EC
1. Between hours 1:00 to 24:002. Current document units is in Meters3. Conversion to Meters will be applied = 1.0004. [1 of 7] Writing simulation parameters...5. [2 of 6] No context surfaces...6. [3 of 6] Writing geometry...7. [4 of 6] Writing materials and constructions...8. [5 of 7] Writing schedules...9. [6 of 7] Writing loads and ideal air system...10. [7 of 7] Writing outputs...11. ...... idf file is successfully written to : c:\ladybug\Freeformtower_IDF\EnergyPlus\Freeformtower_IDF.idf12. 13. Analysis is running!...14. ......
Done! Read below for errors and warnings:
15. 16. Program Version,EnergyPlus-Windows-64 8.1.0.009, YMD=2015.04.04 23:39,IDD_Version 8.1.0.00917. 18. ************* IDF Context for following error/warning message:19. 20. ************* Note -- lines truncated at 300 characters, if necessary...21. 22. ************* 577 Zone,23. 24. ************* Only last 1 lines before error line shown.....25. 26. ************* 578 Freeformbuilding27. 28. ** Warning ** IP: IDF line~578 Comma being inserted after:" Freeformbuilding" in Object=ZONE29. 30. ** Severe ** Out of range value Numeric Field#5 (Type), value=0.00000, range={>=1 and <=1}, in ZONE=FREEFORMBUILDING31. 32. ************* IDF Context for following error/warning message:33. 34. ************* Note -- lines truncated at 300 characters, if necessary...35. 36. ************* 586 BuildingSurface:Detailed,7341.
…
ved from the source surface.
3. Send the center points to the VB component.
If you send 15 points to the VB component, it will then return 15 * 4 spirals.…
Added by June-Hao Hou at 9:41pm on December 2, 2010
ll these 12500 points.
Group 1 would represent the point located at 0, 5, 10, 15, 20 etc.
Group 2 - 1, 6, 11, 16, 21 etc.
Group 3 - 2, 7, 12, 17, 22 etc.
Group 4 - 3, 8, 13, 18, 23 etc.
Group 5 - 4, 9, 14, 19, 24 etc.
I can create the pattern but the selection of points are all the points in row 0 and then all the points in row 5 and so on.
I would like the selection of points to start at the bottom left, and sequentially continue to the right and then continue on the 2nd row (left to right & bottom to top). i am hoping the pattern i am trying to achieve is more understood with the quick screen capture I uploaded.
the end goal is to be able to select all the points in the grid that are in each pattern.
Thanks in advance for any guidance with this. …
Added by Alyne Rankin at 6:53am on October 11, 2017
Pérez Albà McNeel Europe presents Rhino 5.0, Matus Nedecký (flying architecture) and Fabio Palvelli (3D Dreaming) show VRAY for Rhino and rendering services for architecture. We also show the new Wacom Cintiq 22 HD touch.
There are 2 events, the first at 15:00 and the second at 18:30. Places are limited to 30 people each.
As a special event you can switch between the events at a basic coffee seminar "Coffee - from the plant to the cup" part. Coffee Museum in Austrian society and economy museum was founded by Edmund Mayr, who injected together with Arch Wilhelm Holzbauer, the increase of the flak tower in Esterhazy Park. His passion for collecting are also due to the many exhibits that he has collected from all over the world. Additionally Mag. Just shows a quick roundup of "100 Years of Life and Living in Vienna" and how the inventions of Dr. Carl Auer von Welsbach changed the world significantly.
program: 15:00 to 15:45 Presentation software Autodesk Maya 2014 (group 1)
15:45 -. 16:00 Tour "100 years of life and living in Vienna / Dr Carl Auer von Welsbach in the Agricultural Museum (Group 1)
16:00 to 16:45 Presentation software Rhino 5.0 and VRAY (group 1)
5:00 p.m. to 6:15 p.m. basic coffee seminar "Coffee - from the plant to the cup" with Mr Edmund Mayr
18:30 to 19:15 Presentation software Autodesk Maya 2014 (Group 2)
19:15 -. 19:30 Tour "100 years of life and living in Vienna / Dr Carl Auer von Welsbach in the Agricultural Museum (Group 1)
19:30 to 20:15 Presentation software Rhino 5.0 and VRAY (Group 2)
20:15 finger found, drinks and "Come Together"
22:00 End of the event
Participation is FREE, due to the limited number of places but registration is required. To register for the event, we ask you to select the following options:
Online Registration 15:00 http://www.kkkc.at/component/seminar/?task=3&cid=5
Online Registration 18:30 http://www.kkkc.at/component/seminar/?task=3&cid=6
or by email: office@kkkc.at
or Tel: 01-545 78 25…
9 8 7 6
5 4 3 2 1 0
I am triangulating this surface. I want to select just the red vertices. As you can note, I just need the inner vertices of this surface. I could do it mannually, but if I want to change the mesh density later, I will have to pick all of them manually again later.
Can someone help me?
Tks
…