he organizers of the webinar have generously decreased the cost for registration to just $10 so this is a good opportunity to get into the daylight components if you have been looking for one.You can register for the event by going to this address:https://attendee.gototraining.com/r/6086496514016899074Hope to see see you there!…
EC
1. Between hours 1:00 to 24:002. Current document units is in Meters3. Conversion to Meters will be applied = 1.0004. [1 of 7] Writing simulation parameters...5. [2 of 6] No context surfaces...6. [3 of 6] Writing geometry...7. [4 of 6] Writing materials and constructions...8. [5 of 7] Writing schedules...9. [6 of 7] Writing loads and ideal air system...10. [7 of 7] Writing outputs...11. ...... idf file is successfully written to : c:\ladybug\Freeformtower_IDF\EnergyPlus\Freeformtower_IDF.idf12. 13. Analysis is running!...14. ......
Done! Read below for errors and warnings:
15. 16. Program Version,EnergyPlus-Windows-64 8.1.0.009, YMD=2015.04.04 23:39,IDD_Version 8.1.0.00917. 18. ************* IDF Context for following error/warning message:19. 20. ************* Note -- lines truncated at 300 characters, if necessary...21. 22. ************* 577 Zone,23. 24. ************* Only last 1 lines before error line shown.....25. 26. ************* 578 Freeformbuilding27. 28. ** Warning ** IP: IDF line~578 Comma being inserted after:" Freeformbuilding" in Object=ZONE29. 30. ** Severe ** Out of range value Numeric Field#5 (Type), value=0.00000, range={>=1 and <=1}, in ZONE=FREEFORMBUILDING31. 32. ************* IDF Context for following error/warning message:33. 34. ************* Note -- lines truncated at 300 characters, if necessary...35. 36. ************* 586 BuildingSurface:Detailed,7341.
…
6, 7, 8, 9, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28, 30, etc
In addition to the components in the attached file, I have also tried using Cull Index but that did not do much. I tried using a number slider set to whole numbers with the range equal to the values I have set up in the integer, but it just increases the size by 1 every time. Any help on steps in the right direction would be great thanks.…
work. If you have been looking for an opportunity to get into a new part of the software or just want to get updated on the latest developments in a 90-minute presentation, then these webinars are for you. Starting this Thursday at 12:30 EST, the workshops will begin by covering basic Ladybug capabilities and will provide a survey of the latest community resources. Each Thursday, there will be another presentation covering progressively advanced topics. In total there will be 5 workshops, each of which you can register for by clicking below:
1 - Ladybug Climate Analysis - August 25th, 12:30 PM EST2 - Ladybug Facade + Shade Design - September 1st, 12:30 PM EST3 - Honeybee Energy, HVAC + Indoor Comfort Modeling - September 8th, 12:30 PM EST4 - Honeybee Daylight + Electric Light - September 15th, 12:30 PM EST5 - Honeybee THERM + WINDOW - September 22nd, 12:30 PM EST
Notably, workshops 2, 3, 4 and 5 will feature substantial coverage of capabilities that do not currently have tutorial videos. This includes new view analysis and tips and tricks for radiation studies in webinar 2, newly-released HVAC capabilities for webinar 3, electric lighting capabilities with webinar 4, and all of webinar 5 will be brand-new hot-off-the-press development! Hope that you can attend!…
tecipanti impareranno ad accedere ai comandi, a gestire parametricamente le geometrie importate da Rhino o generate in Grasshopper, a popolare superfici con componenti variabili, a gestire tecniche di tassellazione.…
Added by cesare griffa at 8:49am on January 21, 2012
run the simulation I get this in the command line:
An error occured in the display pipeline @ 10:35:29(856ms)An error occured in the display pipeline @ 10:35:29(856ms)An error occured in the display pipeline @ 10:35:30(387ms)An error occured in the display pipeline @ 10:35:30(387ms)
etc
etc
I have tried changing between Windows and Open GL in 'Pipeline and Conduits' settings in Options> Appearance> Advanced Settings> Other Settings - doesn't solve the problem.
I am running:
- Rhino 4 SR 8
- Grasshopper 0.80004
- Kangaroo 0.044
rhino model and grasshopper definition attached....
any help would be really appreciated!!
thanks,
Jeg…
lute_extrudersteps = 1
xbar_heightfromnozzletip = 30
xbar_width = 30
If you add these to your config file (and adjust appropriately) it should work fine. In future there may be more additions to the config file as we try and take into account the way other firmware interprets g-code, but these will be listed in the release notes.
…