0, 5, 10, 15, 20
1, 6, 11, 16, 21
2, 7, 12, 17, 22
3, 8, 13, 18, 23
4, 9, 14, 19, 24
and if i'm here is because i'm not able... :)
can you help me?
thank you
…
rve
10 curve
11 curve
12 curve
13 curve
...and I'd like to rearrange the order in which the curve are listed, to something like this:
{0,0,0}
0 curve
1 curve
8 curve
9 curve
10 curve
11 curve
2 curve
3 curve
4 curve
5 curve
12 curve
13 curve
6 curve
7 curve
I hope this makes sense.
Thank in advance for any advice,
John…
vector * number
8. number * point
9. point * number
10. complex * complex
11. colour * colour
12. colour * number
13. number * colour
--
David Rutten
david@mcneel.com
Seattle, WA…
Added by David Rutten at 10:39pm on November 12, 2010
onent are experiential or location specific. For example: humidex has been derived and widely used in Canada.Also both humidex and discomfort index should be used in in-shade conditions.For universal applications and locations, you should concentrate on either PET or UTCI (this is what "Outdoor Comfort Calculator" component is based on).
I have found out, that for instance - OutdoorComfortCalculator - which considers temperatures of 9-26 and other factors, gives the % of comfortable time outdoor for instance in Kenya in Africa (high temperatures and humidity) 55%, whereas within the same .epw data and some additional factors added to the Thermal Indices component, the "humidex" or "Discomfort index" give a result drastically lower, I think it was even 1-5% comfortable.How is that?
Yes, this is one of the issues that I have with UTCI index: the authors wanted to make it as an index applicable in any type of climate. To create the UTCI comfort categories a number of data has been collected from different locations (for hot humid climate, it was the data from Madagascar. I may be wrong on this). This resulted in universal comfortable range of 9 to 26 C which you mentioned. How would the people in Madagascar perceive the feel like temperature of 9 degrees as comfortable is beyond my understanding.Thermophysiology of a human in Madagascar, and in Poland is the same. However their acclimatization is quite different, which raises the issue with the upper universal comfortable range. In general people who live in hotter climates have a bit higher tolerance to high temperature than those living in continental climates. And vice-versa: their tolerance to lower temperatures is lower than the tolerance of the people from the continental climates. Here is a comparison of the UTCI - PET stress categories:
UTCI
all climates stress category
above +46 extreme heat stress+38 to +46 very strong heat stress+32 to +38 strong heat stress+26 to +32 moderate heat stress+9 to +26 no thermal stress+9 to 0 slight cold stress0 to -13 moderate cold stress-13 to -27 strong cold stress-27 to -40 very strong cold stressbelow -40 extreme cold stress
PET
(sub)tropical humid climate temperate climate stress categoryabove +42 above +41 extreme heat stress+38 to +42 +35 to +41 strong heat stress+34 to +38 +29 to +35 moderate heat stress+30 to +34 +23 to +29 slight heat stress+26 to +30 +18 to +23 no thermal stress+22 to +26 +13 to +18 slight cold stress+18 to +22 +8 to +13 moderate cold stress+14 to +18 +4 to +8 strong cold stressbelow +14 below +4 extreme cold stress
I attached below an example of PET humid climate comparison with UTCI, for in-shade and out-shade conditions.As it can be seen UTCI shows the percent of time comfortable: two times higher than PET.
Thank you Pin, for the useful comment, on usage of "Analysis period" component.…
EC
1. Between hours 1:00 to 24:002. Current document units is in Meters3. Conversion to Meters will be applied = 1.0004. [1 of 7] Writing simulation parameters...5. [2 of 6] No context surfaces...6. [3 of 6] Writing geometry...7. [4 of 6] Writing materials and constructions...8. [5 of 7] Writing schedules...9. [6 of 7] Writing loads and ideal air system...10. [7 of 7] Writing outputs...11. ...... idf file is successfully written to : c:\ladybug\Freeformtower_IDF\EnergyPlus\Freeformtower_IDF.idf12. 13. Analysis is running!...14. ......
Done! Read below for errors and warnings:
15. 16. Program Version,EnergyPlus-Windows-64 8.1.0.009, YMD=2015.04.04 23:39,IDD_Version 8.1.0.00917. 18. ************* IDF Context for following error/warning message:19. 20. ************* Note -- lines truncated at 300 characters, if necessary...21. 22. ************* 577 Zone,23. 24. ************* Only last 1 lines before error line shown.....25. 26. ************* 578 Freeformbuilding27. 28. ** Warning ** IP: IDF line~578 Comma being inserted after:" Freeformbuilding" in Object=ZONE29. 30. ** Severe ** Out of range value Numeric Field#5 (Type), value=0.00000, range={>=1 and <=1}, in ZONE=FREEFORMBUILDING31. 32. ************* IDF Context for following error/warning message:33. 34. ************* Note -- lines truncated at 300 characters, if necessary...35. 36. ************* 586 BuildingSurface:Detailed,7341.
…
nput parameter and then set the named values on the second?
protected override void BeforeSolveInstance() { Param_Integer param0 = Params.Input[0] as Param_Integer; Param_Integer param1 = Params.Input[1] as Param_Integer; param1.ClearNamedValues();
GH_Structure<GH_Integer> data = param0.VolatileData as GH_Structure<GH_Integer>; if (data.IsEmpty) return; foreach (GH_Integer value in data.AllData(true)) { switch (value.Value) { case 1: param1.AddNamedValue("First option for 1", 11); param1.AddNamedValue("Second option for 1", 12); param1.AddNamedValue("Third option for 1", 13); break;
case 2: param1.AddNamedValue("First option for 2", 21); param1.AddNamedValue("Second option for 2", 22); param1.AddNamedValue("Third option for 2", 23); break;
case 3: param1.AddNamedValue("First option for 3", 31); param1.AddNamedValue("Second option for 3", 32); param1.AddNamedValue("Third option for 3", 33); break; } return; } }
--
David Rutten
david@mcneel.com…
Added by David Rutten at 1:56am on December 18, 2013