diseño paramétrico con Grasshopper: días 16, 17 y 18 de noviembre. Curso de iniciación a Grasshopper. Para seguirlo no se requieren conocimientos previos específicos. El objetivo de este curso es tomar contacto con Grasshopper, entender cómo funciona y empezar a fabricar y editar geometría con él. Más información y programa detallado del curso. - MÓDULO II: curso de diseño discriminativo con Grasshopper y análisis ambiental con Ecotect: días 23, 24 y 25 de noviembre. Se tratarán componentes avanzados de geometría y gestión de datos, así como soluciones evolutivas de optimización del diseño con Galapagos, y conexión con Ecotect. Más información y programa detallado del curso. - MÓDULO III: curso de diseño iterativo: scripting con Grasshopper en C#: días 30 de noviembre, 1 y 2 de diciembre. Curso de "scripting" con Grasshopper y Processing, donde se tratará de modelado recursivo con C# y RhinoCommon en Grasshopper. Formadores Los cursos están conducidos por Authorized Rhino Trainers: puedes comprobar nuestros tres años de experiencia, más de 30 cursos de Grasshopper y 300 alumnos en nuestra página web. Material El material de los cursos ha sido elaborado íntegra y exclusivamente por nosotros para estos cursos: - Manual de ejercicios de Grasshopper nivel I - Manual de ejercicios de Grasshopper nivel II - Manual de ejercicios de scripting en Grasshopper con C# Formato Cursos intensivos con duración de 18 horas con el siguiente horario: - Viernes: 17-21h - Sábado:10-14h, 16-20h - Domingo: 11-14 h, 16-19h Grupos El número de asistentes está limitado a un máximo de 10 personas para garantizar la calidad de la enseñanza y a un mínimo de 4 personas.…
Added by Miguel Vidal at 8:40am on August 30, 2012
this common installation problem please find a tested remedy shared by one of the group members:
Comment by Iman Sheikhansari on August 26, 2019 at 8:33amDelete Comment
HiIf you are encountering a problem with rhino 6 versions don't worryFollow these steps.1. Download SYNTACTIC from https://sites.google.com/site/pirouznourian/syntactic-design2. Install it and go to the installation folder, Drag & drop SYNTACTIC(green one) over your grasshopper canvas.3. Close your rhino and reopen it. 4. Type GrasshopperDeveloperSettings5. Tick the Memory load *.GHA assemblies using COFF byte arrays option6. Run grasshopper and enjoy plugin
I hope this helps,
Best regards,
Pirouz
…
inner As Curve() = section.ToNurbsCurve().Offset(normal, pc, -plate, 1e-3, 1e-4, Rhino.Geometry.CurveOffsetCornerStyle.Sharp)
the error message is:
"
{0}0. Error: Het oplossen van de overbelasting is mislukt omdat dit aantal argumenten door geen enkele toegankelijke Offset wordt geaccepteerd. (line 104)
"
this is the VBA script:
"Option Strict OffOption Explicit On'Import SDK and Framework namespacesImports RhinoImports Rhino.GeometryImports Rhino.CollectionsImports GrasshopperImports Grasshopper.KernelImports Grasshopper.Kernel.DataImports Grasshopper.Kernel.TypesImports GH_IOImports GH_IO.SerializationImports SystemImports System.IOImports System.XmlImports System.DataImports System.DrawingImports System.ReflectionImports System.CollectionsImports System.Windows.FormsImports Microsoft.VisualBasicImports System.Collections.GenericImports System.Runtime.InteropServices'Code generated by Grasshopper(R) (except for RunScript() content and Additional content)'Copyright (C) 2011 - Robert McNeel & Associates<System.Runtime.CompilerServices.CompilerGenerated()> _Public Class Script_Instance Implements IGH_ScriptInstance#Region "Members" ''' <summary>List of error messages. Do not modify this list directly.</summary> Private __err As New List(Of String) ''' <summary>List of print messages. Do not modify this list directly, use the Print() and Reflect() functions instead.</summary> Private __out As New List(Of String) ''' <summary>Represents the current Rhino document.</summary> Private doc As RhinoDoc = RhinoDoc.ActiveDoc ''' <summary>Represents the Script component which maintains this script.</summary> Public owner As Grasshopper.Kernel.IGH_ActiveObject#End Region#Region "Utility functions" ''' <summary>Print a String to the [Out] Parameter of the Script component.</summary> ''' <param name="text">String to print.</param> Private Sub Print(ByVal text As String) __out.Add(text) End Sub ''' <summary>Print a formatted String to the [Out] Parameter of the Script component.</summary> ''' <param name="format">String format.</param> ''' <param name="args">Formatting parameters.</param> Private Sub Print(ByVal format As String, ByVal ParamArray args As Object()) __out.Add(String.Format(format, args)) End Sub ''' <summary>Print useful information about an object instance to the [Out] Parameter of the Script component. </summary> ''' <param name="obj">Object instance to parse.</param> Private Sub Reflect(ByVal obj As Object) __out.Add(GH_ScriptComponentUtilities.ReflectType_VB(obj)) End Sub ''' <summary>Print the signatures of all the overloads of a specific method to the [Out] Parameter of the Script component. </summary> ''' <param name="obj">Object instance to parse.</param> Private Sub Reflect(ByVal obj As Object, ByVal method_name As String) __out.Add(GH_ScriptComponentUtilities.ReflectType_VB(obj, method_name)) End Sub#End Region ''' <summary> ''' This procedure contains the user code. Input parameters are provided as ByVal arguments, ''' Output parameter are ByRef arguments. You don't have to assign output parameters, ''' they will be null by default. ''' </summary> Private Sub RunScript(ByVal p0 As Point3d, ByVal p1 As Point3d, ByVal p2 As Point3d, ByVal pc As Point3d, ByVal plate As Double, ByVal itt As Integer, ByVal dev As Double, ByRef crvout As Object, ByRef crvin As Object, ByRef sec As Object, ByRef opp As Object, ByRef div As Object, ByRef pt4 As Object) 'your code goes here… opp = "test01" Dim section As New Polyline(5) section.Add(p0) section.Add(p1) section.Add(p2) section.Add(pc) section.Add(p0) Dim normal As Vector3d = vector3d.CrossProduct((p1 - p0), (p2 - p0)) Dim area As Double Dim chicken_int As Int32 = 0 Dim XX As Double Dim YY As Double Do chicken_int += 1 If (chicken_int > itt) Then Exit Do 'Compute the section offset Dim inner As Curve() = section.ToNurbsCurve().Offset(normal, pc, -plate, 1e-3, 1e-4, Rhino.Geometry.CurveOffsetCornerStyle.Sharp) Dim edges As New CurveList(inner) edges.Add(section.ToNurbsCurve()) crvin = edges Dim sections As Brep() = Brep.CreatePlanarBreps(edges) If (sections Is Nothing) Then Exit Do opp = "test02" 'Compute the centroid of the current section Dim am As AreaMassProperties = AreaMassProperties.Compute(sections(0)) Dim ct As Point3d = am.Centroid XX = am.CentroidCoordinatesMomentsOfInertia.X YY = am.CentroidCoordinatesMomentsOfInertia.Y area = am.Area Dim dx As Vector3d = pc - ct 'Compute the error of the current centroid Dim dl As Double = dx.Length div = dl 'Update output values crvout = section crvin = inner sec = sections(0) opp = area If (dl < dev) Then Exit Do 'Adjust outline with a boosting factor. section(3) += dx * 4 Loop pt4 = section(3) crvout = section End Sub '<Custom additional code> '</Custom additional code> End Class
"…
the end of the workshop Student performance objectives
- Understanding some basic concepts of Grasshopper, such as; Mathematical Function, Geometry, etc.
- Creating a simple parametric design system.
---------------------------------------------------
Schedule :
Deadline for Registration : April 02,2013
Workshop Starts : Thursday, April 02, 2013 - 5:30 pm
The workshop consists of 10 lectures, Each lecture lasts for 3 hours.
3 lectures per week
---------------------------------------------------
Fees :
600 L.E
You have to fill the Registration Form below for place reservation.We only have few places available.
---------------------------------------------------
Prerequisite :
-Basic knowledge of any 3d modeling software “Sketchup, 3dsmax, Rhino, Maya, ...,etc.” is required to attend the workshop.
---------------------------------------------------
Registration Form:
https://docs.google.com/forms/d/1W5CptB7FyU2d37_aqtSaBN_sxPqj7491HUN_NFgGyg8/viewform
---------------------------------------------------
Previous workshop
https://www.facebook.com/events/469048376477647/
https://www.facebook.com/media/set/?set=a.548388031851299.1073741826.470747186282051&type=1
https://www.facebook.com/events/178326265647678/…
geode. The faceting system also references the original use of triangulation for mapping three dimensional landscapes.
My question responds to the need to control the edges lengths and angles within the triangles to make the process of construction possible. We are hoping to keep the edges under 28 inches and the minimum angle more than 15 degrees. What would be your suggestion in grasshopper?
Our process for getting the facet was also... the long way.
1. draw curves based on three dimension measurements of interior
2. networks surface the four curves
3. mesh surface
4. triangulate mesh
5. reduce polygons
6. splitmeshedge where necessary to make quadrilaterals triangles once more
Any suggestions?…
Added by Amanda Gann at 8:57pm on December 4, 2013
e structure systems. It presents an algorithmic process where the initial generative rule is based on the growth of Cellular Automata (CA). Digital Fabrication techniques will be used for prototyping. Theoretical lectures about Cellular Automata, Generative design and fabrication techniques will be presented .
Duration : 21 June. – 28 June. 2013 from 10 am to 6 pm Location : ENCODE Studio Address: 2 Wataneya buildings , 14 May Bridge , Smouha , Floor 1 , Apartment 106 Tel: 03-3823637 Mob: 0100-9879995 Email: encodestudio.mail@gmail.com Website: www.encodestudio.net for more information and registration please fill the following form : https://docs.google.com/forms/d/1FC9-CIDsNuzMkmu3Rubj45_7zTBb6YB3OfYnEA9xOMk/viewform?edit_requested=true Attendance Confirmation email will be sent to confirm availability…
of the new challenges presented to the society and architecture in Portugal. With technological developments, tools once limited to not creative areas begin to be part of the everyday life of students in University Architecture Laboratories and change its design processes. The architecture design methods are changing rapidly with the introduction of CAD-CAM software’s. In recent years, new software’s have been available for 3D representation and digital fabrication, which have allowed creating new ways of interacting with the computer and architecture. Contemporary architecture in its various scales, seeks greater flexibility, adaptability and interactivity taking into account both the means and goals of kinetic systems. Thus, it is essential to the creative industry players to acquire new knowledge about the latest technological innovations and how they can solve some of the problems and challenges of today’s society.
The workshop will explore the use of Grasshopper, Firefly and Arduino as creative and technical tools in all the design process, to simulation and prototype 3D interactive architecture solutions.
The theoretical and practical workshop (64 hours) taught in English and Portuguese, will be composed of two modules: (1) LS_01: Firefly +Grasshopper + Arduino and Scale Model Fabrication; (2) LS_02: Design Studio – Discursive Wall.
This workshop is intended for students and professionals from different areas of knowledge, (architecture, design, fine arts, engineering, music and programming) who are interested in the process of design: from ideation to prototyping. The participants will generate scale models.
Registration is limited to 20 participants with or without software knowledge. Participants will work individually and in group. Participants must take their own laptops to the workshop. Registrants should complete the form by 28 February 2012. Once registered, you will receive an email confirming your acceptance.
Questions or doubts contact us:
alivingsystem@gmail.com
…
Added by Brimet Silva at 7:07pm on January 16, 2012
ll-Facade using Rhino and Grasshopper Participants will learn; Rhinoceros Grasshopper Advanced Parametric Design Brick Formations and Explorations Shadow-Design Relationship
Session 2: Advanced Digital Modeling for Additive Manufacturing (3D Printing) Participants will learn; How to prepare a 3D design to 3D Printing process in Rhinoceros Advanced Methods for 3D Print optimisation for time and cost effective production 3D Printing software education Cura
INFO
Date Saturday, 28 September 2019 Schedule 9:30am – 2:30pm (Session 1) | 2:45pm – 7:00pm (Session2) Venue (TBC) Pada Labs, Istanbul Language English/Turkish Softwares Rhinoceros Grasshopper 3D Cura Participants will need to bring their own laptops with software installed; other plugins will be distributed at the workshop. Prerequisites All tutorials are open to beginner level. No previous knowledge of Cura and Grasshopper needed. Basic knowledge of Rhinoceros recommended. Participation The workshop is limited to the first 20 applicants. Each student will receive a certificate of participation. Prices for each session: (You can pick one and attend one) Special Early registration (Deadline 1 August ) Students 310 TL Professionals 400 TL Regular registration Students 390 TL Professionals 480 TL Prices for Session 1&2 Combined: (Full Day) Special Early registration (Deadline 1 August ) Students 540 TL Professionals 690 TL Regular registration Students 620 TL Professionals 790 TL DISCOUNTS Group registration of 3 or more people will get a 15% discount. * Previous Pada workshop students will get a 10% discount. DIRECTOR Begum Aydinoglu, M.Arch AA DRL will be instructing and directing the following workshops. REGISTRATION: Email to pada.workshops@gmail.com for registration instructions. Please note that we have limited seats and there won't be any exceptions. …
a machine that is light and very sturdy. I have taken my Macbook Pro all around the world, carry it with me every day, even dropped it a few times and its still totally fine. Its thin and light.
2) You get some actual support for your hardware even a few years down the line. My Macbook Pro is from 2012 and I can still walk in to any Apple Store and get help with it, which I have done many, many times in different places around the world - I never had to show a receipt or was charged any money for help. There is no PC/Laptop manufacturer in the world with anything close to that, because companies like Asus, Dell, etc. bring out dozens of new versions of laptops every year, so its much harder to service them after a few years.
3) This is the most important one, which usually people forget when they say that Macbooks are overpriced: Resale Value. If you have ever tried to sell an old PC/Laptop (I have a few times), you will know how little value they have even after just 2-3 years. Macbooks retain their value very well and even after 4 years you can still get 50% of your original price.
4) Of course you can install Windows on it and it runs perfectly. I have MacOS and Windows on it and both run absolutely fine. On the Windows side I have Rhino+GH, Maya and a few others. Having Windows is good, because some software still only runs on Windows (looking at you, 3DSMax!). Most other software also runs on MacOS. In the interest of sanity it is great to have an alternative to Windows for all the day to day stuff, like Mail, Calender, Photos, Presentations, etc. that just always works.
5) As for performance: Yes, Macbook Pros dont necessarily have the latest and greatest in graphics cards (the rest is on par with PC laptops), but unless you want to play games you will not need it. VRay RT can do GPU rendering, but you wont get great performance from a Notebook GPU anyways and it doesnt make sense to do rendering on a laptop (especially since you have a workstation). You could get one of the older Macbook Pro Retina Late 2013 or Mid 2014 models with the GTX750M by Nvidia, which will be usable to render using VRay RT, but of course not huge performance. Better to invest in a good used graphics card for your workstation like an Nvdia GTX980ti, which is the best value for money for GPU rendering right now (lots of used ones available).
So at least consider also getting a Macbook Pro. You can buy refurbished models (depending where you are) and they are like new, but a lot cheaper or even get an older one thats used. It will be a worthwile investment.
Take it from someone who has used dozens of PCs and Macs in my lifetime and have to do the IT support here at work (where we also use both).
I still have my Macbook Pro Retina from 2012 and its still running perfectly, super fast, and I can use Rhino and GH for huge files, do GPU Rendering with Octane Render and all sorts of other heavy computing stuff.
Hope that helps.…
Added by Armin Seltz at 11:12am on September 19, 2016
思った感じになりません。
balls の代わりにplanarカーブを直接入れてみましたがエラーが出ます。
ファンクションにしてみたところ、forループので作った数値が反映されていません。
ファンクションのインスタンス?を出力していないと思い上記のようにしましたがエラーが出てしまいます。
以上の事から自分の認識が正しいのかよくわからなくなりました・・・
python自体の深いところをわかっているわけではないので余計こんがらがりました。
そこで、for b in ballsはどのような条件または使い方であれば使えるのでしょうか?
そして、上記のように別のオブジェクトに対しての使い方はどのようにすればできるのでしょうか?
2:同じファンクション内のdist = rs.Distance(self.pos,b.pos)についてですが
この文章も for b in balls によってbはBallのインスタンスであると定義?されたためb.posがbの位置であると分かるのでしょうか?
pythonは定義しなくても動いてしまうのでどのような時に使えるのか文章見ただけではよくわかりません・・・
大変細かいことかもしれませんが、よりpythonをしっかりと理解するためにも、どなたかわかる方ご教授いただけると幸いです。…