rk for Rhino, this is a first go at a very simple tool to get an idea of how fast different computers are at performing the sort of calculations used in Kangaroo, with the aim of informing those buying or upgrading their machines.
If you could take a couple of minutes to download and run this definition (after closing other running applications), then post here the result and your PC specs, hopefully we can start building a basic picture of what effect different hardware really has on the speed Kangaroo runs.
Most of the information can be found in the System page of Control Panel.
RAM speed can be checked in your BIOS, or with a tool like CPU-Z (note that the reported frequency from this should be doubled to get the actual RAM speed rating - eg if the frequency is 800MHz you should write DDR3-1600. It's confusing I know - see some discussion of this here), or by searching online for the specs of your PC model number.
This definition is purely testing the speed of the internal physics calculation, not display, so graphics-cards are irrelevant.
For now this is just to get a single general measure of overall Kangaroo speed, but it might also be interesting later to run a variety of tests to see how the speed varies with the size and complexity of simulation.
Of course a way of benchmarking general Grasshopper performance would be very nice to have as well, but would involve a lot more variables, and I'd be interested if anyone has ideas about how that could work.
Note - I posted a couple of versions of this earlier with various errors that were causing incorrect results. If you downloaded the earlier KangaMark01.gh or KangaMark02.gh file, please disregard that and any results from it and use the one posted here below:…
t, and it worked great!I can already see some of the nice benefits of its usage. With the Google Earth component, you made a quite a remarkable addition to the Ladybug set of components! Keep up this great work!
Just as a mention: I am attaching a screenshot of two new components:The first one: "Terrain analysis" performs a couple of terrain analysis types, and the second one: "Flow paths" performing the water flow analysis.Screenshot example of both is given below:
It would be nice if your Terrain Generator component could benefit from using these two new ones.In order to do that, Terrain Generator would have to output the terrain in a form of surface as well. My modest advice would be to add the "type_" input, which will determine whether the "terrain" output is a mesh, or a surface. This will make it consistent with Terrain Generator 2 component.To create the terrain surface from a grid of points, use the NurbsSurface.CreateThroughPoints method:
import Rhino as rcuDegree = vDegree = 3uClosed = vClosed = FalseterrainSurface = rc.Geometry.NurbsSurface.CreateThroughPoints(pts, numberOfPtsIn_vDirection, numberOfPtsIn_uDirection, uDegree, vDegree, uClosed, vClosed)
Of course this is just a suggestion, I am not imposing anything.…
I am not knowledgeable about google maps nor google maps api, but from what I read the two components will definitely show a bit different results due to different topography sources.If it is judging by this 2010 article, your Terrain Generator component offers much higher precisions for USA. Precision goes up to a couple of meters, which is amazing!!On the global scale it offers either SRTM 1 or 3 arc-second data or 30 arc-second GLOBE data. Again this is from the mentioned article, I couldn't find this information by searching the Google Maps website.Terrain Generator 2 component always uses SRTM 1 arc-second data from opentopography.org, and it is limited to 60 degrees north and does not have data for Antarctica. It does not come with satellite image either which is another very convenient feature that you have!I couldn't find information about the allowed radius provided by the Google maps api free account. I limited the "radius_" input to 100 000 meters, even though opentopography.org provides more than that (I successfully downloaded 300 000, but Rhino 5 was not able to create a topography on my PC from such a large amount of data).Even though I couldn't compare the results from two components, by looking at your upper example_LB_terrain_generator.gh definition: set the "I" input of "Surface from points" component to True. In this way the surface will be interpolated through points, which is what we want.
Again thank you for the permission, and I look forward seeing those high precision topography that Google maps offers!!…
cy of design communication and the control of information-flow are as important as the creativity of ideas. In response to the concurrent digital evolution emerging in the architectural industry world-wide, the Faculty of Architecture at The University of Hong Kong will host a two week intensive summer program named Digital Practice.Led by professors from The University of Hong Kong, as well as invited practitioners with expertise in practice of cutting edge digital techniques, the program offers participants opportunities to experience applications of computational tools during different stages of an architectural project, i.e. concept design, form finding and optimization, delivery, management and communication of design information under the team-based working environment. By learning advanced computational techniques through case studies in the context of Hong Kong, participants are expected to go beyond the conventional perception of technology, considering users and tools as a feedback-based entity instead of a dichotomy. The program, which is taught in English, includes a series of evening lectures related delivered by teaching staff and invited local architects.對於高品質的建築專案,創意之外,專案過程中高效的設計資訊管理和交流成為項目設計深化和實施必不可少的環節。今天,數字化技術不但改變了建築師的繪圖工具,影響了設計的過程,而且提供了工程建造和管理實施的更有效、更高效的手段。針對建築的數位化演進,香港大學建築學院將於2011年暑假期間,在香港大學建築學院舉辦“數位化實踐”國際研習班。在香港大學建築學院教授及有著相關豐富經驗的外聘實踐建築師的指導下,學員將有機會體驗在專案的不同階段(如概念設計、設計形式的生成、優化,設計資訊的管理和交流),如何有效地應用各種運算智慧化技術(從設計的數位化生成和建築資訊類比到物理模型),提升設計實施的品質,增加設計團隊對於方案的控制。我們將挑戰對於“技術”的傳統認知,即相對於使用者它不僅是工具,更是與使用者互動的媒介,二者形成一個有機的合體。研習班期間會安排系列講座,展現數位化技術在實踐工程中的廣泛應用。…
buildings_trees_streets.gh or color_the_buildings.gh. I think the reason why you had upper problem may have been fixed.
2) Ok, glad it worked! With my prehistoric PC, I sometimes need to leave it turned on all night long so that OSM 3D component can create buildings over a couple of hours.
3) I checked the location now. It seems that Paris in general is very poorly documented in openstreetmap.org when it comes to 3d data (having some of the following keys: height, min_height, building:levels...). But maybe this may be able to be somewhat improved by using "randomHeightRange_" input of "OSM 3D". The way you are doing it now manually with random extruding shapes. Still I may need your help on this, with testing.…
Added by djordje to Gismo at 10:06am on February 11, 2017
nstalling of 3 previous versions of Ladybird and Honeybee but nothing different happened. This was all happening on a desktop PC running windows 10 and with a wired connection to the internet router (via a switch). I then tried installing Ladybug and Honeybee on a MacBook Pro running Windows 7 on bootcamp. This computer was wirellesly connected to the same router. The installation of the latest version was very smooth and all the right files of the right sizes appeared without any problem on the first import of Honeybee-Honeybee. I then copied the files over to the other computer. Solved.
1. good thing I didn't know that as I wouldn't have kept on trying to resolve it!
2. Ok, sticking with it - besides I would hate miss out on such a major release!
3. Makes sense.
4. ok, I thought that that was the main file because of the EP in the title - I now have them both anyway.
5. Now that you say this when I click on the file in github and download it from the view raw link then I do get the right file size. But when I have been trying to download it directly from the root folder (i.e.Honeybee/resources) with "save link as" then I get the 36kB. Could it be that Honeybee_Honeybee was doing something similar?
Many thanks again to both of you - great work out there!
best,
Alex…
picture:
... and on a PC without anything attached to the serial port. When you open the port, start the read component and its timer, do you then get a stream of <empty> values in the log output? (hmmm... I suppose that's only reasonable - but still, you are also seeing this?)
I suppose that, because of the mutually exclusive behavior of both the spider and grasshopper (i.e. only one at a time can access the COM port), we can deduce that we are listening on the correct port.
Am I listening on the correct pin (if such a notion makes sense at all)? If I look back to the spider software, I see that 9 channels are listed and that it's only the measured value on channel 0 that changes when I press the load cell. Channels 1, 2, and 3 report OVERFLOW; 4, 5, 6, and 7 are pretty much constant at 0.000 to 0.005 V; and channel 8 says FFFF. I do not know how things like that work so I do not know if they reflect reading from the 9 pins on the D-sub 9 connector.
As for your BTW question: no, I don't need to record all of the sensor values. I suppose that the Out value on the Read component will always reflect the most current value and that's all that I need to get on with life. In the end, the idea is that we have 4 load cells in the 4 corners of a plate onto which a vertical pipe is fixed. Loads are then put on the top end of the pipe and we'll have to visualize both direction and magnitude of the bending moment that is calculated from the compression - tension readings from the load cells... We've done this on a scaled model and streamed load cell information into MatLab. Now we'll have to use a different datalogger and I was hoping to be able to do the post processing in Rhino.
wim…
inner As Curve() = section.ToNurbsCurve().Offset(normal, pc, -plate, 1e-3, 1e-4, Rhino.Geometry.CurveOffsetCornerStyle.Sharp)
the error message is:
"
{0}0. Error: Het oplossen van de overbelasting is mislukt omdat dit aantal argumenten door geen enkele toegankelijke Offset wordt geaccepteerd. (line 104)
"
this is the VBA script:
"Option Strict OffOption Explicit On'Import SDK and Framework namespacesImports RhinoImports Rhino.GeometryImports Rhino.CollectionsImports GrasshopperImports Grasshopper.KernelImports Grasshopper.Kernel.DataImports Grasshopper.Kernel.TypesImports GH_IOImports GH_IO.SerializationImports SystemImports System.IOImports System.XmlImports System.DataImports System.DrawingImports System.ReflectionImports System.CollectionsImports System.Windows.FormsImports Microsoft.VisualBasicImports System.Collections.GenericImports System.Runtime.InteropServices'Code generated by Grasshopper(R) (except for RunScript() content and Additional content)'Copyright (C) 2011 - Robert McNeel & Associates<System.Runtime.CompilerServices.CompilerGenerated()> _Public Class Script_Instance Implements IGH_ScriptInstance#Region "Members" ''' <summary>List of error messages. Do not modify this list directly.</summary> Private __err As New List(Of String) ''' <summary>List of print messages. Do not modify this list directly, use the Print() and Reflect() functions instead.</summary> Private __out As New List(Of String) ''' <summary>Represents the current Rhino document.</summary> Private doc As RhinoDoc = RhinoDoc.ActiveDoc ''' <summary>Represents the Script component which maintains this script.</summary> Public owner As Grasshopper.Kernel.IGH_ActiveObject#End Region#Region "Utility functions" ''' <summary>Print a String to the [Out] Parameter of the Script component.</summary> ''' <param name="text">String to print.</param> Private Sub Print(ByVal text As String) __out.Add(text) End Sub ''' <summary>Print a formatted String to the [Out] Parameter of the Script component.</summary> ''' <param name="format">String format.</param> ''' <param name="args">Formatting parameters.</param> Private Sub Print(ByVal format As String, ByVal ParamArray args As Object()) __out.Add(String.Format(format, args)) End Sub ''' <summary>Print useful information about an object instance to the [Out] Parameter of the Script component. </summary> ''' <param name="obj">Object instance to parse.</param> Private Sub Reflect(ByVal obj As Object) __out.Add(GH_ScriptComponentUtilities.ReflectType_VB(obj)) End Sub ''' <summary>Print the signatures of all the overloads of a specific method to the [Out] Parameter of the Script component. </summary> ''' <param name="obj">Object instance to parse.</param> Private Sub Reflect(ByVal obj As Object, ByVal method_name As String) __out.Add(GH_ScriptComponentUtilities.ReflectType_VB(obj, method_name)) End Sub#End Region ''' <summary> ''' This procedure contains the user code. Input parameters are provided as ByVal arguments, ''' Output parameter are ByRef arguments. You don't have to assign output parameters, ''' they will be null by default. ''' </summary> Private Sub RunScript(ByVal p0 As Point3d, ByVal p1 As Point3d, ByVal p2 As Point3d, ByVal pc As Point3d, ByVal plate As Double, ByVal itt As Integer, ByVal dev As Double, ByRef crvout As Object, ByRef crvin As Object, ByRef sec As Object, ByRef opp As Object, ByRef div As Object, ByRef pt4 As Object) 'your code goes here… opp = "test01" Dim section As New Polyline(5) section.Add(p0) section.Add(p1) section.Add(p2) section.Add(pc) section.Add(p0) Dim normal As Vector3d = vector3d.CrossProduct((p1 - p0), (p2 - p0)) Dim area As Double Dim chicken_int As Int32 = 0 Dim XX As Double Dim YY As Double Do chicken_int += 1 If (chicken_int > itt) Then Exit Do 'Compute the section offset Dim inner As Curve() = section.ToNurbsCurve().Offset(normal, pc, -plate, 1e-3, 1e-4, Rhino.Geometry.CurveOffsetCornerStyle.Sharp) Dim edges As New CurveList(inner) edges.Add(section.ToNurbsCurve()) crvin = edges Dim sections As Brep() = Brep.CreatePlanarBreps(edges) If (sections Is Nothing) Then Exit Do opp = "test02" 'Compute the centroid of the current section Dim am As AreaMassProperties = AreaMassProperties.Compute(sections(0)) Dim ct As Point3d = am.Centroid XX = am.CentroidCoordinatesMomentsOfInertia.X YY = am.CentroidCoordinatesMomentsOfInertia.Y area = am.Area Dim dx As Vector3d = pc - ct 'Compute the error of the current centroid Dim dl As Double = dx.Length div = dl 'Update output values crvout = section crvin = inner sec = sections(0) opp = area If (dl < dev) Then Exit Do 'Adjust outline with a boosting factor. section(3) += dx * 4 Loop pt4 = section(3) crvout = section End Sub '<Custom additional code> '</Custom additional code> End Class
"…
t to work. I was getting an error message on the OSMshapes components. I searched the forums and followed these steps:Close your Grasshopper and Rhino.2) Restart your PC3) When it boots up again, in your Start menu's search box type: "UAC". Click on it, and a new User Account Control Settings window will open. Set the bar on the left to "Never notify".4) Completely turn off your Antivirus.5) Check once again if your access control to the C:\MapWinGIS_installation_folder\gdal-data\osmconf.ini file is still set to the values you previously reported in this post.6) Right-click on "Rhino 5" icon and then choose: "Run as administrator".7) When Rhino boots up, run Grasshopper, and open the newest create_3dbuildings_trees_streets.gh file from here.This got the script to work and eliminated all of the error messages. The thing is... The omsconfig file's settings switch back after a some time passes, so I have to keep going back to change them. Also If I don't right click on rhino and choose "open as an adminstrator" the script won't work. I'll get those same error messages when I open Rhino normally. I'm also not super comfortable turning off my antivirus software during the time that I am working.Are there more permanant solutions that I can employ without going through these steps every time?
Thanks,
Robert…
ectural project, the efficiency of design communication and the control of information-flow are as important as the creativity of ideas. In response to the concurrent digital evolution emerging in the architectural industry world-wide, the Faculty of Architecture at The University of Hong Kong will host a two week intensive summer program named Digital Practice.Led by professors from The University of Hong Kong, as well as invited practitioners with expertise in practice of cutting edge digital techniques, the program offers participants opportunities to experience applications of computational tools during different stages of an architectural project, i.e. concept design, form finding and optimization, delivery, management and communication of design information under the team-based working environment. By learning advanced computational techniques through case studies in the context of Hong Kong, participants are expected to go beyond the conventional perception of technology, considering users and tools as a feedback-based entity instead of a dichotomy. The program, which is taught in English, includes a series of evening lectures related delivered by teaching staff and invited local architects.對於高品質的建築專案,創意之外,專案過程中高效的設計資訊管理和交流成為項目設計深化和實施必不可少的環節。今天,數字化技術不但改變了建築師的繪圖工具,影響了設計的過程,而且提供了工程建造和管理實施的更有效、更高效的手段。針對建築的數位化演進,香港大學建築學院將於2011年暑假期間,在香港大學建築學院舉辦“數位化實踐”國際研習班。在香港大學建築學院教授及有著相關豐富經驗的外聘實踐建築師的指導下,學員將有機會體驗在專案的不同階段(如概念設計、設計形式的生成、優化,設計資訊的管理和交流),如何有效地應用各種運算智慧化技術(從設計的數位化生成和建築資訊類比到物理模型),提升設計實施的品質,增加設計團隊對於方案的控制。我們將挑戰對於“技術”的傳統認知,即相對於使用者它不僅是工具,更是與使用者互動的媒介,二者形成一個有機的合體。研習班期間會安排系列講座,展現數位化技術在實踐工程中的廣泛應用。…