Jon Mirtschin's Comments

hi, i want to transfer my rhino file in to sap2000 v20,and i'm new to sap.i found out that i should use the geometry gym plugin.so i downloaded [ggRhino6SAP20 v1.4.04.msi (31st March 2019) v20].it didn't ask me for any license during the installation.but now when i want to use the command,it says as an unknown command.what should i do?

thx

Dear Jon,

after repairing ggRhino6Karamba1.3.1 , it shows "1. Solution exception:Unlicensed!!! To activate full functionality please request a trial license by running command ggKarambaZZLicenseRequest
Run Rhino command ggKarambaZZLicenseRequest or contact Jon!"

Could you please help me to solve it? it is a little bit urgent  I'm doing my Thesis project with it...many thanks!

Sonia

Hi Jon, 

I'm trying to use the ggstage in Grasshopper to get the relevant stages into GSA.

However, it doesn't seem to like the active elements I'm inputting. I keep getting the error message '1. Solution exception:Object reference not set to an instance of an object.' Is there a trick to getting this to work? I also can't fed the ggStageProp into GSA either?

Can you help? 

Tina

sry~and my email is foodove@gmail.com, ty~

Dear Jon,

after repairing ggRhino5Karamba1.3.0 v0.1.10, it shows "1. Solution exception: Unlicensed!!! To activate full functionality please request a trial license by running command ggKarambaZZLicenseRequest
Run Rhino command ggKarambaZZLicenseRequest or contact Jon!", I ran Rhino command ggKarambaZZLicenseRequest but it doesn't work. Could you please help me to solve it? it is a little bit urgent bc I'm doing my Thesis project with it...many thanks!

Allbest,

Dove

Hi jon

I downloaded your Geometry gym Plug-in, unfortunately it does not work because its license expire. How should I do? And I have one more question: How does gtt Plug-in work?

My email address is: Eng.karami@gmail.com

Yours Sincerely

Omid

Dear Jon,

I have some serious troubles getting the surface properly meshed with equal lengths, prior to the form finding part. Perhaps Kangaroo itself is able to do this? Hope you can help because meshing odd surfaces instead of rectangular shapes is not often shown on the forum.

Yours sincerely,

Curved%20Model%20%28positive%20Gaussian%20curv.%29.gh

Dear Jon,

I am trying to import one gbXML file which was exported by Revit .I have  loaded it in Ecotect to apply material. Now, I am planning to import in Rhino to analysis in grasshopper. I have downloaded geometrygym plugin but it does not work in Rhino and just appears in grasshopper. Would you please guide and help me by offering any information how I can to import gbXML files to Rhino.

Yours sincerely,

hey Jon, 

 Im trying to use geo gym, but this legend pops out:

where can i get the free evaluation code and then extend it to the educational version

by the way thanks for sharing, and congrats for the hard work

best,

gabriel

is there any plug-in for revit 2013 32-bit too ? i just see the 64-bit version !!

hey

i am not able to learn anything from the example files as some things turn red!!! then back to orange if i remove the NAME (N) i.e. nameless component

please help

Hi Jon, thanks for adding, i'm pretty interested about your work and i've been looking around your site some time ago.

i've been using grasshopper only for quiet sometime now, so im still trying to figure out the basic stuff, but i think it would provide such a great help in doing my architectural studies combined with BIM software at hand

has there been any new update about grasshopper and archicad connection?

.JS

Hello Jon

Thanks for the add! 

Could you give me some tips of where I should start? I really want to master Grasshopper.

Hi Jon,

I am a student and I am interested in your plug-in. I would like to use that on my thesis, are there any student version?

Thank you

Great!!!

I knew we can count on you, you Australian genius !!!

Jon I took a look at your article about Rhino/Grasshopper to Vasari import.

Is there any other way to eliminate the Revit in the process of importing?

Hi Jon!

Thank you for the Geom Gym activation. I´ll be participating in a workshop that maybe will use your software!

Thanks!

Diego.

Hi Jon, thanks for the friendship and sending the license so quick!

Just one question: am I able to transfer the xml to my other computer, or do I have to send a new license request?

I stupidly sent my request from my macbook and actually need to use GG on my tower ;)