for the vector of the movement, in order to say: the nearer you are to the control point, the more intense your movement will be. During this operation I've passed the distances' data list into a graph mapper (Params_Special_Graph Mapper), in order to regulate in a very intuitive and interactive way the shaping of my canopy.
At the end of the process I asked GH for a simple Delaunay mesh (Mesh_Triangulation_Delaunay Mesh). It's a very cool command, I believe!!!
Ok, now some word about the component, it's design and it's repetition/adaptation to the mesh...
(see Image_02)
I took the mesh and extracted components on first and faces's information on second. Then I selected and separated the vertexes (1°, 2°, 3°) of each triangular face into threee well defined list.
Then I re-created the triangles' edges. Please pay attention because it's not the same if you use output information from Delaunay components, because here we need a justapposition of edges where triangles touches each others.
After this work I joined the edges and found their centroid. At the same time I found the mid point of each edge.
Now the component... (see Image_03)
It' a little bit longer to describe: I'll try to be synthetic.
Substantially it is a loft from a curve to a point, repeated three times for each triangle (Surface_Freeform_Extrude Point). The point is an elevation of the centroid of the triangle (you can choose if the exstrusion has a single height or it's related to an attractor. In my case it was fixed). The curve is combination of things. There's an arch, which starts on the edge (there's an offset from the corner) end terminates on the same edge (on the other side, obviously). While it's generation the arch passes through a third point which belong to another segment. This last connects the mid point of the original edge (base triangle) with the centroid. The result is a kind of polyline, with two segments and an arch. If you go back to the image of the component that I posted probably you'll understand what I'm saying better than with the definition.
The posit…
he picture (4).
Previously, I had a problem with generating intersections between the two directions of the beams, but a colleague helped me by extending beams, so there was no problem with lines of intersection. But this solution has generated curl (5) at the highest vertex geometry, which I ignored in order to repair it before printing, perhaps this mean my problem with my beam spread properly. Only when the beams is 19, does not jump no problem, but I still can not distribute them properly.
(1)
(2)
(3)
(4)
(5)
I tried to show as simply as possible by removing or signing my code in GHX file.
Thank you in advance for your help
…
.
Today we have gone live, and the plugin is available on Food4Rhino. You will find an installer package, sample files, and a demo video on getting started:
http://www.food4rhino.com/project/human-ui
Visit the Bitbucket Repo and poke around in the code:
https://bitbucket.org/andheum/humanui
Check out today's coverage in Architect Magazine:
http://www.architectmagazine.com/technology/nbbj-releases-human-ui-to-bring-parametric-modeling-to-the-masses_o
Finally join our group and ask any questions or post any comments here:
http://www.grasshopper3d.com/group/human-ui
See below for detailed description!
----------------------------------
Human UI
Primary Development by:
Lead Developer: Andrew Heumann / andheum / @andrewheumann
Product Manager: Marc Syp / marcsyp / @mpsyp
Contributing Developer: Nate Holland / nateholland / @_NateHolland
Gone are the days of faking a user interface by laying out sliders and text panels and hiding wires on the Grasshopper canvas. Human UI interfaces are entirely separate from the Grasshopper canvas and leverage the power of Windows Presentation Foundation (WPF), a graphical subsystem for rendering user interfaces in the Windows environment.
OLD NEW
In other words: Human UI makes your GH definition feel like a Windows app. Create tabbed views, dynamic sliders, pulldown menus, checkboxes, and even 3D viewports and web browsers that look great and make sense to anyone--including designers and clients with no understanding of Grasshopper.
Human UI has been in development at NBBJ for over a year, as part of a larger NBBJ Design Computation initiative to deliver our tools internally as Products -- with fully automated installation, managed dependencies, analytics, documentation, and “magical” user experience. Human UI has been a huge component of the user experience part of this puzzle, and we are excited to share it with the larger Grasshopper community so that others can benefit from it and contribute to its development.
The initial release of Human UI is accompanied by a few simple examples to get you started, but we have developed sophisticated user interfaces with these tools at NBBJ and will slowly be rolling out more advanced examples. We also look forward to opening up the development to the community and seeing what new features and paradigms we can add.
Download the plugin at Food4Rhino and get started building Custom UIs for Grasshopper right away! We are happy to answer any questions or field discussion in the dedicated Grasshopper Group. Please join us!
Join the Grasshopper Group
http://www.grasshopper3d.com/group/human-ui
Download the plugin + sample files
http://www.food4rhino.com/project/human-ui
Visit the Bitbucket Repo
https://bitbucket.org/andheum/humanui
We look forward to seeing where this project takes you, please share your projects made with Human UI!
Sincerely,
Design Computation Leadership Team, NBBJ
…
hopper no requiere de conocimientos de programación o scripting para permitir al diseñador trabajar de forma generativa y paramétrica. No son necesarios conocimientos previos de Grasshopper pero sí de Rhino a nivel básico.
Controlmad es Centro Formador Autorizado Rhinoceros y Rhino fab Studio.
Nuestros profesores son Instructores Autorizados Rhinoceros con experiencia universitaria, nacional e internacional.
El curso y los ejercicios a desarrollar están enfocados a diseñadores, arquitectos, ingenieros y estudiantes.
En este curso introductorio el alumno se familiarizará con términos básicos de la estructura de Grasshopper, como “listas de datos”, “dominios”, “estructuras en árbol”, etc.
Es un curso de 18 horas, con el que se pretende entrar en la lógica de trabajo de Grasshopper mediante diversos ejercicios, de forma que el alumno sea capaz posteriormente de desarrollar sus propias gramáticas, con la confianza que da comprender los términos básicos de programación sobre los que se apoya todo el sistema de trabajo de Grasshopper.Para este curso no son necesarios conocimientos previos de Grasshopper, pero sí de Rhino (a nivel básico).
También se vincula el programa con la impresión 3D aprendiendo a exportar archivos desde Grasshopper con los requisitos mínimos de impresión 3D. Se realizará una demo de impresión en el aula.
El primer día del curso se le facilita al alumno un manual-tutorial con los ejercicios a realizar, en PDF.
A la finalización del curso, y siempre que el alumno haya asistido al 80% de las clases, se le otorgará un diploma oficial acreditativo del curso.
Fechas: 5, 6, 12 y 13 de marzo
Horario: sábado y domingo 16 - 20,30h (Madrid, CET)
Lugar: Sesiones On-line en directo a través de nuestra plataforma online.controlmad.com
…
ur setup. Can you say what sensor you are using? Are you using an Arduino to write this ascii information to the serial port? If so, there may be some formatting code for the string that you'll need to do to get the Read component to function properly. I see that you were able to open the port and Start reading... so my first thought is that the data is formatted correctly....
All of the read components look for a specific character (in this case two characters) to indicate when it has reached the end of the line being read and should spit out the data. In this case, Firefly uses the Carriage Return (\r) and Line Feed (\n) to know when it has reached the end of the line. In arduino, these are automatically added to any line if you use the Serial.println("blah, blah, blah"); command. Notice, this is different from the Serial.print("nothing to see here"); command. This doesn't mean that you can't still use the regular print command... it's just you need to use the println command to indicate when you've reached the end of the line. Let's take a look at a simple example.
void setup() { Serial.begin(9600);}void loop() { int sensorValue = analogRead(A0); Serial.print("The value of the sensor is: "); Serial.println(sensorValue);
delay(20); // important to wait some small time so you aren't sending just a ton of info over to GH which will cause it to crash :(
}
The first print statement prints a string to the serial port... and the next one adds the current sensor value... and THEN adds the carriage return and line feed to start a new line. The nice thing about using these together is that you can concatenate any type of data you want. If you were to upload this sketch, you should see a sentence being printed to the serial port that says "The value of the sensor is: 512". I made up the number, but you get the idea. Notice, I also had to include a delay function. You don't always need this (there are other ways to go about this) but the important thing to note is that the loop cycle on the Arduino can run really fast. I mean... really fast. So, you wont want to send so much data over to GH, because this could flood the string buffer in the Read component and cause it to crash (eventually). It's a good idea to add some small time interval just to slow it down a bit. I should say that I've optimized the refresh rate in the next release so it's significantly faster... so hopefully this wont be as big of a problem... but hopefully that helps some.
Now... Why are you writing data to a sensor? Sensors by default are considered inputs... so I'm quite confused as to why you would want to send data back (if you are... then you need some way to handle the string data being sent from GH... this is the whole reason we built the Firefly firmata... it sets up the two-way protocol so you don't have to deal with all of that mess... If you're going to read and write, you're better off just uploading the firmata and using the Uno Read and Write components). Also, I'm not very familiar with the Hyperterm or Advanced Serial Port Terminal... but I will say that could get COM conflicts if you're trying to open the port with different tools. Anyway, I hope some of this helps you get up and running.
Cheers,
Andy
…