radiance parameters to get rid of blotching. To add another level of complexity to my problem, I am running simulations with a translucent material with the following properties: void trans testTrans
0
0
7 0.478 0.478 0.478 0.000 0.010 0.178 0.635
I have had no issues with the renderings when I use clear glazing, as seen on this image:
However the blotching-issue becomes very noticeable when I introduce translucent glazing into the scene:
For the two above cases I used the following parameters:
_av_ is set to 0
xScale is set to 2
_ab_ is set to 6
_dc_ is set to 0.5
_aa_ is set to 0.2
_ad_ is set to 2048
_st_ is set to 0.5
yScale is set to 2
_ps_ is set to 4
_ar_ is set to 64
_as_ is set to 2048
_ds_ is set to 0.25
_pt_ is set to 0.1
_dr_ is set to 1
_pj_ is set to 0.9
_dp_ is set to 256
_dt_ is set to 0.25
_lr_ is set to 6
_dj_ is set to 0.5
_lw_ is set to 0.01
I ran another test with increased Radiance parameters and got the following output:
with the following parameters:
_av_ is set to 0
xScale is set to 6
_ab_ is set to 6
_dc_ is set to 0.75
_aa_ is set to 0.1
_ad_ is set to 4096
_st_ is set to 0.15
yScale is set to 6
_ps_ is set to 2
_ar_ is set to 128
_as_ is set to 4096
_ds_ is set to 0.05
_pt_ is set to 0.05
_dr_ is set to 3
_pj_ is set to 0.9
_dp_ is set to 512
_dt_ is set to 0.15
_lr_ is set to 8
_dj_ is set to 0.7
_lw_ is set to 0.005
Although the second blotching case is much better than the first, it is still very bad for hours when the sun is lower in the sky. The above images are rendered for a clear sky at 18:00 in Germany in a West-facing room.
Sorry for the long post! Can someone help? Kind regards, Örn
…
lla progettazione parametrica e le tecniche di modellazione algoritmica per la generazione di forme complesse
___________________________________________________________________________________
luogo:
Sala meeting Hotel Mercure Milano Centro Piazza Oberdan 12 – 20129 MILANO
Scadenza iscrizioni: 12 Novembre 2011 – ore 15.00
___________________________________________________________________________________
info e prenotazioni:
Le Penseur (coordinamento formazione)
info@lepenseur.it
081 564 21 84
347 548 71 78
quote di partecipazione e programma (formato PDF)
ulteriori informazioni sui corsi PLUG > IT
___________________________________________________________________________________
PROGRAMMA DEL CORSO
GIORNO_01
10.00 – 10.30: presentazione workshop
10.30 – 11.30: introduzione alla progettazione parametrica: teoria, esempi, casi studio
11.30 – 13.00: Grasshopper: concetti base, logica algoritmica, interfaccia grafica
13.00 – 14.00: break | lunch
14.00 – 16.00: nozioni fondamentali: componenti, connessioni, data flow
16.00 – 18.00: esercitazione
GIORNO_02
10.00 – 12.00: funzioni matematiche e logiche, serie, gestione dei dati
12.00 – 15.00: analisi e definizione di curve e superfici
GIORNO_03
10.00 – 12.00: definizione di griglie e pattern complessi
12.00 – 13.00: trasformazioni geometriche, paneling
13.00 – 14.00: break | lunch
14.00 – 16.00: esercitazione
16.00 – 18.00: attrattori, image sampler
GIORNO_04
10.00 – 13.00: data tree: gestione di dati complessi
13.00 – 14.00: break | lunch
14.00 – 15.00: digital fabrication: teoria ed esempi
15.00 – 18.00: nesting: scomposizione di oggetti tridimensionali in sezioni e posizionamento su piani di taglio per macchine a controllo numerico CNC…
the space that you are designing and your design intent. Just think about an atrium vs a museum. And now think of the atrium in two different climate zones. As a [lighting] designer you make the decision on how do you want the space to be, how the climate is and then try to take advantage of skylight and/or direct sunlight to achieve your design goals.
2. Yes. There is a watchTheSky component next to sky types which let you visualize the sky. There is also an example file that you can check.
3. This one again depends on your model. For your model I would suggest a minimum number of 4 for your final analysis. -ab is only one of the parameters. Check this slides by John Mardaljevic if you want to have a better understanding of radiance parameters and their effect on the results.
I also added the link to "Tutorial on the Use of Daysim Simulations for Sustainable Design" by Christoph Reinhart to teaching materials. I encourage you to at least read chapters 1 and 2 of the tutorial. Check pages 25 and 27 have two examples about selecting the parameters.
Great questions. Keep them coming.
Mostapha…
the space that you are designing and your design intent. Just think about an atrium vs a museum. And now think of the atrium in two different climate zones. As a [lighting] designer you make the decision on how do you want the space to be, how the climate is and then try to take advantage of skylight and/or direct sunlight to achieve your design goals.
2. Yes. There is a watchTheSky component next to sky types which let you visualize the sky. There is also an example file that you can check.
3. This one again depends on your model. For your model I would suggest a minimum number of 4 for your final analysis. -ab is only one of the parameters. Check this slides by John Mardaljevic if you want to have a better understanding of radiance parameters and their effect on the results.
I also added the link to "Tutorial on the Use of Daysim Simulations for Sustainable Design" by Christoph Reinhart to teaching materials. I encourage you to at least read chapters 1 and 2 of the tutorial. Check pages 25 and 27 have two examples about selecting the parameters.
Great questions. Keep them coming.
Mostapha…
evel in which each final branch contains a list of one number from each list in all its variations with the other two lists.
12
AB
xy
Becomes eight possible combinations:
1Ax
1Ay
1Bx
1By
2Ax
2Ay
2Bx
2By
Either I could immediately break into 8 branches or branch twice from 2 items to 4 items then from those 4 items to 8 final items. I keep trying grafting with all manner of tree components and *never* obtain a simple dual branching fractal tree structure. I barely even need a tree actually, but I'd prefer each final branch to contain a list I can pull each final value individual value out of rather than dealing with string extraction. This is all to eventually plug all these variations into a parametric mesh model that now uses three sliders, and Python script also to bake them all as OBJ files.
Crucially I also need to obtain the numbers to use as part of my multiply exported OBJ files. I can so far only get a single range to export as a series of OBJ files automatically but not the whole three list array of them.
…
ace when I start running Galapagos/Octopus (below is "room orientation optimization" shared at http://hydrashare.github.io/hydra/viewer?owner=mostaphaRoudsari&fork=hydra_1&id=Room_Orientation_Optimization&slide=0&scale=1&offset=0,0) It may take quite some time to see some results. That's fine for the above simulation. But my real challenge is, when I am going to optimize room dimension with respect to ASE and sDA calculations, either Galapagos or Octopus goes wildly and never come up with a solution. I believe the time-consuming calculation, especially sDA with higher -ab numbers, trigger the lag a lot? Any suggestion/trick to improve it?
Most importantly, based on your experience, for example to optimize window/exterior shades sizes and achieve ASE<10% and sDA>55% (LEED v.4 requirements), Octopus (due to its capacity of multiple objectives) is the only choice? Any other approaches within grasshopper?
Many thank!
Cheney
…
ing basic concepts for personalization in footwear design and fabrication in order to send afterwards to CNCs, laser cutting equipment, 3D printers, etc.
Note: Previous knowledge in Rhinoceros and footwear design is not necessary.Content:1. Personalization in footwear upper(Working with a digital shape from a 3D scan)2. Shoe sole creation3. Using Grasshopper to create women's heels4. Nesting and using the work area5. Basic programming for a mold and/or a mock-up for CNC - RhinoCAM
Requirements: 1 PC or LaptopSoftware: Punto3D, provided by a CD which includes necessary demo programs, as well as the files that will be used for the session. Rhinoceros 5.0 for WindowsGrasshopperRhinoCAM 2014RhinoNEST 2014NOTE: You have to bring your own computer with Rhino 5 installed.
Register:
http://www.mcneelmiami.com/inc/sdetail/1727
//
Diseño y fabricación digital de Calzado
Lugar: Sala Ejecutiva 4
Precio: $95.00 USD
Idioma de curso: Español
Profesor: José de Jesús López Martínez. Punto3D, ART (Authorized Rhino Trainer)
Descripción: Compartir conceptos básicos para la personalización de cortes de calzado y el diseño de accesorios. Para su posterior envío a dispositivos como CNC's, equipos de corte láser, impresoras 3D, entre otros. Nota: No es necesario tener conocimientos previos de Rhinoceros, ni de diseño de calzado.
Contenido:
1. Personalización de corte de calzado (Trabajo sobre horma digital, la cual proviene de un escaneado 3D)
2. Creación de una suela
3. Grasshopper para la creación de un tacón para calzado de dama
4. Nesting y el aprovechamiento de áreas de trabajo
5. Programación básica de un molde y/o maqueta para CNC – RhinoCAM
Requisitos: 1 PC o Laptop
Software: Punto3D, proveerá un CD que incluirá los programas Demos necesarios, así como los archivos para trabajar en la sesión
Rhinoceros 5.0 para Windows
Grasshopper
RhinoCAM 2014
RhinoNEST 2014
NOTA: Tienes que llevar tu computador con Rhino 5 ya instalado
Regístrate:
http://www.mcneelmiami.com/inc/sdetail/1727…
content from the "bin" folder to the "c:\ladybug\terrain shading mask libraries 64-bit" folder:
So not the very bin folder, but its content.Just do this and the component will work.
Hi Abraham,
But just want to remind that Marios Tsiliakos developed a component for unblocking the LB_HB components and libraries (Unblock All and Unblock).
Thank you for the suggestion. I am aware of that component. I shared an article about it on my facebook account last year, at the time when it was released. It's a great component!There are still two issues with it: It edits the windows registry.I order for it to edit the windows registry it requires an account with administrator's rights.To unblock the file manually you do not need to have an account with administrator's rights.
BTW i installed the release-1800-x64-gdal-2-1-0-mapserver-7-0-1.zip without issues (just unblocking).
Yes, the GDAL 2.x.x and MapServer 7.x.x versions will also work. But I can not install them on my PC, therefor I can not provide support for them. The GDAL 1.x.x and MapServer 6.x.x are sufficient for what the component does.If you intend to seek support for any future issues, please install the latest GDAL 1.x.x and MapServer 6.x.x version as said by the component installation instructions.…
I am not knowledgeable about google maps nor google maps api, but from what I read the two components will definitely show a bit different results due to different topography sources.If it is judging by this 2010 article, your Terrain Generator component offers much higher precisions for USA. Precision goes up to a couple of meters, which is amazing!!On the global scale it offers either SRTM 1 or 3 arc-second data or 30 arc-second GLOBE data. Again this is from the mentioned article, I couldn't find this information by searching the Google Maps website.Terrain Generator 2 component always uses SRTM 1 arc-second data from opentopography.org, and it is limited to 60 degrees north and does not have data for Antarctica. It does not come with satellite image either which is another very convenient feature that you have!I couldn't find information about the allowed radius provided by the Google maps api free account. I limited the "radius_" input to 100 000 meters, even though opentopography.org provides more than that (I successfully downloaded 300 000, but Rhino 5 was not able to create a topography on my PC from such a large amount of data).Even though I couldn't compare the results from two components, by looking at your upper example_LB_terrain_generator.gh definition: set the "I" input of "Surface from points" component to True. In this way the surface will be interpolated through points, which is what we want.
Again thank you for the permission, and I look forward seeing those high precision topography that Google maps offers!!…
ram.com/Helicoid.html.
To be more precise, I'm not quite clear how to apply this equation to the helicoid and integrate it into my code:
where corresponds to a helicoid and to a catenoid.
I've made some attempts not worth to be shown here. Maybe somebody can help me with a pseudocode or a simple description how to start solving this classic geometric transformation.
Thanks, Sebastian
…
Added by Sebastian at 11:19am on December 27, 2012