being driven by the wii nunchuck... But, here's my issue. I tried it first by having the output from the listener be a 6-digit number... so, I'm using the (CInt(Val(StoredValue))) command and it's writing out 181130... and I can easily split it up selecting the Left(x,3) or Right(x,3)... I first rant that number through a Format("{0:000000}",x) so that even if one of the accx or accy numbers were a 2-digit number (so my overall number would only have 5-digits)... with this Format function... I'm always assured a 6-digit number. And this method works... except...
If the first group of numbers coming in only has 2-digits... So, lets say the accelerometer read out of the first one (accx) is 89. Let's say the accy read out is 119. So, when I run this through the Format function to make it have at least 6 digits, my number now reads 011989. So, if I were to take the first three numbers on the right, my read out would be 989... which is much higher than my expected (60-180 range that is really coming over the Serial Port)... So, I'm back to where I started... in that I need to figure out a better way to split up the data.
Which brings me to your method. I tried it as well... in fact, I added a comma in the serial readout, so the string coming out of the listener reads 89,119. So, I can use your trick to go look for a delimeter and then read to the left and right a certain number of digits... The problem I still have is that the data going into the function is a string, and thus even if I split the 3 digits to the right of the comma out (so, my output says 119)... it's still a string, and my number parameter is still red. In your picture above, was your original 181 130 a number or a string? My guess is that it was understood as a number, because your number parameters at the end are accepting the value. But, in my case... I'm still stuck with the inability to convert a string to a number... Does this make sense? And are their any other workarounds?…
Added by Andy Payne at 9:42am on September 3, 2009
st sampled into data trees (if not we must "add" them "manually" == code: get this item from Rhino and put it there) into collections.
2. Then we must perform some kind of selection(s) on a per individual item basis and THAT is in 99% of cases "manual" (== code) or on a per "global basis" (hard or soft clusters et all == code). If clusters are hierarchical and some kind of dendrogram is required ... this obviously means ... er ... more code.
3. Doing the 2 we use some kind of input by means of sliders (say pairs of 2: for branches and items) and therefor MAY their values cause slider control issues (== code). For instance IF this slider yields a x event > do this and that to some other sliders.
4. Then perform the "histogram" required and obviously treat this as just a variant (i.e. a possible solution out of a given collection witch is variable) meaning ways to "store" this into parameter(s) (as persistent data). This also requires code.
In a nutshell (and oversimplified): given a collection of "shapes" pick some make the histogram, store the result (or do something with that and store the outcome as well) recall some other for any reason, modify it, stored it ... and then repeat until the end of time (or worst: until you are out of espresso).
As I said: NOT a task for a novice AND NOT a task for someone not familiar with code matters (But I guess that you qualify in both areas, he he).
I do this type of things day in day out (but for real-life AEC purposes) therefor I could make a "simple demo" (add some "" more) but ... well ... you are warned, he he
But in case that you take the wrong decision (you are warned) we must use Skype a bit.…
m
-Area of blue line: min. 80% of the rectangel a x b
-Max. hight h of the top point: h,max = a
-Min. Volume between rectangel a x b and membrane: 500 m3
Can anyone help me?…
ou will see all of the available components on a ribbon at once so there is no need to keep clicking drop down menus.
It's all about discoverability with GH. What if you're a beginner and don't know about the Create Facility (dbl click canvas) how can you find Extr?
Even if you hover over every component or use the drop down lists you will not see the name Extr appear anywhere.
Sure it makes sense that Extr is short for Extrude but it's also the Nick Name of Extrude to Point component
So you can easily miss the fact that one has a Distance Input verses a Point Input.
I think I made the move to Icons around about the move from version 0.5 to 0.6, possibly before. I initially thought that I would go back to text because I loved the mono chromatic look of the text but I soon realised that Icons were the way forward. The greatest benefit is speed. You don't need to digest and decipher every component (which is written 90 degrees to the norm).
I'm not saying you should move to Icons forthwith but at least consider that once you have a better knowledge and understanding of GH, Icons will set you free.
My top ten tips that I would highly recommend to anyone wanting to better themselves with GH.
1) Turn on Draw Icons
2) Turn on Draw Fancy Wires
3) Turn on Obscure Components
4) Use the Create Facility like a Command Line eg "Slider=-1<0.75<2" or "Shiftlist=-1"
5) Use Component Aliases to customise your use of the Create Facility eg giving the Point XYZ component an alias of XYZ will bring it up as the first option on the Create Facility as opposed to the other possibilities.
6) Try to answer other people's questions even if it's not relevant to your own area. By looking into solving a problem outside of your comfort zone and then posting your results it is very rewarding but it also lets you see the other approaches that get posted in a new light.
7) Take the time to understand Data/Path structures.
8) Buy a second monitor - There is nothing that can compare to real estate when working in Grasshopper.
9) Read Rajaa Issa's Essential Mathematics
10) Pick a panel in a tab on the ribbon and get to know every component inside and out and then move on. Start with the Sets Tab > List Panel…
Integer = 0 To 9
val *= 2
lst.Add(val)
Next
Since val is a ValueType, when we assign it to the list we actually put a copy of val into the list. Thus, the list contains the following memory layout:
[0] = 2
[1] = 4
[2] = 8
[3] = 16
[4] = 32
[5] = 64
[6] = 128
[7] = 256
[8] = 512
[9] = 1024
Now let's assume we do the same, but with OnLines:
Dim ln As New OnLine(A, B)
Dim lst As New List(Of OnLine)
For i As Integer = 0 To 9
ln.Transform(xform)
lst.Add(ln)
Next
When we declare ln on line 1, it is assigned an address in memory, say "24 Bell Ave." Then we modify that one line over and over, and keep on adding the same address to lst. Thus, the memory layout of lst is now:
[0] = "24 Bell Ave."
[1] = "24 Bell Ave."
[2] = "24 Bell Ave."
[3] = "24 Bell Ave."
[4] = "24 Bell Ave."
[5] = "24 Bell Ave."
[6] = "24 Bell Ave."
[7] = "24 Bell Ave."
[8] = "24 Bell Ave."
[9] = "24 Bell Ave."
To do this properly, we need to create a unique line for every element in lst:
Dim lst As New List(Of OnLine)
For i As Integer = 0 To 9
Dim ln As New OnLine(A, B)
ln.Transform(xform)
lst.Add(ln)
Next
Now, ln is constructed not just once, but whenever the loop runs. And every time it is constructed, a new piece of memory is reserved for it and a new address is created. So now the list memory layout is:
[0] = "24 Bell Ave."
[1] = "12 Pike St."
[2] = "377 The Pines"
[3] = "3670 Woodland Park Ave."
[4] = "99 Zoo Ln."
[5] = "13a District Rd."
[6] = "2 Penny Lane"
[7] = "10 Broadway"
[8] = "225 Franklin Ave."
[9] = "420 Paper St."
--
David Rutten
david@mcneel.com
Poprad, Slovakia…
Added by David Rutten at 6:26am on September 9, 2010
ky.exe did not accept -p parameter and made empty sky.cal file.
----
Edit: solved run problem, Bee did not download OpenStudioMasterTemplate.idf
Get it here: https://github.com/mostaphaRoudsari/Honeybee/issues/119
Now get empty HDR:
C:\ladybug\prox\imageBasedSimulation>rpict -i -t 10 -vtv -vp 245.129 -226.458 20 0.405 -vd -0.549 0.656 -0.518 -vu -0.332 0.397 0.855 -vh 42.862 -vv 26.991 -v l 0 -vs 0 -vl 0 -x 800 -y 600 -af prox_RAD_Perspective.amb -ps 8 -pt 0.15 -pj 0.6 -dj 0 -ds 0.5 -dt 0.5 -dc 0.25 -dr 0 -dp 64 -st 0.85 -ab 2 -ad 1024 -as 175 -ar 150 -aa 0.200 -lr 4 -lw 0.050 -av 0 0 0 prox_RAD.oct 1>prox_RAD_Perspectiv e.unf rpict: 0 rays, 0.00% after 0.0000 hours rpict: skybright`c__ladybug_skylib_cumulativeSkies_SINGAPORE_SGP_SINGAPORE_SGP_1 : undefined variable rpict: 1020 rays, 4.91% after 0.0000 hours
----
Hi friends,
trying to get a cumulative sky image metric to run and encountered an issue with the image-based metrics component. It throws:
Runtime error (KeyNotFoundException): honeybee_materialLib Traceback: line 768, in main, "<string>" line 1442, in script
I guess this is some sort of setup issue on my end, or I messed up the definition? Any help appreciated.
Thanks,
Max
…
Grasshopper. So, I once made an attempt to bind ms sqlServer in order to get frozen definitions at some states, to avoid managing baked objects in Rhino and also be able to retain whole results without using the GH state manager that rebuilds everything.
But at that time GH's VB.Net component didn't properly read referenced dlls and I forgot it since then.
At first, I was surprised by Slingshot's extensive interface : I was still having in mind my own old project, a tool that would have acted at the Rhino's geometry object level, and auto creating the needed tables.
The bd would have consisted of a main table, owning the objects ID and name, and related tables containing the necessary information relative to the main objects.
For example, a Brep is made of so and so underlying objects, passed to respective tables, according to GH objects definition layout (just the way they are written in the xml schema).
Then, on a db, query an object by name, and retrieve the whole object or underlying objects (e.g. at the bounding curves level, or points level for a Brep).
With Slingshot, I made a few attempts to cheat GH with BLOB data fields, but no way to get a whole object. It seems that GH simply provides an object.toString ... and GH is definitely not conceived to produce persistence outside of Rhino. If I have some spare time, I will try to extract
About points and colors, I am now simply using a single field with CHAR(asLargeAsNeeded...), as GH parses String to every Point (or Vector or Color) entry of any component.
I do so because it need less to display on the canvas...
Whatever I wrote before, I really like your conception, as opened to relational interactions between ...whatever you need or dream of !
One last thing : GH can't open the definition file "Genome_DB_Template.gh" that I've downloaded from your site : http://slingshot-dev.wikidot.com/database-genome. I was expecting to learn a lot from your very smart stuff ! (I am running GH 08.00.13 and Slingshot 0.7.2.0)
Slingshot is running great, opened to any use...Thanks again.
Best,
Stan
…