do is to make a structural analysis of the model with Geomgym in GSA and use that gathered data to optimize the variables.
I already created the beams (with their profiles and material) and I started with creating the nodes. However, I constantly get an error when I try to open the model in GSA. GSA doesn't recognize all of the nodes I created in Grasshopper and connected to the 'create node' box from Geometry Gym.
What I need to do is find all of the intersection points of the horizontal beams, the vertical ring sections, the diagonals and the supporting beams. These supporting beams carry the weight of the actual (concrete) floor of the footbridge and the load from the floor of the footbridge needs to be loaded to the intersection of the 'supporting beams' with the 'vertical rings' (as point loads), so not with the diagonals. And I also need all points on the first and last ring section to make that nodes restraint as pins.
The division of the polygons in the vertical ring sections is recognized in GSA, but I can't figure out what is going wrong in the model. Below I added the file as I made it with the creation of the nodes included. I also added a file where the creating of the nodes isn't added.
The first added picture shows the error in GSA and the nodes GSA can't find have a red circle around it. It also says that GSA recognizes '7 structures'...
The second picture shows that the loading of forces is correctly recognized and also the pins in the first and last ring section are applied correctly. But GSA doesn't recognize the intersection points of the diagonals with the ring sections and the supporting beams...
All of the intersections between the beams need to be hinged connections, without restraints. The hinges where the forces are loaded into (z-direction) are the intersection points of the 'supporting beams' and the 'vertical ring sections'.
All of the hinges in the first and the last ring section are pinned (x,y,z restraint - xx,yy,zz not restraint).
Could anyone please help?
Thank you in advance!
…
ion, extract structural data, produce 2d drawings, and exchange data with other external software. Nemo also includes free tools to create parametric shapes, such as Naca profiles, hydrofoils, keels, rudders, blade propellers, and sail plans.
Born in 2018 as an academic research project at ENSTA Bretagne, Nemo grew up since, immersed in professional naval architecture practice with L2Onaval.
From 2021, Nemo is now available for purchase with commercial or educational licenses. Following license levels are provided to fit every needs depending of user activity :
Free (Designer)
Level 1 (Section + Hydrostatics + Visualization)
Level 1 + 2 (Section + Hydrostatics + Visualization + Resistance + Structure)
We can also help you make best use of our software, provide project guidance, establish specific workflow and create custom tools.
Requirements
Microsoft Windows 10 or Apple Mac OS 12 Monterey :
McNeel Rhinoceros 7 SR26
(Other Rhinoceros, Windows and Mac OS versions have not been tested but may work)
Additional info
Food4Rhino Download
Discourse Forum
Facebook Page
Linkedin Page
Nemo Website
Credits
Authors : Mathieu VENOT
Contributors : Paul POINET, Laurent DELRIEU
…
curve or locus] of a segment AB, in English. The set of all the points from which a segment, AB, is seen under a fixed given angle.
When you construct l'arc capable —by using compass— you obviously need to find the centre of this arc. This can be easily done in GH in many ways by using some trigonometry (e.g. see previous —great— solutions). Whole circles instead of arcs provide supplementary isoptics —β-isoptic and (180º-β)-isoptic—. Coherent normals let you work in any plane.
Or you could just construct β-isoptics of AB by using tangent at A (or B). I mean [Arc SED] component.
If you want the true β-isoptic —the set of all the points— you should use {+β, -β} degrees (2 sides; 2 solutions; 2 arcs), but slider in [-180, +180] degrees provides full range of signed solutions. Orthoptic is provided by ±90º. Notice that ±180º isoptic is just AB segment itself, and 0º isoptic should be the segment outside AB —(-∞, A] U [B, +∞)—. [Radians] component is avoidable.
More compact versions can be achieved by using [F3] component. You can choose among different expressions the one you like the most as long as performs counter clockwise rotation of vector AB, by 180-β degrees, around A; or equivalent. [Panel] is totally avoidable.
Solutions in XY plane —projection; z = 0—, no matter A or B, are easy too. Just be sure about the curve you want to find the intersection with —Curve; your wall— being contained in XY plane.
A few self-explanatory examples showing features.
1 & 5 1st ver. (Supplementary isoptics) (ArcCapableTrigNormals_def_Bel.png)
2 & 6 2nd ver. (SED) (ArcCapableSED_def_Bel.png)
3 & 7 3rd ver. (SED + F3) (ArcCapableSEDF3_def_Bel.png)
4 & 8 4th ver. (SED + F3, Projection) (ArcCapableSEDProjInt_def_Bel.png)
If you want to be compact, 7 could be your best choice. If you prefer orientation robustness, 5. Etcetera.
I hope these versions will help you to compact/visualize; let me know any feedback.
Calculate where 2 points [A & B] meet at a specific angle is just find the geometrical locus called arco capaz in Spanish, arc capable in French (l'isoptique d'un segment de droite) or isoptic [curve or locus]
of a segment AB, in English. The set of all the points from which a segment,
AB, is seen under a fixed given angle.…
he "return" is comment out as shown below?
After restarting Rhino and Grasshopper, I opened the outdoors_airflow demo file, and the first step of creating the case file is ok:
Then the blockMesh component gives the following error: seems I have to manually start OF first..
so, as the error message suggested, I open OF by Start_OF.bat:
Then come back to the blockMesh component, now it can be executed while the OF command line window is also openning:
... and the blockMesh finished successfully:
... so I proceeded to run snappyHexMesh, checkMesh and update fvScheme:
... up to the simpleFoam component, I got the error again:
The warning message is:
1. Solution exception: --> OpenFOAM command Failed!#0 Foam::error::printStack(Foam::Ostream&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #1 Foam::sigFpe::sigHandler(int) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #2 ? in "/lib64/libc.so.6" #3 double Foam::sumProd<double>(Foam::UList<double> const&, Foam::UList<double> const&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #4 Foam::PCG::solve(Foam::Field<double>&, Foam::Field<double> const&, unsigned char) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #5 Foam::GAMGSolver::solveCoarsestLevel(Foam::Field<double>&, Foam::Field<double> const&) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #6 Foam::GAMGSolver::Vcycle(Foam::PtrList<Foam::lduMatrix::smoother> const&, Foam::Field<double>&, Foam::Field<double> const&, Foam::Field<double>&, Foam::Field<double>&, Foam::Field<double>&, Foam::Field<double>&, Foam::Field<double>&, Foam::PtrList<Foam::Field<double> >&, Foam::PtrList<Foam::Field<double> >&, unsigned char) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #7 Foam::GAMGSolver::solve(Foam::Field<double>&, Foam::Field<double> const&, unsigned char) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #8 Foam::fvMatrix<double>::solveSegregated(Foam::dictionary const&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libfiniteVolume.so" #9 Foam::fvMatrix<double>::solve(Foam::dictionary const&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam" #10 Foam::fvMatrix<double>::solve() in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam" #11 ? in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam" #12 __libc_start_main in "/lib64/libc.so.6" #13 ? in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam"
... and the command lines in the readMe! output are pretty long and it is saved in the text file attached here.
So, my questions are:
1. why I have to manually start OF first before I can use the blockMesh component? Should butterfly automatically start OF?
2. what might be the cause of the unsuccessful run of simpleFoam in the end?
Hope you can kindly advise! Thank you!
- Ji
…
eration!
See an example work flow for designing, simulating and analysing a Photovoltaic system below.
Download a Grasshopper and Rhino example file:
https://www.dropbox.com/s/krbszlplj5i40dz/017_HBgeneration%20Rhino%20model.3dm?dl=0
https://www.dropbox.com/s/lxneuzal3mipd2q/017_HBgeneration.gh?dl=0
See a quick introduction and tutorial videos here: https://www.youtube.com/playlist?list=PLrx2KnyhaJ5YXo5hpk8Q9q4Vy99O5IegK
1. Select a building to mount a photovoltaic generator on (seen in Rhino in green).
2. Select a surface within that building to mount a photovoltaic generator on (seen in Rhino in green).
3. Create a Honeybee context surface from that surface.
4. Place a photovoltaic generator on that Honeybee context surface by using the Honeybee generation component. Honeybee_Generator_PV and connecting the context surface to it's input _HBSurfaces. Then you can specify both the performance and the financial data of the photovoltaic generator.
5. Create a Honeybee generation system which consists of the photovoltaic generator in 4. By using the component Honeybee_generationsystem and connecting 4 to its input PVHBSurfaces_. Then you can specify the annual maintenance cost of this system.
6. Run the simulation in Energy Plus by connecting 5. to the input HBGenerators_.
7. Read the results of the simulation:
- The electricity produced by the Honeybee generation system in 5.
- The net purchased electricity of the facility (the Honeybee zone) to which the Honeybee generation system is attached to. This is the electricity consumed by the facility less the electricity generated by the Honeybee generation system.
- The financial costs of the Honeybee generation system; capital, maintenance and replacement costs.
8. Calculate the net present cost of the Honeybee generation system in 5 assuming a 25 year lifetime.
9. Visualise the net present cost.
…
nd improvements. Many of the new features and components announced in the last release have become stable and have emerged from their WIP section. Additionally, after two years of work, we are happy to announce that we finally have full support of an OpenStudio connection within Honeybee, which has ushered in a whole host of new features, notably the modelling of detailed HVAC systems. As always you can download the new release from Food4Rhino. Make sure to remove the older version of Ladybug and Honeybee and update your scripts.
LADYBUG
1 - Solar Hot Water Components Out of WIP
After much beta-testing, bug-fixing, and general development, all of the Photovoltaic and Solar Hot Water components are now fully out of WIP! The main component is based on a Chengchu Yan's publication. Components have been added to Ladybug thanks to the efforts of Chengchu Yan and Djordje Spasic.. See Djorje’s original release post of the solar hot water components for more information on the components that just made it out of WIP.
2 - New Terrain Shading Mask Released in WIP
In addition to Djordje’s prolific addition of renewable energy components, he has also contributed a widely-useful component to generate terrain shading masks, which account for the shading of surrounding mountains/terrain in simulations. While initially added to assist the solar radiation radiation and renewable energy components, the component will undergo development to optimize it for energy and daylight simulations over the next few months. Another new component called Horizon Angles can be used to visualize and export horizon angles. You can test them out now by accessing them in the WIP section. For more information, see Djordje’s release post on the GH forum here.
3 - New Mesh Selector Component
After realizing that the Optimal Shade Creator component has applications to a whole range of analyses, it has now been re-branded as the Mesh Selector and has been optimized to work easily with these many analyses. Specifically, the component selects out the portion of a mesh that meets a given threshold. This can be the portion of a shade benefit analysis meeting a certain level of shade desirability, the portion of a radiation study meeting a certain level of fulx, the portion of a daylight analysis meeting a certain lux threshold, and much more!
4 - Solar Adjusted Temperature Now Includes Long Wave Radiation
Thanks to a question asked by Aymeric and a number of clarifications made by Djordje Spasic, the Solar Adjusted Temperature component now includes the ability to account for long-wave radiative loss to the sky in addition to it original capability to account for short wave radiation from the sun. As such, the component now includes all capabilities of similar outdoor comfort tools such as RayMan. The addition of this capability is also paralleled by the addition of a new horizontalInfraredRadiation output on the ImportEPW component. See the updated solar adjusted example file hereto see how to use the component properly.
5 - Support for both Log and Power Law Wind Profiles
In preparation for the future release of the Butterfly CFD-modelling insect, the Ladybug Wind Profile component now includes the option of either power law or log law wind profiles, which are both used extensively in CFD studies. Thanks goes to Theodoros Galanos for providing the formulas!
6 - New Radiant Asymmetry Comfort Components
Prompted by a suggestion from Christian Kongsgaard, Ladybug now includes components to calculate radiant asymmetry discomfort! For examples of how to use the components see this example file for spatial analysis of radiant asymmetry discomfort and this example for temporal analysis.
7 - Pedestrian Wind Comfort Component Released in WIP
In preparation for the impending release of the butterfly CFD-modelling insect, Djordje Spasic with assistance from Liam Harrington has contributed a component to evaluate outdoor discomfort and pedestrian safety. The component identifies if certain areas around the building are suitable for sitting, building entrances-exits, window shopping... based on its wind microclimate. Dangerous areas due to high wind speeds are also identified.You can check it out now in the WIP section.
HONEYBEE
1 - New HVAC Systems and Full OpenStudio Support
After a significant amount of development on the part of the OpenStudio team and two years of effort on the part of LB+HB developers, we (finally!) have full support for an OpenStudio connection within Honeybee. By this, we mean that any energy simulation property that can be assigned to a HBZone will be taken into account in the simulation run by the OpenStudio component. The connection to OpenStudio has brought with it several new capabilities. Most notably, you can now assign full HVAC systems and receive energy results in units of electricity and fuel instead of simple heating and cooling loads. This Honeybee release includes 14 built-in HVAC template systems that can be assigned to the zones, each of which can be customized:
0. Ideal Air Loads 1. PTAC | Residential 2. PTHP | Residential 3. Packaged Single Zone - AC 4. Packaged Single Zone - HP 5. Packaged VAV w/ Reheat 6. Packaged VAV w/ PFP Boxes 7. VAV w/ Reheat 8. VAV w/ PFP Boxes 9. Warm Air Furnace - Gas Fired 10.Warm Air Furnace - Electric 11.Fan Coil Units + DOAS 12.Active Chilled Beams + DOAS 13.Radiant Floors + DOAS 14.VRF + DOAS
Systems 1-10 are ASHRAE Baseline systems that represent much of what has been added to building stock over the last few decades while systems 11-14 are systems that are commonly being installed today to reduce energy use. Here is an example file showing how to assign these systems in Honeybee and interpret the results and here is an example showing how to customize the HVAC system specifications to a wide variety of cases. To run the file, you will need to have OpenStudio installed and you can download and install OpenStudio from here.
In addition to these template systems within Honeybee, the OpenStudio interface includes hundreds of HVAC components to build your own custom HVAC systems. OpenStudio also has a growing number of user-contributed HVAC system templates that have been integrated into a set of scripts called "Measures" that you can apply to your OpenStudio model within the OpenStudio interface. You can find these system templates by searching for them in the building components library. Here is a good tutorial video on how to apply measures to your model within the OpenStudio interface. Honeybee includes a component that runs these measures from Grasshopper (without having to use the OpenStudio interface), which you can see a demo video of here. However, this component is currently in WIP as OpenStudio team is still tweaking the file structure of measures and it is fairly safe to estimate that, by the next stable release of Honeybee, we will have full support of OpenStudio measures within GH.
2 - Phasing Out IDF Exporter
With the connection to OpenStudio now fully established, this release marks the start of a transition away from exporting directly to EnergyPlus and the beginning of Honeybee development that capitalizes on OpenStudio’s development. As such THIS WILL BE THE LAST STABLE RELEASE THAT INCLUDES THE HONEYBEE_RUN ENERGY SIMULATION COMPONENT.
The Export to OpenStudio component currently does everything that the Run Energy Simulation component does and, as such, it is intended that all GH definitions using the Run Energy Simulation component should replace it with the OpenStudio component. You can use the same Read EP Result components to import the results from the OpenStudio component and you can also use the same Energy Sim Par/Generate EP Output components to customize the parameters of the simulation. The only effective difference between the two components is that the OpenStudio component enables the modeling of HVAC and exports the HBZones to an .osm file before converting it to an EnergyPlus .idf.
For the sake of complete clarity, we should state that OpenStudio is simply an interface for EnergyPlus and, as such, the same calculation engine is under the hood of both the Export to OpenStudio component and the Run Energy Simulation component. At present, you should get matching energy simulation results between the Run Energy Simulation component and a run of the same zones with the OpenStudio component (using an ideal air system HVAC).
All of this is to say that you should convert your GH definitions that use the Run Energy Simulation component to have the OpenStudio component and this release is the best time to do it (while the two components are supported equally). Additionally, with this version of Honeybee you will no longer need to install EnergyPlus before using Honeybee and you will only need to install OpenStudio (which includes EnergyPlus in the install).
3 - New Schedule Generation Components
Thanks to the efforts of Antonello Di Nunzio, we now have 2 new components that ease the creation of schedule-generation in Honeybee. The new components make use of the native Grasshopper “Gener Pool” component to give a set of sliders for each hour of the day. Additionally, Antonello has included an annual schedule component that contains a dictionary of all holidays of every nearly every nation (phew!). Finally, this annual schedule component can output schedules in the text format recognized by EnergyPlus, which allows them to be written directly into the IDF instead of a separate CSV file. This will significantly reduce the size of files needed to run simulations and can even reduce the number of components on your canvas that are needed to add custom schedules. For more information, see Antonello’s explanatory images here and Antonello's example file here. You can also see a full example file of how to apply the schedules to energy simulations here.
4 - EnergyPlus Lookup Folder, Re-run OSM/IDF, and Read Result Dictionary
With the new capabilities of OpenStudio, we have also added a number of components to assist with managing all of the files that you get from the simulation. In particular, Abraham Yezioro has added a Lookup EnergyPlus Folder component that functions very similarly to the Lookup Daylight Folder component. This way, you can run an Energy simulation once and explore the results separately. Furthermore, we have added components to Re-Run OpenStudio .osm files or EnergyPlus .idf files within Grasshopper. These components are particularly useful if you edit these .osm or .idf files outside of Honeybee and want to re-run them to analyze their results in Grasshopper. Lastly, a component has been added to parse the .rdd (or Result Data Dictionary) file that EnergyPlus produces, enabling you to see all of the possible outputs that you can request from a given simulation.
5 - Electric Lighting Components Out of WIP
After Sarith Subramaniam’s initial components to model electric lights with Radiance in the last release, we are happy to report that they have been fully tested and are out of WIP. Improvements include support for all types of light fixture geometries and the ability to use the components in a more “Grasshoppery” list-like fashion. See Sarith’s original release post for more information and several example files showing how to use the components can be found here. 1 , 2 , 3 .
6 - Improvements to THERM Components
A number of bug fixes and improvements have been made to the THERM components in order to make their application more flexible and smooth. Special thanks is due to Derin Yilmaz , Mel King , Farnaz , Ben (@benmo1) , and Abraham Yezioro for all of the great feedback in the process of improving these components.
7 - HBObject Transform Components
After some demand for components that can ease the generation of buildings with modular zone types, two components to transform HBObjects with all of their properties have been added to the 00 | Honeybee section. The components allow you to produce copies of zones that are translated or rotated from the original position.
8 - Comfort Maps Supports PET and Integration of CFD Results
Thanks to the addition of the ‘Physiological Equivalent Temperature’ (PET) component by Djordje Spasic in the last stable release, it is now possible to make comfort maps of PET with Honeybee. PET is particularly helpful for evaluating OUTDOOR comfort with detailed wind fields at a high spatial resolution. As such, the new PET recipe has also been optimized for integration with CFD results. The windSpeed_ input can now accept the file path to a .csv file that is organized with 8760 values in each column and a number of columns that correspond to the number of test points. Components to generate this csv from Butterfly CFD results will be coming in later releases. Stay tuned!
As always let us know your comments and suggestions.
Enjoy!Ladybug Analysis Tools Development Team
…
ization processes aiming in maximizing the quality of buildings based on the daylighting, light levels, radiation and views. The first webinar in the Optimization Bundle introduce participants to metaheuristic optimization solving techniques. The training will cover evolutionary and particle swarm optimization applied to environmental problems such as radiation or amount of sunlight hours confronted with views. Grasshopper plug-ins used: Silvereye, Galapagos, Octopus, Opossum, Ladybug, Honeybee, Elk, Leafcutter Adrian KrężlikAdrian is a co-founder of Architektura Parametryczna - the biggest Polish firm dedicated to parametric education and co-founder of Parametric Support, a Berlin tech startup developing optimizationtechniques for architecture.He worked and collaborated on large scale projects in China, Saudi Arabia, US for the most innovative companies like Zaha Hadid Architects in London, FREE Fernando Romero, Rojkind Arquitectos inMexico implementing digital strategies into design. In his work he focuses on use of new media in design and construction processes. He is an active player across parametric scene - teaching andorganizing workshops, participating in Design Weeks, lecturing Parametric Design and Robotic Fabrication at School of Form and collaborating with several universities.The online webinar lasts 2 hours. The same session takes place twice on 7 January 2017: 1st session (https://goo.gl/haXsus): 9am London, 10am Paris, 12pm Moscow, 1pm Dubai, 2:30pm Mumbai, 5pm Beijing, 6pm Tokyo, 8pm Melbourne 2nd session (https://goo.gl/S6463C): 10am Los Angeles, 1pm New York, 6pm London, 7pm Paris, 9pm Moscow www.rese-arch.org…
Added by Jan Pernecky at 1:04pm on January 2, 2017
ace Syntax." eCAADe 2013 18 (2013): 357.
http://www.sss9.or.kr/paperpdf/mmd/sss9_2013_ref048_p.pdf
The measure Entropy is newer. I hereby explain it (from my PhD dissertation):
Entropy values, as described in (Hillier & Hanson, The Social Logic of Space, 1984) and specified in (Turner A. , “Depthmap: A Program to Perform Visibility Graph Analysis, 2007), intuitively describe the difficulty of getting to other spaces from a certain space. In other words, the higher the entropy value, the more difficult it is to reach other spaces from that space and vice-versa. We compute the spatial entropy of the node as using the point depth set:
(11)
“The term is the maximum depth from vertex and is the frequency of point depth *d* from the vertex” (ibid). Technically, we compute it using the function below, which itself uses some outputs and by-products from previous calculations:
Algorithm 4: Entropy Computation
Given the graph (adjacency lists), Depths as List of List of integer, DepthMap as Dictionary of integer
Initialize Entropies as List(double)
For node as integer in range [0, |V|)
integer How_Many_of_D=0
double S_node=0
For depth as integer in range [1, Depths[node].Max()]
How_Many_of_D=DepthMap.Branch[(node,depth)].Count
double frequency= How_Many_of_D/|V|
S_node = S_node - frequency * Math.Log(frequency, 2)
Next
Entropies [node] = S_node
Next
…
e I perform an offset operation on a number of curves across a surface, which then form the geometry for a series of rib structural members. It's worked flawlessly previous to this, but just started going weird today. I suspect it is something to do with me moving up to release .8.0001 from .7. I've attached the definition and surface. The problem seems to occur right at the beginning of the definition. The rest I think can be ignored. I've tried tracing back for a cause, but am coming up with no solution.
Previous to today:
Upon opening the definition today:
As you can see, the two 'ribs' on the rightmost side are offsetting in the opposite direction to the rest. I've tried playing with the plane that the offset references, reversing vectors, and other things, but I've reached a dead-end.
I would greatly appreciate any help in understanding or rectifying this, as it has me absolutely confused.
The problem seems to be occurring here:
.ghx and .3dm surface attached.
…
advanced and it has some bottlenecks that could be great to solve.
Beginners could find interesting the method used to extract values from an image that uses a custom colour scheme to represent data (is not possible to extract hue values directly) or the simple displacement method used. These are the curves that follows the colors in the reference color gradient used by NASA in RGB (up) and HSV space:
You can see that there is no linearity or constant change in any channel, either RGB or HSV space.
There is some bottlenecks in the definition that you must take care about: data comparation component (Find Similar Members) and surface closest point (Surface CP). If you want to improve it, please do it, but send me the modified version ;)
Take care of not raise or push down the values in sliders without saving or know perfectly how much data your computer is able to calculate without memory problems. The main sample image is really big and the more resolution you set, more memory it will take to sample and calculate.
Thanks to Andrea Graziano for data links :)
And...Have fun!
Link to my blog post: Blurrypaths…