ace when I start running Galapagos/Octopus (below is "room orientation optimization" shared at http://hydrashare.github.io/hydra/viewer?owner=mostaphaRoudsari&fork=hydra_1&id=Room_Orientation_Optimization&slide=0&scale=1&offset=0,0) It may take quite some time to see some results. That's fine for the above simulation. But my real challenge is, when I am going to optimize room dimension with respect to ASE and sDA calculations, either Galapagos or Octopus goes wildly and never come up with a solution. I believe the time-consuming calculation, especially sDA with higher -ab numbers, trigger the lag a lot? Any suggestion/trick to improve it?
Most importantly, based on your experience, for example to optimize window/exterior shades sizes and achieve ASE<10% and sDA>55% (LEED v.4 requirements), Octopus (due to its capacity of multiple objectives) is the only choice? Any other approaches within grasshopper?
The alternative approach in my mind as a GH beginner is as follows. But I am not sure whether it is doable. Again, your comments will be greatly appreciated.
Since all my room/window/shades dimension are controlled by number sliders, I am thinking whether a component from GH will trigger these number sliders (not necessary to be all of them but one by one) automatically. If this is possible, I can do "data recorder" to record outputs from ASE and sDA. Eventually I will have a database of the input parameters and sDA/ASE results.
Does it make sense? Is there a component which can trigger number slider output at certain step?
Many thank!
Cheney …
he Cordyceps. Maybe some of you find this helpful/useful.
So basically, the Cordyceps is a physical module with 4 knobs and 1 slider. The knobs give an output between 1 and 1000, while the physical slider outputs 0-359. And of course, for this physical module I wrote a plugin to communicate with it. The knobs are intended to be the variables that modifies the design, while the physical slider is intended to be connected to the camera component.
Here I will put up "the recipe" for all to make their own module. You will be able to download the plugin as well.
Please send me a message if you want the 3D-files for the knobs, the box and slider knob. They've been made to directly 3D-print.
Plugin:
https://github.com/zakadjeb/Cordyceps/blob/master/Cordyceps/Cordyce...
Code for Arduino IDE:
https://github.com/zakadjeb/Cordyceps/blob/master/Arduino/_Arduino_...
What you need:
1x - Arduino (Leonardo, UNO or whatever)
4x - Potentiometers
1x - Sliding potentiometer
1x - Breadboard
Bundle of jump wires.
1. So, a potentiometer is a variable resistor, which is basically a component that changes the resistance between the voltage and the ground.
If A is supplied with 5V then B must be connected to Ground. The W will give "read" the resistance, and thus should be placed in Analog input (A0-A5) on the Arduino. The slider potentiometer works the same way.
2. Now connect the 4 pots to each their Analog input. The slider is supposed to be in A4. So to make sure:
A0: Knob1
A1: Knob2
A2: Knob3
A3: Knob4
A4: Slider
3. Now it's time to connect the voltage! Using the breadboard, the voltage can be sent through 1 line, the Ground as well. It should be quite easy to connect them.
4. Now, download the Arduino IDE and copy-paste the code I supplied above. In the IDE, you need to let it know which Arduino you're working with, and which port is should send the script.
5. Almost there. Download the plugin. Open the port you're using through the plugin. Set Start to True and the Cordyceps should be within you.
This recipe will be updated!
Let me know if there are any issues.
// Zakaria Djebbara…
he Cordyceps. Maybe some of you find this helpful/useful.
So basically, the Cordyceps is a physical module with 4 knobs and 1 slider. The knobs give an output between 1 and 1000, while the physical slider outputs 0-359. And of course, for this physical module I wrote a plugin to communicate with it. The knobs are intended to be the variables that modifies the design, while the physical slider is intended to be connected to the camera component.
Here I will put up "the recipe" for all to make their own module. You will be able to download the plugin as well.
Please send me a message if you want the 3D-files for the knobs, the box and slider knob. They've been made to directly 3D-print.
Plugin:
https://github.com/zakadjeb/Cordyceps/blob/master/Cordyceps/Cordyce...
Code for Arduino IDE:
https://github.com/zakadjeb/Cordyceps/blob/master/Arduino/_Arduino_...
What you need:
1x - Arduino (Leonardo, UNO or whatever)
4x - Potentiometers
1x - Sliding potentiometer
1x - Breadboard
Bundle of jump wires.
1. So, a potentiometer is a variable resistor, which is basically a component that changes the resistance between the voltage and the ground.
If A is supplied with 5V then B must be connected to Ground. The W will give "read" the resistance, and thus should be placed in Analog input (A0-A5) on the Arduino. The slider potentiometer works the same way.
2. Now connect the 4 pots to each their Analog input. The slider is supposed to be in A4. So to make sure:
A0: Knob1
A1: Knob2
A2: Knob3
A3: Knob4
A4: Slider
3. Now it's time to connect the voltage! Using the breadboard, the voltage can be sent through 1 line, the Ground as well. It should be quite easy to connect them.
4. Now, download the Arduino IDE and copy-paste the code I supplied above. In the IDE, you need to let it know which Arduino you're working with, and which port is should send the script.
5. Almost there. Download the plugin. Open the port you're using through the plugin. Set Start to True and the Cordyceps should be within you.
This recipe will be updated!
Let me know if there are any issues.
// Zakaria Djebbara…
you working on a PV system which will power a domestic hot water boiler?
To answer your questions:1) Each grasshopper component (ghpython being one of those too) is using grasshopper's data matching algorithm. This algorithm takes care of complex issues which may arise from combining lists with single items, data trees with different number of items per branch and so on.I think there is a way of introducing a call to other processor's threads per each inputted surface, but this will be a very difficult job, as it will require writing a custom data matching algorithm. I do not think I am up to that task.Instead I tried to introduce the multithread only to the final part of the PVsurface component and one of its time consuming parts: calculation of sun angles, solar radiation and ac/dc power output.I attached the test file below, but sadly it didn't go well: the multithreaded version mostly runs at the same time as the regular version.I do not think I am qualified enough to answer why is that so, but I think that it may have something to do with the type of the function that the multithreading is applied to: the code is suppose to run few separate functions a couple of thousand times, and work with a couple of lists. From my experience, the multithreading works the best when a single list or two are supplied to a single function. I may be wrong on this.I am very sorry to say that I can not implement this feature.2) I am not familiar if open source PV modules database has been released.But one can always download the data for specific modules from producers websites. It can then easily be transferred to a .csv file or other text file.Ladybug Photovoltaics are based on NREL's PVWatts model.In comparison with other commercial software applications, PVWatts offers a more generalized system model, with some of the values and characteristics being assumed or embedded.The Fuentes empirical thermal model we are currently using follows the same logic: it generalizes the Module characteristics. The following characteristics are only editable: module efficiency, temperature coefficient and module mount type.It may be possible to replace Fuentes with some other, less generalized 5 parameter thermal model. But as an architect, I would definitively need help on this.
Sorry if my reply did not fulfill your expectations, and thank you for the kind words!…
ive collaborative environment.
TYPE : Course module and Workshop
The event is open for anybody interested from all the fields of design, including: architecture, interior design, furniture design, product design, fashion design, scenography, and engineering.
1. COURSE MODULE (20-23 April 2014) - optional
+ type: 3 days intensive course regarding basic knowledge in parametric design (LEVEL 1)
+ software: Rhinoceros & Grasshopper
+ plugins: Kangaroo, Weaver Bird, Lunch box, Ghowl, Geco
+ achievements:
- acquainting to the components & the concept of Generative Design
- understanding the strategies in Algorithmic Design
- how to easily insert simple mathematical equation into the project to gain more control
- how to utilize proper plugins with respect to their nature of the project
- interacting with different analysis platforms such as Ecotect & remote controller
- solving several exercises with different scales( 2D- 3D ) during each phase of the workshop
2. WORKSHOP (23-27 April 2014)
A 5 day Design-Based Research Workshop exploring new techniques in Digital Architecture/Fabrication, with a specific focus on the use of generative systems and parametric modeling as tools for creative expression.
Our ultimate goal is to increasing the efficiency of utilizing digital tools in parallel with geometric performance of the primitive design agent.
+ + CONCEPT
Fashion and Architecture are both based on basic life necessities – clothing and shelter.
However, they are also forms of self-expression – for both creators and consumers.
Both fashion and architecture affect our emotional being in many ways.
The agenda of this workshop is to investigate on the overlap between these two areas of design, art & fashion.
Fashion and architecture express ideas of personal, social and cultural identity, reflecting the concerns of the user and the ambition of the age. Their relationship is a symbiotic one and throughout history, clothing and buildings have echoed each other in form and appearance. This only seems natural as they not only share the primary function of providing shelter and protection for the body, but also because they both create space and volume out of flat, two-dimensional materials.
While they have much in common, they are also intrinsically different – address the human scale, but the proportions, sizes and shapes differ enormously.
+ + + OBJECTIVES
So far, Architects have been using techniques such as folding, bending etc. to create space, structural roofs or different other structural shapes.
The agenda of this workshop goes further with the investigation of algorithmic thinking through generative tools Integrated in design.
The challenge is creating a bridge that connects these two areas of design, architecture and fashion that perform at two opposite scales.
+ + + + TECHNICAL BRIEF
In the early stages physical models and low-tech strategies will be used, allowing the participants to gain a greater understanding of materials, fabrication and assembly methods as well as simple, yet pragmatic structural solutions.
Later in the workshop these strategies will be digitalized and elaborated using software visualizing tools such as Rhinoceros and the algorithmic plug-in Grasshopper.…
ect + Geco
TUTORS:
Arturo Tedeschi (Authorized Rhino Trainer) + Maurizio Arturo Degni
Il workshop avanzato ECOLOGIC PATTERNS affronta l’impiego di strategie parametriche all’interno del processo progettuale, approfondendo l’utilizzo di Grasshopper in sinergia con plug-in, software di analisi ambientale e simulazione fisica. Obiettivo fondamentale è la generazione della forma come risultato di tecniche di form-finding e di input ambientali (solari, termici e acustici). Verranno acquisiti nuovi strumenti operativi e di simulazione al fine di costruire modelli parametrici ottimizzati in grado di adattarsi a diverse condizioni di contesto.
MORE INFO…
; GH, this one came out and rhinoceros is disappear...like this
it said " Rhinoceros5's working is stopped. because some problems occured so Rhinoceros5 can't work correctly no longer " then I have no choice but terminate Rhinoceros.
There are some discussion about RhinoIronPython installing numpy though, no one has same problem like me. so Please somebody tell me!!
and one more question...just in case, I tried to install numpy into ironPython2.7
C:\Program Files (x86)\IronPython 2.7>ipy "C:\Program Files (x86)\IronPython 2.7\ironpkg-1.0.0..py" --installBootstrapping: c:\users\owner\appdata\local\temp\tmp2nand1\ironpkg-1.0.0-1.egg 118 KB [.................................................................]
C:\Program Files (x86)\IronPython 2.7>ironpkg -hUsage: ironpkg-script.py [options] [name] [version]
.
.
.
C:\Program Files (x86)\IronPython 2.7>ironpkg scipyWrote configuration file: C:\Users\owner\.ironpkg=============================================================================Traceback (most recent call last): File "C:\Program Files (x86)\IronPython 2.7\ironpkg-script.py", line 10, in <module> File "C:\Program Files (x86)\IronPython 2.7\lib\site-packages\enstaller\main.py", line 364, in main File "C:\Program Files (x86)\IronPython 2.7\lib\site-packages\enstaller\indexed_repo\chain.py", line 27, in __init__ File "C:\Program Files (x86)\IronPython 2.7\lib\site-packages\enstaller\indexed_repo\chain.py", line 67, in add_repo File "C:\Program Files (x86)\IronPython 2.7\lib\site-packages\enstaller\utils.py", line 92, in write_data_from_url File "C:\Program Files (x86)\IronPython 2.7\Lib\urllib2.py", line 435, in open File "C:\Program Files (x86)\IronPython 2.7\Lib\urllib2.py", line 407, in _call_chain File "C:\Program Files (x86)\IronPython 2.7\Lib\urllib2.py", line 654, in http_error_302 File "C:\Program Files (x86)\IronPython 2.7\Lib\httplib.py", line 1261, in __init__ File "C:\Program Files (x86)\IronPython 2.7\lib\site-packages\enstaller\utils.py", line 73, in open_url File "C:\Program Files (x86)\IronPython 2.7\Lib\urllib2.py", line 154, in urlopen File "C:\Program Files (x86)\IronPython 2.7\Lib\urllib2.py", line 547, in http_response File "C:\Program Files (x86)\IronPython 2.7\Lib\urllib2.py", line 467, in error File "C:\Program Files (x86)\IronPython 2.7\Lib\urllib2.py", line 429, in open File "C:\Program Files (x86)\IronPython 2.7\Lib\urllib2.py", line 446, in _open File "C:\Program Files (x86)\IronPython 2.7\Lib\urllib2.py", line 407, in _call_chain File "C:\Program Files (x86)\IronPython 2.7\Lib\urllib2.py", line 1240, in https_open File "C:\Program Files (x86)\IronPython 2.7\Lib\urllib2.py", line 1167, in do_openAttributeError: 'module' object has no attribute '_create_default_https_context'
C:\Program Files (x86)\IronPython 2.7>
how can I deal with this error?…
, Engineer and Researcher from France with broad programming experience. He is the author of the City in 3D Rhinoceros plugin for creation of buildings according to geojson file and with real elevation. Guillaume already created a new component: "Address to Location". It enables getting latitude and longitude values for the given address:
2) Support of Bathymetry data: automatic creation of underwater (sea/river/lake floor) terrain. This feature is now available through new source_ input of the "Terrain generator" component. Here is an example of terrain of the Loihi underwater volcano, of the coast of Hawaii:
3) A new terrain source has been added: ALOS World 3D 30m. ALOS is a Japanese global terrain data. Gismo "Terrain Generator" component has been using SRTM 30m terrain data, which hasn't been global and was limited to -56 to +60 latitude range. With this addition, it is possible to switch between SRTM and ALOS World 3D 30m models with the use of source_ input.
4) 9 new components have been added:
"Address To Location" - finds latitude and longitude coordinates for the given address.
"XY To Location" - finds latitude and longitude coordinates for the given Rhino XY coordinates. "Location To XY" - vice versa from the previous component: finds Rhino XY coordinates for the given latitude longitude coordinates. "Z To Elevation" - finds elevation for particular Rhino point. "Rhino text to number" - convert numeric text from Rhino to grasshopper number. "Rhino unit to meters" - convert Rhino units to meters. "Deconstruct location" - deconstructs .epw location. "New Component Example" - this component explains how to make a new Gismo component, in case you are interested to make one. We welcome new developers, even if you contribute a single component to Gismo! "Support Gismo" - gives some suggestions on how to make Gismo better, how to improve it and support it.
5) Ladybug "Terrain Generator" component now supports all units, not only Meters. So any Gismo example file which uses this component, can now use Rhino units other than Meters as well. Thank you Antonello Di Nunzio for making this happen!!
Basically just forget about this yellow panel:
This panel is not valid anymore, so just use any unit you want.
6) A number of bugs have been fixed, reported in topics for the last couple of weeks. We would like to thank members in the community who invested their time in testing, finding these bugs and reporting them: Rafat Ahmed, Peter Zatko, Mathieu Venot, Abraham Yezioro, Rafael Alonso. Thank you guys!!! Apologies if we forgot to mention someone.
The version 0.0.2 can be downloaded from here:
https://github.com/stgeorges/gismo/zipball/master
And example files from here:
https://github.com/stgeorges/gismo/tree/master/examples
Any new suggestions, testing and bug reports are welcome!!…
Added by djordje to Gismo at 5:13pm on March 1, 2017
hopper) and High Definition visualizations (V-Ray) and exploring its scientific innovations supporting the users' platform philosophical ideas.
SESSIONS: 5 sessions of 8 hours (40 hours total)
E-MAIL: educacion@chconsultores.net
REGISTRATION: (55) 56 62 57 93
TECHNICAL INFO: 044 (55) 31 22 71 83
INSTRUCTORS: Have past experience working at Gehry Technologies, and participated at studios with Eric Owen Moss and Tom Wiscombe at SCI-Arc (Southern California Institute of Architecture).
Day 1: Introduction to MAYA tools, 3D exercise start.
Day 2: Continue 3D exercise.
Day 3: Original 3D architecture design.
Day 4: Grasshopper optional application on 3D architecture design.
Day 5: V-Ray Application on 3D architecture design.
30 DAY TRIAL SOFTWARE DOWNLOAD:MAYA 2012: http://www.autodesk.com/products/autodesk-maya/free-triaRHINO 4: http://s3.amazonaws.com/files.na.mcneel.com/rhino/4.0/2011-02-11/eval/rh40eval_en_20110211.exe3DS MAX 2010: http://www.autodesk.com/products/autodesk-3ds-max/free-trialVRAY FOR 3DS MAX: http://www.vray.com/vray_for_3ds_max/demo/thankyou.shtml#thankyouPHOTOSHOP e ILLUSTRATOR: https://creative.adobe.com/apps?trial=PHSP&promoid=JZXPS
www.helenico.edu.mx
www.scifi-architecture.com/#!workshops/c1wua
LIKE US ON: www.facebook.com/scifiarchitecture
…
size component supported only ground PV panels and angled roof PV panels.
Download the newest PV SWH system size component from here (Click on "View Raw" to download it. Then move the downloaded .ghuser file to File->Special Folders->User Objects Folder, an confirm to overwrite it with previously located one).
Just a few opinions on the project you are currently working on:This kind of fixed, non-transparent (overhang) PV panels attached to a building facade are vert convenient for locations with higher latitudes.The reason for this is because they (fixed overhang PV panels) are dimensioned according to the sun position at summer solstice. Elevation angles on summer solstice at higher latitude locations are lower, than those of lower latitude locations.Due to Incheon's low latitude (37), you will get rather short length of the PV panels* : less than 10 centimeters (0.097 meters in the attached .gh file below). As you have mentioned, Galapagos needs to be used too.I will just mention some of the good and bad ways in which the upper issue could be somewhat avoided:1) Increasing the vertical distance between PV panels (PV panels appear above every second window).2) Increase the tilt angle. This will increase the length of PV panels also, but will decrease the final annual AC energy output.An example of this solution has been applied at FKI building in Seoul (latitude: 37N):I already did some tests (with tilt angles: 40, 45, 55) and this does not seem like a good solution, though.3) Shrinking the "sun window" by using the minimalSpacingPeriod_ input. In Photovoltaics, a planner is suppose to make the 9h to 15h part of the sun window free of any obstructions. If you try to decrease the "sun window" to 10 to 14h, the length of your PV panels will increase. You can try to experiment a little bit with this (set your minimalSpacingPeriod_ to 21th of June 10 to 14hours). In general, shrinking the sun window on summer solstice is not a good principle during planning.4) Using tracking PV panels, not fixed ones. But Ladybug Photovoltaics components do not support this kind of PV systems. They only support fixed ones.I would personally go with the first option. You can also experiment with the second and third one.Comment back if you have any other questions.-----------------------* By "length of the PV panels" I mean the: tiltedArrayHeight_ input of the PV SWH system size component.…