思った感じになりません。
balls の代わりにplanarカーブを直接入れてみましたがエラーが出ます。
ファンクションにしてみたところ、forループので作った数値が反映されていません。
ファンクションのインスタンス?を出力していないと思い上記のようにしましたがエラーが出てしまいます。
以上の事から自分の認識が正しいのかよくわからなくなりました・・・
python自体の深いところをわかっているわけではないので余計こんがらがりました。
そこで、for b in ballsはどのような条件または使い方であれば使えるのでしょうか?
そして、上記のように別のオブジェクトに対しての使い方はどのようにすればできるのでしょうか?
2:同じファンクション内のdist = rs.Distance(self.pos,b.pos)についてですが
この文章も for b in balls によってbはBallのインスタンスであると定義?されたためb.posがbの位置であると分かるのでしょうか?
pythonは定義しなくても動いてしまうのでどのような時に使えるのか文章見ただけではよくわかりません・・・
大変細かいことかもしれませんが、よりpythonをしっかりと理解するためにも、どなたかわかる方ご教授いただけると幸いです。…
imilar topic with a Windows 10 user, which successfully fixed this issue.If you are tiny little patient, I think we can try the same steps in your Windows 7 case.For start, try these three steps:1) Close Rhino. Restart your PC. 2) Once the PC boots up, double click on the "regMapWinGIS.cmd" file in "MapWinGIS" installation folder.3) When it closes the Command Prompt window it opened, try running Rhino, Grasshopper and drop the "Gismo Gismo" component on the canvas (Grasshopper working area).If this does not help (you get the same COM class factory CLSID error message coming out from the "Gismo Gismo" component), then try the following steps, one by one:
1) Close Grasshopper and Rhino2) Run the Revo Uninstaller Pro and uninstall your MapWinGIS application along with removing all the leftovers from the registry. You can download 30 days trial version of it from here. Here is a youtube example of a bit older Revo Uninstaller. But the important part is that is shows how registry leftovers are removed.3) Restart your PC, and once it boots again, make sure that you are logged in as an Adminstrator!4) In your Start menu's search box type: "UAC", which will find your User Account Control Settings. Click on it, and a new window will open. Set the bar on the left to "Never notify".5) Turn off your Antivirus, which ever it is.6) Download the 64 bit version of v4.9.4.2 MapWinGIS.7) Right click on downloaded MapWinGIS-only-v4.9.4.2-x64.exe file, and choose "Properties". If there is "Unblock" button click on it, and then click on "OK". If there is no "Unblock" button, just click on "OK".8) Left double click on MapWinGIS-only-v4.9.4.2-x64.exe file and install it to "C:\dev\MapWinGIS" folder. Choose "Full installation" during installation process!9) In your Start menu's search box type: "CMD". Once the "Command prompt" appears do not left click on it! Instead right click on it, and choose "Run as Administrator".10) A command prompt window will open. Type the following command:
"your_regsvr32_folder_path\regsvr32.exe" /u /s c:\dev\mapwingis\mapwingis.ocx
If command does not result in an error message, then type this one afterwards:
"your_regsvr32_folder_path\regsvr32.exe" /s c:\dev\mapwingis\mapwingis.ocx
11) If no error appeared again, then open your Rhino and Grasshopper and check what "Gismo Gismo" component prints from its "readMe!" output.If errors appeared, please post their screenshots. Thank you in advance.
Please accept my apologies for the large number of steps. Some of them are quite simple actually (click on this, download that...).…
Added by djordje to Gismo at 12:58pm on November 28, 2017
ceros.
Public concerné /
Architectes et designers, utilisateurs de Rhino souhaitant paramétrer Rhinocéros à l’aide de Grasshopper, programme
associant des composants et une structure de graphe interagissants avec le modèle Rhino.
Une bonne connaissance de Rhinocéros est nécessaire. La langue de la formation est le français.
Structure et Objectif de la formation /
La formation se déroule sur 3 jours : les 2 premières journées sont consacrées aux « fondamentaux » de Grasshopper
avec en préambule une introduction au design et à l’architecture paramétrique et leurs impacts dans la conception, la
création et la construction.
La troisième journée sous forme d’atelier est dédiée à l’étude de cas concrets proposés par les stagiaires, qui, quelques
jours avant la formation, pourront envoyer leurs projets par mail à info AT rhinoforyou DOT com
Les stagiaires, après la formation, pourront rester en contact avec les formateurs de HDA par le biais du blog
complexitys.com et le twitter @HDA_Paris. La durée de cette formation permettra d’atteindre une autonomie et une
bonne compréhension basée sur des exemples concrets.
3 Formules possibles /
3 jours ( Initiation+Atelier ) : du lundi 20 septembre au mercredi 22 septembre
2 jours ( Initiation ) : lundi 20 et mardi 21 septembre
1 jour ( Atelier ) : mercredi 22 septembre
Programme ind icatif des notions traitéES pendan t la formation /
Introduction à la conception Paramétrique . Rhinoscript, Grasshopper: différences et similarités . Interface
graphique de Grasshopper . Objets, Données, Listes . Opérateurs scalaires : La mathématique de
Grasshopper . Gestions des données : la logique de Grasshopper . Vecteurs, Points, Lignes, Surfaces : La
géométrie de Grasshopper . Listes, Arbres, Branches . Le dessin paramétrique: exercices divers et exemples
. Références, Bibliographie, Support de cours . Ateliers d’architecture et design paramétrique (3ème jour) .
Moda lité de la formation /
Venir avec un PC portable équipé de Rhinocéros version 4.0 SR 7 et de la dernière version du plug-in
Grasshopper (téléchargeable sur www.grasshopper3d.com).
Le coût du stage est de 350 € HT/jour par personne.
Réserver votre place dès que possible car les places sont limitées à 10 participants maximum.
Inscriptions et renseignements: Jacques Hababou, info AT rhinoforyou DOT com
Pour en savoir plus sur l’architecture paramétrique: www.complexitys.com…
ceros.
Public concerné /
Architectes et designers, utilisateurs de Rhino souhaitant paramétrer Rhinocéros à l’aide de Grasshopper, programme
associant des composants et une structure de graphe interagissants avec le modèle Rhino.
Une bonne connaissance de Rhinocéros est nécessaire. La langue de la formation est le français.
Structure et Objectif de la formation /
La formation se déroule sur 3 jours : les 2 premières journées sont consacrées aux « fondamentaux » de Grasshopper
avec en préambule une introduction au design et à l’architecture paramétrique et leurs impacts dans la conception, la
création et la construction.
La troisième journée sous forme d’atelier est dédiée à l’étude de cas concrets proposés par les stagiaires, qui, quelques
jours avant la formation, pourront envoyer leurs projets par mail à info AT rhinoforyou DOT com
Les stagiaires, après la formation, pourront rester en contact avec les formateurs de HDA par le biais du blog
complexitys.com et le twitter @HDA_Paris. La durée de cette formation permettra d’atteindre une autonomie et une
bonne compréhension basée sur des exemples concrets.
3 Formules possibles /
3 jours ( Initiation+Atelier ) : du lundi 20 septembre au mercredi 22 septembre
2 jours ( Initiation ) : lundi 20 et mardi 21 septembre
1 jour ( Atelier ) : mercredi 22 septembre
Programme ind icatif des notions traitéES pendan t la formation /
Introduction à la conception Paramétrique . Rhinoscript, Grasshopper: différences et similarités . Interface
graphique de Grasshopper . Objets, Données, Listes . Opérateurs scalaires : La mathématique de
Grasshopper . Gestions des données : la logique de Grasshopper . Vecteurs, Points, Lignes, Surfaces : La
géométrie de Grasshopper . Listes, Arbres, Branches . Le dessin paramétrique: exercices divers et exemples
. Références, Bibliographie, Support de cours . Ateliers d’architecture et design paramétrique (3ème jour) .
Moda lité de la formation /
Venir avec un PC portable équipé de Rhinocéros version 4.0 SR 7 et de la dernière version du plug-in
Grasshopper (téléchargeable sur www.grasshopper3d.com).
Le coût du stage est de 350 € HT/jour par personne.
Réserver votre place dès que possible car les places sont limitées à 10 participants maximum.
Inscriptions et renseignements: Jacques Hababou, info AT rhinoforyou DOT com
Pour en savoir plus sur l’architecture paramétrique: www.complexitys.com…
ceros.
Public concerné /
Architectes et designers, utilisateurs de Rhino souhaitant paramétrer Rhinocéros à l’aide de Grasshopper,
programme associant des composants et une structure de graphe interagissants avec le modèle Rhino.
Une bonne connaissance de Rhinocéros est nécessaire. La langue de la formation est le français.
Structure et Objectif de la formation /
La formation se déroule sur 3 jours : les 2 premières journées sont consacrées aux « fondamentaux » de
Grasshopper avec en préambule une introduction au design et à l’architecture paramétrique et leurs impacts
dans la conception, la création et la construction.
La troisième journée sous forme d’atelier est dédiée à l’étude de cas concrets proposés par les stagiaires, qui,
quelques jours avant la formation, pourront envoyer leurs projets par mail à - info AT rhinoforyou DOT com -
Les stagiaires, après la formation, pourront rester en contact avec les formateurs de HDA par le biais du
blog complexitys.com et le twitter @HDA_Paris. La durée de cette formation permettra d’atteindre une
autonomie et une bonne compréhension basée sur des exemples concrets.
Programme ind icatif des notions traitéES pendan t la formation /
Introduction à la conception Paramétrique . Rhinoscript, Grasshopper: différences et similarités . Interface
graphique de Grasshopper . Objets, Données, Listes . Opérateurs scalaires : La mathématique de
Grasshopper . Gestions des données : la logique de Grasshopper . Vecteurs, Points, Lignes, Surfaces : La
géométrie de Grasshopper . Listes, Arbres, Branches . Le dessin paramétrique: exercices divers et exemples
. Références, Bibliographie, Support de cours . Ateliers d’architecture et design paramétrique (3ème jour) .
Moda lité de la formation /
Venir avec un PC portable équipé de Rhinocéros version 4.0 SR 7 et de la dernière version du plug-in
Grasshopper (téléchargeable sur www.grasshopper3d.com).
Le coût du stage de 3 jours est de 1050 € HT par personne.
Réserver votre place dès que possible car les places sont limitées à 10 participants maximum.
Inscriptions et renseignements: Jacques Hababou, info AT rhinoforyou DOT com
Pour en savoir plus sur l’architecture paramétrique: www.complexitys.com…
it seems that was this. Now all is working fine !
Glad that it worked! But I am still a bit worried. Gismo components only modify the gdal-data/osmconf.ini file and no other MapWinGIS file. So your MapWinGIS installation files should not be compromised. The fact that you did not get the "COM CLSID" error message when running the "Gismo Gismo" component suggests that MapWinGIS has been properly installed. So I wonder if the cause for the permanent "invalid shapes" warning has again something with the fact that your system is again not allowing the MapWinGIS to properly edit the osmconf.ini. Maybe this problem will appear again, and again, and reinstallation of MapWinGIS every time can be somewhat bothersome.
- About the terrain generation, is it possible to have the texture from google or other provider mapped onto the terrain surface from gismo component ? (Same as using the ladybug terrain generator in fact). I try to used the image extracted by ladybug component and then applied it to the gismo terrain but the texture is rotated by 90°.
The issue with the rotation can be solved by swapping/reversing the U,V directions of the terrain surface. A slightly more important issue is that terrain surface generated with Gismo "Terrain Generator" component might have a bit smaller radius than what the radius_ input required. This stems from the fact that the terrain data first needs to be downloaded in geographic coordinate system, and then projected. Some projecting issues may occur at the very edges of the projected terrain, so I had to slightly cut out the very edges of the terrain which results in the actual terrain diameters being slightly shorted in both directions. This means that if you apply the same satellite image from Ladybug "Terrain Generator" component to Gismo "Terrain Generator" component the results may not be the same.I attached below a python component which tries to solve this issue by extending the edges of Gismo "Terrain Generator" terrain, and then cutting them with the cuboid of the exact dimensions as the radius_ input. Have in mind that this extension of the original terrain at its edges is not a correct representation of the actual terrain in that location. But rather just an extension of the isoparameteric curve of the terrain surface. So basically: some 0 to 10% (0 to 10 percent of the width and length) of the terrain around all four edges is not the actual terrain for that location, but rather just its extension.The python component is located at the very right of the definition attached below.
Also, if you would like to use the satellite images from Ladybug "Terrain Generator" component along with "OSM shapes", sometimes you may find slight differences in position of the shapes. This is due to openstreetmap data not being based on Google Maps (that's what Ladybug "Terrain Generator" component is using), but rather on Bing, MapQuest and a few others.
- About the requiredKeys_ input of OSM shapes, I understand what you mean and your advice, but in most cases I use it, the component was working fine even without input. I think it's better to extract all tags, values and keys of the selected area, instead of searching for specific ones as I try to find all data related to what I want after, isn't it ? To check what keys are present on the area also.
Ineed, you are correct.I though you were trying to only create a terrain, 3d buildings and maybe find some school or similar 3d building, for these two locations. The recommendation I mentioned previously is due to shapefiles having a limit (2044) to how many keys it can contain. This requires further testing of some big cities locations with maybe larger radii, which I haven't performed due to my poor PC configuration. But in theory, I imagine that it may happen that a downloaded .osm file may have more than 2044 keys. In that case shapefile will only record 2044 of them, and disregard the others. That was my point.But again 2044 is a lot of keys, and I haven't been checking much this in practice. For example, when I set the radius_ to 1000 meters, and use your "3 Rue de Bretonvilliers Paris" location I get around 350 something keys, which is way below the 2044.Another reason why one should use the requiredKeys_ input is to make the Gismo OSM components run quicker: for example, the upper mentioned 350 something keys will result in 350 values for each branch of the "OSM shapes" component's "values" output.Which means if you have 10 000 shapes, the "OSM shapes" component will have 10 000 branches with 350 items on each branch (values). This can make all Gismo OSM components very heavy, and significantly elongate the calculation process.With requiredKeys_ input you may end up with only a couple of tens of items per each branch.Sorry for the long reply.…
Added by djordje to Gismo at 8:57am on June 11, 2017
picture:
... and on a PC without anything attached to the serial port. When you open the port, start the read component and its timer, do you then get a stream of <empty> values in the log output? (hmmm... I suppose that's only reasonable - but still, you are also seeing this?)
I suppose that, because of the mutually exclusive behavior of both the spider and grasshopper (i.e. only one at a time can access the COM port), we can deduce that we are listening on the correct port.
Am I listening on the correct pin (if such a notion makes sense at all)? If I look back to the spider software, I see that 9 channels are listed and that it's only the measured value on channel 0 that changes when I press the load cell. Channels 1, 2, and 3 report OVERFLOW; 4, 5, 6, and 7 are pretty much constant at 0.000 to 0.005 V; and channel 8 says FFFF. I do not know how things like that work so I do not know if they reflect reading from the 9 pins on the D-sub 9 connector.
As for your BTW question: no, I don't need to record all of the sensor values. I suppose that the Out value on the Read component will always reflect the most current value and that's all that I need to get on with life. In the end, the idea is that we have 4 load cells in the 4 corners of a plate onto which a vertical pipe is fixed. Loads are then put on the top end of the pipe and we'll have to visualize both direction and magnitude of the bending moment that is calculated from the compression - tension readings from the load cells... We've done this on a scaled model and streamed load cell information into MatLab. Now we'll have to use a different datalogger and I was hoping to be able to do the post processing in Rhino.
wim…
both my plotter/cutter and wide format printer. I had been running the plotter from my main work laptop - a Win10 machine via the plotters USB port. As it turns out you can't get Win XP drivers for this USB connection so I needed another solution.
I tried to use the plotters DB25 serial port connection using an old DB9 to DB25 modem cable I had in my collection = no luck the plotter wouldn't talk. A bit more research and it turns out these plotters need a 'null modem' cross over cable to operate. I found a pic of the correct wiring online and made up my own with some cable and connectors from the local electronics hobby shop.
With this hooked up and using Hyperterminal I was able to fire some codes to the plotter directly and get a response back - winning!
At this point I got my original code working with the 'net use' redirect from LPT1 to COM1.
HOWEVER - being that the plotter was now on a COM port there are a few more interesting things you can do with it - one is being able to read the paper size/cut area from the printer.
So what I needed to to was find a way to send and receive data to/from the plotter using the serial port.
A bit of research into .NET's serial port interface and using a bunch of small pieces of test code I have manged to completely re-jig this driver.
Upgrades include:
- Direct Serial Port comms using Null Modem cable (a USB to serial adaptor + null modem should also work)
- Plot area read from the plotter - a rectangle the size of the plot area is placed on a separate layer and coloured red
- Testing to see if selected plotting curves are both closed and inside of the cutting area - with errors shown and exiting if they are not right.
- After plot 'parking' of the plot head at the end of the cut items + an adjustable offset (currently requires manual resetting of origin on the plotter before for next cut)
Great thing is it is now 100% running within Rhino Python - no DOS command line calls = no flashing up of the CMD wind. Also no temp files needed on the HDD and no limit to number of curves that can be plotted - tested with 200 or so with no issues.
Overall very happy with whole project - have learnt a LOT about Python and .NET interfacing AND ended up with a very handy/useful tool.
Cheers
DK
# This code is a WIP # It plots directly to a DGI Plotter# via the serial port
import System.IO.Ports as Portsimport rhinoscriptsyntax as rsimport time
#Some setup valuescom_port = 'COM1' #change to match plotter port baud_rate = 9600 #change to match plotter settingplotter_step = .025 #mmfinsh_offset = 10 #mm
#Delete old cutting area and cut objectsif rs.IsLayer('Cutting Area'): rs.PurgeLayer('Cutting Area')if rs.IsLayer('Cutting Objects'): rs.PurgeLayer('Cut Objects')
#Setup Serial PortMyport = Ports.SerialPort(com_port)Port_Write = Ports.SerialPort.WriteMyport.BaudRate = baud_rateMyport.ReadTimeout=5000 #5 secsMyport.Close()Myport.Open()
#Setup PlotterPort_Write(Myport, 'PU;PA0,0;IN;\n')Port_Write(Myport, 'SP1;\n')Port_Write(Myport, 'PA;\n')time.sleep(2)
#Read the Paper size from PlotterPort_Write(Myport, 'OH;') #HPGL read limits codetime.sleep(2)
return1 = ''papersize = ''count = 0char_in_buffer = 0chars_in_buffer = Ports.SerialPort.BytesToRead.GetValue(Myport)
if chars_in_buffer == 0: print 'Plotter not ready' Myport.Close() exit()
while (count < chars_in_buffer): return1 = Myport.ReadChar() papersize = papersize + chr(return1) count = count + 1
papersize = papersize.split(",")rect1 = (float(papersize[2])*plotter_step)rect2 = (float(papersize[3])*plotter_step)
print 'Cutting area = ' + str(rect1) + 'x' + str(rect2)
#place cutting area curve on its own layer, make it red and lock itplane = rs.WorldXYPlane()cutting_area = rs.AddRectangle( plane, (rect1), (rect2))rs.AddLayer (name='Cutting Area', color=(255,0,0), visible=True, locked=True, parent=None)rs.ObjectLayer(cutting_area, 'Cutting Area')
#get plotting objects
allCurves = rs.GetObjects("Select curves to plot", rs.filter.curve)
#test to see if these are closed curves - exit if not
for curve in allCurves: test_closed = rs.IsCurveClosed(curve) if test_closed == 0: print "One or move of these curves are not closed" Myport.Close() exit()
#test to see if these are inside cutting area - exit if not
for curve in allCurves: test_inside = rs.PlanarClosedCurveContainment(curve, cutting_area)
if test_inside==0 or test_inside==1: print "One or more of these curves are outside of cut area" Myport.Close() exit()
#All ok - convert to points and send data to printer
rs.AddLayer (name='Cut Objects', color=(0,255,0), visible=False, locked=True, parent=None)
for curve in allCurves: Port_Write(Myport, 'PU;PA;SP1;\n') polyline = rs.ConvertCurveToPolyline(curve,angle_tolerance=5.0, tolerance=0.025, delete_input=False, min_edge_length=0, max_edge_length=0) points = rs.CurveEditPoints(polyline) rs.ObjectLayer(polyline, 'Cut Objects')
# PU to the first point x = points[0][0] y = points[0][1] Port_Write(Myport, 'PU' + str(int(x / plotter_step)) + ',' + str(int(y / plotter_step)) + ';\n') # PD to every subsequent point i = 1 while i < len(points): x = points[i][0] y = points[i][1] Port_Write(Myport, 'PD' + str(int(x / plotter_step)) + ',' + str(int(y / plotter_step)) + ';\n') i += 1
Port_Write(Myport,'PU;\n')
#find the far end of the cutbox = rs.BoundingBox(allCurves)far_end = str(box[1])far_end = far_end.split(",")far_end = far_end[0]far_end = float(far_end)/plotter_stepfar_end = (int(far_end))+ finsh_offsetfar_end = str(far_end)print (far_end)
#return plotter home and close portPort_Write(Myport, 'PU;PA' + far_end + ',0;IN;\n')Port_Write(Myport, 'SP1;\n')Port_Write(Myport, 'PA;\n')Myport.Close()time.sleep(10)…