TB of RAM. I think I'm going to start a GoFundMe campaign to buy one for myself :)
2- The server's cost is about $13 an hour. I get free access to supercomputer through my university and xsede.org because I earned an NSF Honorable mention last March, however, the supercomputers available through both resources are a little complicated for me to use, as opposed to the one available from amazon that has Microsoft server 2012 already installed.
3- I wanted to run 400 annual glare simulations for 400 different views.
4- I tried a to perform annual glare simulation for one view on my Dell XPS that has Intel Core i7-6700HQ processor and 16GB of system memory. The simulation took 2 hours to complete. Radiance parameter ab was set to 6.
5- I wanted to obtain the batch file for each view so I can run them on the server. So I used the fly component to run all 400 simulations and closed the cmd windows, that wasn't bad ( for me at least) because I asked my son to this job for me, he was just glad to help me :)
6- I created one batch file using this cmd command:
dir /s /b *.bat > runall.bat
This created a file with the path to each .bat file. I edited this file in Notepad++ to include the word "start" at the beginning of each line. This was done using the "find and replace" dialogue box.
7- I split my newly created batch file into 3 batch files, each one has about 130 file names and " start" before the file names.
8- installed radiance on my server
9- Ran the first batch file on the server, this started 130 cmd windows performing my simulations, CPU usage was anywhere between 90% to 100% and about 105 GB of RAMs were used.
10. It took about 5 hours to complete all 130 simulations, I expected to run all in 2 hours but can't complain because this would've taken about 260 hours to run on my laptop. After the simulations done I ran the second and then the third batch files ( total of about 15 hours).
11. I got 400 valid dgb files. Couldn't be happier!
…
he time to work with it.
the project is about facade strips which turns along height. the top angle is
parallel to the facade and the bottom is max. 90 degrees twisted, but the strips
should turn diffrently to achieve more dinamic look.
first i have tried to achieve this by calculating distance between the rotation angle from points of the grid and a single point.
then i have tried to ad some more effecting points and used the distance to the divided surface (the circles are just to control the area of effection):
i manually lofted it.
the result is a bit annoying becouse the points that effect the angle are always visible:
i have triend to solve this by drawing a line and divided it to recieve points along the bottom of the geometry. the result is not working properly:
Anyway,
there must be a better/smoother way to achieve this. i would like to effect the twist of the surfaces by distance to a spline, but im just lost. can you help me please?
the problems im encountering:
0- distance spline to grid to effect the angle
1- list of x/y coordinates and angle of rotation for each point of the grid
2- export points to excel
3- lofting lines in one direction only (x1, x2, x3...)
4- reduce the list data to 2 decimal (0,00)
5- maybe angle from radian to degrees
thx…
size component supported only ground PV panels and angled roof PV panels.
Download the newest PV SWH system size component from here (Click on "View Raw" to download it. Then move the downloaded .ghuser file to File->Special Folders->User Objects Folder, an confirm to overwrite it with previously located one).
Just a few opinions on the project you are currently working on:This kind of fixed, non-transparent (overhang) PV panels attached to a building facade are vert convenient for locations with higher latitudes.The reason for this is because they (fixed overhang PV panels) are dimensioned according to the sun position at summer solstice. Elevation angles on summer solstice at higher latitude locations are lower, than those of lower latitude locations.Due to Incheon's low latitude (37), you will get rather short length of the PV panels* : less than 10 centimeters (0.097 meters in the attached .gh file below). As you have mentioned, Galapagos needs to be used too.I will just mention some of the good and bad ways in which the upper issue could be somewhat avoided:1) Increasing the vertical distance between PV panels (PV panels appear above every second window).2) Increase the tilt angle. This will increase the length of PV panels also, but will decrease the final annual AC energy output.An example of this solution has been applied at FKI building in Seoul (latitude: 37N):I already did some tests (with tilt angles: 40, 45, 55) and this does not seem like a good solution, though.3) Shrinking the "sun window" by using the minimalSpacingPeriod_ input. In Photovoltaics, a planner is suppose to make the 9h to 15h part of the sun window free of any obstructions. If you try to decrease the "sun window" to 10 to 14h, the length of your PV panels will increase. You can try to experiment a little bit with this (set your minimalSpacingPeriod_ to 21th of June 10 to 14hours). In general, shrinking the sun window on summer solstice is not a good principle during planning.4) Using tracking PV panels, not fixed ones. But Ladybug Photovoltaics components do not support this kind of PV systems. They only support fixed ones.I would personally go with the first option. You can also experiment with the second and third one.Comment back if you have any other questions.-----------------------* By "length of the PV panels" I mean the: tiltedArrayHeight_ input of the PV SWH system size component.…
ed file and code below:
Color ColorAt(Mesh mesh, int faceIndex, double t0, double t1, double t2, double t3) { // int rc = -1; var color = Rhino.Display.Color4f.Black;
if( mesh.VertexColors.Count != 0) { // test to see if face exists if( faceIndex >= 0 && faceIndex < mesh.Faces.Count ) { /// Barycentric quad coordinates for the point on the mesh /// face mesh.Faces[FaceIndex].
/// If the face is a triangle /// disregard T[3] (it should be set to 0.0).
/// If the face is /// a quad and is split between vertexes 0 and 2, then T[3] /// will be 0.0 when point is on the triangle defined by vi[0], /// vi[1], vi[2]
/// T[1] will be 0.0 when point is on the /// triangle defined by vi[0], vi[2], vi[3].
/// If the face is a /// quad and is split between vertexes 1 and 3, then T[2] will /// be -1 when point is on the triangle defined by vi[0], /// vi[1], vi[3]
/// and m_t[0] will be -1 when point is on the /// triangle defined by vi[1], vi[2], vi[3].
MeshFace face = mesh.Faces[faceIndex];
// Collect data for barycentric evaluation. Color p0, p1, p2;
if(face.IsTriangle) { p0 = mesh.VertexColors[face.A]; p1 = mesh.VertexColors[face.B]; p2 = mesh.VertexColors[face.C]; } else { if( t3 == 0 ) { // point is on subtriangle {0,1,2} p0 = mesh.VertexColors[face.A]; p1 = mesh.VertexColors[face.B]; p2 = mesh.VertexColors[face.C]; } else if( t1 == 0 ) { // point is on subtriangle {0,2,3} p0 = mesh.VertexColors[face.A]; p1 = mesh.VertexColors[face.C]; p2 = mesh.VertexColors[face.D]; //t0 = t0; t1 = t2; t2 = t3; } else if( t2 == -1 ) { // point is on subtriangle {0,1,3} p0 = mesh.VertexColors[face.A]; p1 = mesh.VertexColors[face.B]; p2 = mesh.VertexColors[face.D]; //t0 = t0; //t1 = t1; t2 = t3; } else { // point must be on remaining subtriangle {1,2,3} p0 = mesh.VertexColors[face.B]; p1 = mesh.VertexColors[face.C]; p2 = mesh.VertexColors[face.D]; t0 = t1; t1 = t2; t2 = t3; } }
/** double r = t0 * p0.FractionRed() + t1 * p1.FractionRed() + t2 * p2.FractionRed(); double g = t0 * p0.FractionGreen() + t1 * p1.FractionGreen() + t2 * p2.FractionGreen(); double b = t0 * p0.FractionBlue() + t1 * p1.FractionBlue() + t2 * p2.FractionBlue();
ON_Color color; color.SetFractionalRGB(r, g, b);
unsigned int abgr = (unsigned int)color; rc = (int) ABGR_to_ARGB(abgr); **/ var c0 = new Rhino.Display.Color4f(p0); var c1 = new Rhino.Display.Color4f(p1); var c2 = new Rhino.Display.Color4f(p2); float s0 = (float) t0; float s1 = (float) t1; float s2 = (float) t2;
float R = s0 * c0.R + s1 * c1.R + s2 * c2.R; float G = s0 * c0.G + s1 * c1.G + s2 * c2.G; float B = s0 * c0.B + s1 * c1.B + s2 * c2.B; color = new Rhino.Display.Color4f(R, G, B, 1); } } return color.AsSystemColor(); }
…
Introduzione a Grasshopper", il primo manuale su Grasshopper.
.
I corsi PLUG IT nascono dalla volontà di promuovere le nuove tecnologie digitali di supporto alla progettazione e condividere il know-how maturato attraverso ricerca, collaborazione con i più importanti studi di architettura e pubblicazioni internazionali.
.
Verranno introdotte le nozioni base di Grasshopper approfondendo le metodologie della progettazione parametrica e le tecniche di modellazione algoritmica per la generazione di forme complesse. Il corso è rivolto a studenti e professionisti con esperienza minima nella modellazione 3D e si articolerà in lezioni teoriche ed esercitazioni.
. Argomenti trattati:
- Introduzione alla progettazione parametrica: teoria, esempi, casi studio - Grasshopper: concetti base, logica algoritmica, interfaccia grafica - Nozioni fondamentali: componenti, connessioni, data flow
- Funzioni matematiche e logiche, serie, gestione dei dati - Analisi e definizione di curve e superfici
- Definizione di griglie e pattern complessi - Trasformazioni geometriche, paneling - Attrattori, image sampler
- Data tree: gestione di dati complessi - Digital fabrication: teoria ed esempi - Nesting: scomposizione di oggetti tridimensionali in sezioni piane per macchine CNC
.
Verrà rilasciato un attestato finale.
.
Ulteriori info e programma completo su: www.arturotedeschi.com e su www.edizionilepenseur.it…
ay how many valid permutations exist.
But allow me to guesstimate a number for 20 components (no more, no less). Here are my starting assumptions:
Let's say the average input and output parameter count of any component is 2. So we have 20 components, each with 2 inputs and 2 outputs.
There are roughly 35 types of parameter, so the odds of connecting two parameters at random that have the same type are roughly 3%. However there are many conversions defined and often you want a parameter of type A to seed a parameter of type B. So let's say that 10% of random connections are in fact valid. (This assumption ignores the obvious fact that certain parameters (number, point, vector) are far more common than others, so the odds of connecting identical types are actually much higher than 3%)
Now even when data can be shared between two parameters, that doesn't mean that hooking them up will result in a valid operation (let's ignore for the time being that the far majority of combinations that are valid are also bullshit). So let's say that even when we manage to pick two parameters that can communicate, the odds of us ending up with a valid component combo are still only 1 in 2.
We will limit ourselves to only single connections between parameters. At no point will a single parameter seed more than one recipient and at no point will any parameter have more than one source. We do allow for parameters which do not share or receive data.
So let's start by creating the total number of permutations that are possible simply by positioning all 20 components from left to right. This is important because we're not allowed to make wires go from right to left. The left most component can be any one of 20. So we have 20 possible permutations for the first one. Then for each of those we have 19 options to fill the second-left-most slot. 20×19×18×17×...×3×2×1 = 20! ~2.5×1018.
We can now start drawing wires from the output of component #1 to the inputs of any of the other components. We can choose to share no outputs, output #1, output #2 or both with any of the downstream components (19 of them, with two inputs each). That's 2×(19×2) + (19×2)×(19×2-1) ~ 1500 possible connections we can make for the outputs of the first component. The second component is very similar, but it only has 18 possible targets and some of the inputs will already have been used. So now we have 2×(18×2-1) + (18×2-1)×(18×2-1) ~1300. If we very roughly (not to mention very incorrectly, but I'm too tired to do the math properly) extrapolate to the other 18 components where the number of possible connections decreases in a similar fashion thoughout, we end up with a total number of 1500×1300×1140×1007×891×789×697×...×83×51×24×1 which is roughly 6.5×1050. However note that only 10% of these wires connect compatible parameters and only 50% of those will connect compatible components. So the number of valid connections we can make is roughly 3×1049.
All we have to do now is multiply the total number of valid connection per permutation with the total number of possible permutations; 20! × 3×1049 which comes to 7×1067 or 72 unvigintillion as Wolfram|Alpha tells me.
Impressive as these numbers sound, remember that by far the most of these permutations result in utter nonsense. Nonsense that produces a result, but not a meaningful one.
EDIT: This computation is way off, see this response for an improved estimate.
--
David Rutten
david@mcneel.com
Poprad, Slovakia…
Added by David Rutten at 12:06pm on March 15, 2013
te some cut sheets, but not to optmize material, rather define some cut lines. Everything that I am cutting is made of planar wood elements, but there are very specific geometries (mostly straight lines) and I have to put tolerances and radiasas at the corners in order to cut on the cnc mill. Spending time to figure out how to automate is necessary, but I am stuck!
One thing the definition is doing is taking my brep modeled components in rhino and makking them into 2d close curves and laying them side by side. It works...not ideal as its not layed out in a sheet, but that is not the most important part.
Another particular problem is that you will see some notches in the curves, which other pieces will slip into, so different slots need different specific offsets (making them larger) as a toelrance to allow for material play. This I don't even know how to set up so maybe it will just have to wait.
THE MAIN QUESTION, and super important would be, LIFESAVER:
At all 'inward' corners...which I think will always mean concave corners (most are 90 degrees, but are within to sides, instead of a corner sticking out). I'm sure its obviousy, but the reason being the outward corners a circular dril bit can cut, but inward ones need an arc profile extended beyond where the corner of the other piece will fit into. The drill bit i am using is 6mm, so 6mm diamters arcs is what i'm working with.
I have managed to put such an arc at every vertices of each cut piece. The problem being some stick outward isntead of cutting into the piece. So each one needs to be orieneted correctly. Ideally they would also only draw into inward corners, but I can always delete them out. I think maybe I am missing a more logical mathematical way of defining?
For these geometries it is not very important which side the half circle arc in on in the inward corners, but I also have some geometries that I will have to control where the circles face according to the rest of the cut piece.
The cutouts in the middle of the pieces that are curves do not need such corners obviously.
The picture is an example drawn
I hope this isn't too specific and long. in general though automating fabrication, and controling pracitcal math and orientation problems like this is itnersting to me!
THANKS…
thing that MicroStation does (or doesn't). The eternal debate between us is that they focus to the so called BIM aspect of things (and obviously on interoperability matters - that said IFC2*4 is" implemented" in certain Bentley verticals like BA and others) whilst I'm after assembly/component puzzles (and on that matter ... MS ...hmm... to put it politely is not exactly CATIA and/or NX, he he).
On the other hand this paranoid obsession with Level/Layer driven CAD (I hate it) defines a red thick line between CAD and MCAD - because the most intelligent importer can't emulate the way that Siemens NX/CATIA classifies objects - and without control power means nothing.
On the other hand Microstation V9 (...soon) has interesting scripting capabilities (think Modo rather Generative Components) ... meaning that Grasshopper could work there in a rather nice way. I think that I must talk for that to Ray (he recently ditched the ancient legacy MS render engine in favor for the Luxology/Nexus engine). Ray still is negative to buy Act3D mind (hope that you know the mother of visual scripting - the Quest3D VR thing).
On the other hand - within the broad AEC aspect - things these days are different (especially in fast developing countries the likes of UAE, Saudi Arabia, certain ex USSR "democracies" etc etc). Studies are outsourced even at Preliminary Design stage to various sub-contractors (they undertake the Study completion per discipline as well). This means that N separate groups doing M aspects of the whole ... meaning entropy^(N*M) - that's chaos in plain English.
With this in mind I'm quite (a lot) skeptical about the practical meaning of the whole exchange thing in AEC - at least with regard the countries mentioned (not to mention that several portions of a modern AEC thing are made via MCAD apps - chaos^chaos.
I'll back with more focused issues on that matter.
But the big question is: Grasshopper of Generative Components? Well...let's talk serious SS bikes instead: think a Ducati 1198 and a BMW S1000RR (I have them both): which is "best"? The thing is that not always the best bunny is the fasted bunny and not always the fasted bunny is the best bunny.
Cheers,
Peter
…
ty to work in a new and exciting space, where design, art, technology and fashion meet.
If you guys are looking for a full- or part-time job, or know an expert who is - we're happy to with meet him/her. We're located in the Lower East Side, New York.
What the person will be doing:
- Provide technical vision for product and infrastructure features
- Work with Marketing/Product Management to enhance the user experience
- Develop (with our team) our e-commerce customization platform
- Manage our real time 3D modeling platform
- Mentor 3D modelers and developers, define and document development methods, and share best practices
- Review and recommend improvements to product architecture
What we require:
- BA/BS/ BARCH degree OR CS/EE/Engineering degree preferred
- EXTENSIVE 3d modeling, rhino and grasshopper experience
- Experience building online computer games
- Experience creating natural and fractal patterns and forms in 3d
- UV Texture Mapping bit mapping (texture mapping)
- Experience managing a development team in projects with tight SCHEDULES
- Architecture, programing, scripting, Media or Fashion industry experience preferred
- Experience implementing web interfaces using XHTML, CSS, Javascript, and AJAX
- Experience in recommendation engines and algorithms
- Interest in working in an early stage fast-paced environment…
try now to integrate Geco in an interdisciplinary architectural engineering studio: hoping we can show you some nice applications of your tool, I'll keep you update and sending now details by e-mail. Here the file (very welcome to be shared). It most probably contais trivial errors by me, thanks for helping and giving some tip! Gr. Michela
FILE:
Ok, right, I see the outputs update correctly. Origin of problems must be in some different mistake I do:
- Incident radiation: I am not sure I understand what is going on: why I get so many 'not a number' ? (The Galapagos report is full of NaNs).
Bio-Diversity: 0.887 Genome[0], Fitness=NaN, Genes [89% · 44%] { Record: Too many fitness values supplied } ...
Genome[7], Fitness=NaN, Genes [74%] { Record: No fitness value was supplied } ....
Genome[9], Fitness=NaN, Genes [37% · 11%] { Record: Genome was mutated to avoid collision Record: Too many fitness values supplied }
- Daylight calculations: the geometry accumulates withouth deleting the previous models. As a consequance, results almost do not change after few varations (so, outputs get updated but do not vary). In current daylight definition: the first object being imported is the one where the grid has to fit; its setting makes it cancelling all the other objects during import. All the others, do not delete anything when imported. When running loops (manual or GA) that vary parameters, the entire geometry do not get cancelled - so I guess the loop does not pass back by the cancelling step, but imports only the geometry which has been varied by the parameters using the setting of that import component only? I will then try again by changing the order of the operations, but if you have specfic tips, let me know.
THANKS!
…