in reality gives meshes out instead. There also seems to be an issue in the component, as in instead of giving the shadow region ( mesh) it is giving a mesh spanning the entire site. however if I just use 2 blocks out of the 28 blocks I am getting accurate result. please help.…
heating? Or cooling?)
What if you have 20C? You need to heat to 24-26?
What if you have 28? Then you cool to 24-26?
Something is missing here ...
Or am i wrong? (In this case i don't understand the logic).
Besides that, you are simulating 3 zones instead of 1. Your conncetions of all the HB_setEPZoneSchedules to the HB_setEPIdealAir is causing this. Messy ... a little bit.
-A.…
g it still dose not bake.
Sub RunScript(ByVal Points As List(Of Object), ByVal GridName As String, ByVal Bake As Boolean, ByVal Num As Integer)
If( Not Bake ) Then
m_count = 0
Return
End If
'Iterate through points by row
Dim i As Integer
Dim j As Integer
j = 0
For i = 0 To Points.Count() – 1
If( j > Num + 1 ) Then
j = 0
End If
Dim pt As On3dPoint
pt = Points(i)
'Name the point
Dim att As New On3dmObjectAttributes
doc.GetDefaultObjectAttributes(att)
att.m_name = GridName & "(" & m_count & ")(" & j & ")"
print(m_count)
'increment index
j += 1
'Add to document
doc.AddPointObject(pt, att)
Next
m_count += 1
A = m_count
End Sub…
h the solution to use domain with range, but I don't think it's optimized. I'm sure there is a simple way to archive it.
See screenshot below.
Regards,
David…
edia and technology. Under the umbrella of MASSv.1.0 Robots and Cyborgs International Workshop and will be supported by a series of lectures. The workshop will integrate the use of a robotic fabrication with Virtual Reality. …
edia and technology. Under the umbrella of MASSv.1.0 Robots and Cyborgs International Workshop and will be supported by a series of lectures. The workshop will integrate the use of a robotic fabrication with Virtual Reality.
…
. I did not check it so my last components were dated back to February 28. (I am kind of a few months behind). I copied them manually into the right folder.
I was even wondering a while ago why there is no sets panel, but since I did not used it, I forgot about it...
Thanks, now there is a few months to explore...…
he installation folder, Drag & drop SYNTACTIC(green one) over your grasshopper canvas.3. Close your rhino and reopen it. 4. Type GrasshopperDeveloperSettings5. Tick the Memory load *.GHA assemblies using COFF byte arrays option6. Run grasshopper and enjoy plugin…
which doesn't exist in the actual problem spec. If galapagos is allowed to change the column position in all possible directions, it is less likely to get stuck in some local optimum.
Let's assume that (all other things being equal) column 20 would yield the best possible answer. The current state of the system though is at column 26, which is pretty good too, just not as good. Galapagos is more likely to 'mutate' the state a little bit instead of a lot, so it'll explore the columns near 26. However 20 isn't near 26 at all, only 25 and 27 are nearby, and maybe 24 and 28. But they'll all worse answers, so after sampling in those directions GP will abandon that as fruitless.
If however you specify the columns using two variables, then the columns near 26 are 20, 25, 27 and 32. That's a far richer space to explore which much better approximates the real problem.…
"INTERFACES: ARCHITECTURE . ENGINEERING . SCIENCE".
Applications are still open for the Karamba workshop (between September 20 - 24) lead by Clemens Preisinger and Moritz Heimrath - "Optimization of Statically Informed Grid-Shell Patterns".…