pproach of estimating wind loads using design codes such as ASCE7-05.
B) Hiring a wind expert to construct a physical model and and calculate wind pressures measured directly from a wind tunnel test.
A) will allow you to derive a site specific wind design pressure based on the height of the building, surface roughness, site location etc. Typically you then multiply this pressure by an appropriate co-efficent in the code for a given building shape.
The other atypical method it to use numerical approaches such as CFD. This approach is not yet accepted due to nuances such as of surface roughness.
Building deflection is again subjective. Doing a modal analysis and getting an idea of the frequency is better. You can increase the frequency by playing about with the building stiffness.
You need to modify the stiffness of the building to get the deflection down. i.e. play about with geometry, add extra members with stiffness, reduce weight, use material with higher elastic modulus etc
If you are getting a 7m deflection for a 400m building then I can right away that is way too soft. That is equivalent to 400m/7m or H/57. You want to be at least H/500 to H/1000 so aim for 80 to 40 mm.
Your wind load seems reasonable at 87 psf for that height of building
…
oks like all your GH components are disabled? I just tried baking the cone from my earlier code and using that but can't see anything at all.
OH! You had 'Display | Shaded Preview' disabled - why? Now I see that you have 80 X 55 'SFrames', which will be VERY SLOW. I never understood why you abandon 'PopGeo'? But that many points will be extremely slow either way. I won't wait that long.
You're making this way too hard for me, bobbi.
I said early on that it's best to work with a very low count until everything works properly. Solid unions are one of the ragged edges of Grasshopper; slow and prone to failure, depending on the complexity of the geometry (co-planar surfaces, etc.).
Good luck!
P.S. I can see two problems here:
Surface normal is in instead of out.
You didn't 'Cap Holes' on the lofted tubes so they aren't solid "Closed Breps".
I have no clue what you're doing. Do you? :)…
k on forum?
or
B) install from a networked location?
Second question.
If you download from link do you:
A) read the post because you want to see what changes have occurred?
or
B) ignore the post as you are too excited to get the latest version up and running?
Third question.
When confronted by a demanding LOL cat telling you to update software do you:
A) nod approvingly and think "I must do that"?
or
B) freak out and get a sudden urge to eat cheeseburgers?
In all seriousness question three can be omitted.
EDIT: 80 views and only two posters! (thank you Simone and Luis).
I am actually interested in the results
SOLUTION TO DLL ERROR: install this …
Added by Danny Boyes at 3:32am on October 25, 2011
am to find the coverage for various public-transport stations and is interested under what conditions that coverage will poorly represent reality, then that would fit perfectly within your proposed forum, but the SO people will close it as off-topic before you can say directed-infrastructure-networks.
Or discussing which properties of a transport network would be sufficient to encode into a graph in order to give a model accurate enough for early design iterations.
Or discussing the fabrication costs under various manufacturing methods of elements (a, b, c, ...) with amounts (K, L, M, ...). ie. is it cheaper to manufacture façade panels using manual welding if I have 50*a + 50*b + 25*c or would it be cheaper to have 120*a + 3*b + 2*c?
Or discussing the visual aspects of various types of geometry. Do Bezier or Akima splines look more natural? What about them makes them look natural/unnatural? Can people tell the difference between a perfect circle and a circularish Nurbs curve with 12 points? Does it matter whether the Nurbs curve is small or big? Next to a perfect circle or not? Horizontal or vertical?
What equation would better describe experienced time by humans travelling from A to B rather than measured time?
How can I find out under what wind conditions this sharp edge on my building will start whistling?
How much might the potentially bad smell of this cheaper material lower the value of my building?…
correct:
- the right value in the 0. path {0;77} is the smallest one.
- right value in the 1. path {0;78} is the value which is closest to the chosen value in the preceding path
- ..and so on for {0;79} and {0;80}
but when the paths change their first level, the iteration should start from the beginning:
- right value in the 4. path {1;32} is the smallest one.
- right value in the 5. path {1;33} is the closest to the chosen one in {1;32}.
- right value in the 5. path {1;34} is the closest to the chosen one in {1;33}.
..to be continued.
..this is, what I want to achive in the VB code, I implemented at the beginning of the discussion.
..and this is how I designed the input-parameter of the VB-element:
if someone could help me .. super-great!
…
Mac due to its versatility , but given this new laptop will be using mainly on Rhino, GH , i have some doubts whether to switch to a window based laptop.
I have a look at some high-end window laptops, Dell Alienware for example, with same specs as MBP and found the price are even more expensive than MBP , about 10-15 %.
With the new Rhino 5 is coming , will Bootcamp be good and efficient enough to run Rhino, GH and some rendering programs?
From my experience i find Rhino and Gh run smoothly on Bootcamp , but never run those programs on window based laptop myself , it's impossible for me to know the differences.
Some say BootCamp only deliver 80% performance of the program , if it's true i would really consider switching to window based laptop.
Any suggestions?
and if you suggest me to switch , what brand should i go for ?
Thank you,
…
[2 of 8] No context surfaces...5. [3 of 8] Writing geometry...6. [4 of 8] Writing Electric Load Center - Generator specifications ...7. [5 of 8] Writing materials and constructions...8. [6 of 8] Writing schedules...9. [7 of 8] Writing loads and ideal air system...10. [8 of 8] Writing outputs...11. ...... idf file is successfully written to : C:\Users\Personal\Desktop\TESI\x006\THOR001\EnergyPlus\THOR001.idf12. 13. Analysis is running!...14. C:\Users\Personal\Desktop\TESI\x006\THOR001\EnergyPlus\eplusout.csv15. ......
Done! Read below for errors and warnings:
16. 17. Program Version,EnergyPlus, Version 8.3.0-6d97d074ea, YMD=2016.01.17 17:56,IDD_Version 8.3.018. 19. ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.20. 21. ************* Beginning Zone Sizing Calculations22. 23. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)24. 25. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00126. 27. ** ~~~ ** because vertex 1 of back surface=PELLE_NORD1 is in front of receiving surface=PELLE_COMUNIONE00128. 29. ** ~~~ ** (Dot Product indicator=184.4593)30. 31. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.32. 33. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)34. 35. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00136. 37. ** ~~~ ** because vertex 2 of back surface=PELLE_NORD1 is in front of receiving surface=PELLE_COMUNIONE00138. 39. ** ~~~ ** (Dot Product indicator=184.4593)40. 41. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.42. 43. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)44. 45. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00146. 47. ** ~~~ ** because vertex 3 of back surface=PELLE_NORD1 is in front of receiving surface=PELLE_COMUNIONE00148. 49. ** ~~~ ** (Dot Product indicator=184.4593)50. 51. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.52. 53. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)54. 55. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00156. 57. ** ~~~ ** because vertex 4 of back surface=PELLE_NORD1 is in front of receiving surface=PELLE_COMUNIONE00158. 59. ** ~~~ ** (Dot Product indicator=184.4593)60. 61. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.62. 63. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)64. 65. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00166. 67. ** ~~~ ** because vertex 1 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE00168. 69. ** ~~~ ** (Dot Product indicator=184.4593)70. 71. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.72. 73. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)74. 75. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00176. 77. ** ~~~ ** because vertex 2 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE00178. 79. ** ~~~ ** (Dot Product indicator=184.4593)80. 81. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.82. 83. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)84. 85. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00186. 87. ** ~~~ ** because vertex 3 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE00188. 89. ** ~~~ ** (Dot Product indicator=184.4593)90. 91. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.92. 93. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)94. 95. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=00196. 97. ** ~~~ ** because vertex 4 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE00198. 99. ** ~~~ ** (Dot Product indicator=184.4593)100. 101. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.102. 103. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)104. 105. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001106. 107. ** ~~~ ** because vertex 1 of back surface=PELLE_COMUNIONE002 is in front of receiving surface=PELLE_COMUNIONE001108. 109. ** ~~~ ** (Dot Product indicator=184.4593)110. 111. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.112. 113. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)114. 115. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001116. 117. ** ~~~ ** because vertex 2 of back surface=PELLE_COMUNIONE002 is in front of receiving surface=PELLE_COMUNIONE001118. 119. ** ~~~ ** (Dot Product indicator=184.4593)120. 121. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.122. 123. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)124. 125. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001126. 127. ** ~~~ ** because vertex 1 of back surface=WIN_006_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001128. 129. ** ~~~ ** (Dot Product indicator=182.6148)130. 131. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.132. 133. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)134. 135. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001136. 137. ** ~~~ ** because vertex 2 of back surface=WIN_006_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001138. 139. ** ~~~ ** (Dot Product indicator=92.2297)140. 141. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.142. 143. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)144. 145. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001146. 147. ** ~~~ ** because vertex 3 of back surface=WIN_006_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001148. 149. ** ~~~ ** (Dot Product indicator=92.2297)150. 151. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.152. 153. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)154. 155. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001156. 157. ** ~~~ ** because vertex 1 of back surface=WIN_006_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001158. 159. ** ~~~ ** (Dot Product indicator=182.6148)160. 161. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.162. 163. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)164. 165. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001166. 167. ** ~~~ ** because vertex 2 of back surface=WIN_006_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001168. 169. ** ~~~ ** (Dot Product indicator=92.2297)170. 171. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.172. 173. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)174. 175. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001176. 177. ** ~~~ ** because vertex 3 of back surface=WIN_006_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001178. 179. ** ~~~ ** (Dot Product indicator=182.6148)180. 181. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.182. 183. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)184. 185. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001186. 187. ** ~~~ ** because vertex 1 of back surface=WIN_006_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001188. 189. ** ~~~ ** (Dot Product indicator=92.2297)190. 191. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.192. 193. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)194. 195. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001196. 197. ** ~~~ ** because vertex 2 of back surface=WIN_006_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001198. 199. ** ~~~ ** (Dot Product indicator=1.8446)200. 201. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.202. 203. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)204. 205. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001206. 207. ** ~~~ ** because vertex 3 of back surface=WIN_006_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001208. 209. ** ~~~ ** (Dot Product indicator=1.8446)210. 211. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.212. 213. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)214. 215. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001216. 217. ** ~~~ ** because vertex 1 of back surface=WIN_006_GLZP_3 is in front of receiving surface=PELLE_COMUNIONE001218. 219. ** ~~~ ** (Dot Product indicator=92.2297)220. 221. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.222. 223. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)224. 225. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001226. 227. ** ~~~ ** because vertex 2 of back surface=WIN_006_GLZP_3 is in front of receiving surface=PELLE_COMUNIONE001228. 229. ** ~~~ ** (Dot Product indicator=1.8446)230. 231. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.232. 233. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)234. 235. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001236. 237. ** ~~~ ** because vertex 3 of back surface=WIN_006_GLZP_3 is in front of receiving surface=PELLE_COMUNIONE001238. 239. ** ~~~ ** (Dot Product indicator=92.2297)240. 241. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.242. 243. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)244. 245. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001246. 247. ** ~~~ ** because vertex 3 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE001248. 249. ** ~~~ ** (Dot Product indicator=184.4593)250. 251. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.252. 253. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)254. 255. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001256. 257. ** ~~~ ** because vertex 4 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE001258. 259. ** ~~~ ** (Dot Product indicator=184.4593)260. 261. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.262. 263. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)264. 265. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001266. 267. ** ~~~ ** because vertex 1 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE001268. 269. ** ~~~ ** (Dot Product indicator=184.4593)270. 271. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.272. 273. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)274. 275. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001276. 277. ** ~~~ ** because vertex 2 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE001278. 279. ** ~~~ ** (Dot Product indicator=184.4593)280. 281. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.282. 283. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)284. 285. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001286. 287. ** ~~~ ** because vertex 1 of back surface=WIN_001_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001288. 289. ** ~~~ ** (Dot Product indicator=180.7210)290. 291. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.292. 293. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)294. 295. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001296. 297. ** ~~~ ** because vertex 3 of back surface=WIN_001_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001298. 299. ** ~~~ ** (Dot Product indicator=180.7210)300. 301. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.302. 303. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)304. 305. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001306. 307. ** ~~~ ** because vertex 2 of back surface=WIN_001_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001308. 309. ** ~~~ ** (Dot Product indicator=180.7210)310. 311. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.312. 313. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)314. 315. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001316. 317. ** ~~~ ** because vertex 3 of back surface=WIN_001_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001318. 319. ** ~~~ ** (Dot Product indicator=180.7210)320. 321. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.322. 323. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)324. 325. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001326. 327. ** ~~~ ** because vertex 3 of back surface=PELLE_OVEST is in front of receiving surface=PELLE_COMUNIONE001328. 329. ** ~~~ ** (Dot Product indicator=184.4593)330. 331. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.332. 333. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)334. 335. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001336. 337. ** ~~~ ** because vertex 4 of back surface=PELLE_OVEST is in front of receiving surface=PELLE_COMUNIONE001338. 339. ** ~~~ ** (Dot Product indicator=184.4593)340. 341. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.342. 343. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)344. 345. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001346. 347. ** ~~~ ** because vertex 1 of back surface=WIN_002_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001348. 349. ** ~~~ ** (Dot Product indicator=180.7210)350. 351. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.352. 353. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)354. 355. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001356. 357. ** ~~~ ** because vertex 3 of back surface=WIN_002_GLZP_0 is in front of receiving surface=PELLE_COMUNIONE001358. 359. ** ~~~ ** (Dot Product indicator=180.7210)360. 361. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.362. 363. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)364. 365. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001366. 367. ** ~~~ ** because vertex 2 of back surface=WIN_002_GLZP_1 is in front of receiving surface=PELLE_COMUNIONE001368. 369. ** ~~~ ** (Dot Product indicator=180.7210)370. 371. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.372. 373. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)374. 375. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001376. 377. ** ~~~ ** because vertex 1 of back surface=WIN_002_GLZP_2 is in front of receiving surface=PELLE_COMUNIONE001378. 379. ** ~~~ ** (Dot Product indicator=180.7210)380. 381. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.382. 383. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)384. 385. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001386. 387. ** ~~~ ** because vertex 3 of back surface=PELLE_SOTTO is in front of receiving surface=PELLE_COMUNIONE001388. 389. ** ~~~ ** (Dot Product indicator=184.4593)390. 391. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.392. 393. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)394. 395. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001396. 397. ** ~~~ ** because vertex 4 of back surface=PELLE_SOTTO is in front of receiving surface=PELLE_COMUNIONE001398. 399. ** ~~~ ** (Dot Product indicator=184.4593)400. 401. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.402. 403. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)404. 405. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001406. 407. ** ~~~ ** because vertex 7 of back surface=PELLE_SOTTO is in front of receiving surface=PELLE_COMUNIONE001408. 409. ** ~~~ ** (Dot Product indicator=184.4593)410. 411. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.412. 413. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)414. 415. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001416. 417. ** ~~~ ** because vertex 8 of back surface=PELLE_SOTTO is in front of receiving surface=PELLE_COMUNIONE001418. 419. ** ~~~ ** (Dot Product indicator=184.4593)420. 421. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.422. 423. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)424. 425. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001426. 427. ** ~~~ ** because vertex 1 of back surface=PELLE_SOPRA_DUP is in front of receiving surface=PELLE_COMUNIONE001428. 429. ** ~~~ ** (Dot Product indicator=184.4593)430. 431. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.432. 433. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)434. 435. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001436. 437. ** ~~~ ** because vertex 4 of back surface=PELLE_SOPRA_DUP is in front of receiving surface=PELLE_COMUNIONE001438. 439. ** ~~~ ** (Dot Product indicator=184.4593)440. 441. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.442. 443. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)444. 445. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001446. 447. ** ~~~ ** because vertex 5 of back surface=PELLE_SOPRA_DUP is in front of receiving surface=PELLE_COMUNIONE001448. 449. ** ~~~ ** (Dot Product indicator=184.4593)450. 451. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.452. 453. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)454. 455. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001456. 457. ** ~~~ ** because vertex 8 of back surface=PELLE_SOPRA_DUP is in front of receiving surface=PELLE_COMUNIONE001458. 459. ** ~~~ ** (Dot Product indicator=184.4593)460. 461. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.462. 463. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)464. 465. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001466. 467. ** ~~~ ** because vertex 1 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE002468. 469. ** ~~~ ** (Dot Product indicator=167.5695)470. 471. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.472. 473. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)474. 475. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001476. 477. ** ~~~ ** because vertex 2 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE002478. 479. ** ~~~ ** (Dot Product indicator=167.5695)480. 481. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.482. 483. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)484. 485. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001486. 487. ** ~~~ ** because vertex 3 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE002488. 489. ** ~~~ ** (Dot Product indicator=195.1092)490. 491. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.492. 493. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)494. 495. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001496. 497. ** ~~~ ** because vertex 4 of back surface=PELLE_NORD2 is in front of receiving surface=PELLE_COMUNIONE002498. 499. ** ~~~ ** (Dot Product indicator=195.1092)500. 501. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.502. 503. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)504. 505. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001506. 507. ** ~~~ ** because vertex 3 of back surface=PELLE_COMUNIONE001 is in front of receiving surface=PELLE_COMUNIONE002508. 509. ** ~~~ ** (Dot Product indicator=167.5695)510. 511. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.512. 513. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)514. 515. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001516. 517. ** ~~~ ** because vertex 4 of back surface=PELLE_COMUNIONE001 is in front of receiving surface=PELLE_COMUNIONE002518. 519. ** ~~~ ** (Dot Product indicator=167.5695)520. 521. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.522. 523. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)524. 525. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001526. 527. ** ~~~ ** because vertex 1 of back surface=WIN_005 is in front of receiving surface=PELLE_COMUNIONE002528. 529. ** ~~~ ** (Dot Product indicator=32.0568)530. 531. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.532. 533. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)534. 535. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001536. 537. ** ~~~ ** because vertex 2 of back surface=WIN_005 is in front of receiving surface=PELLE_COMUNIONE002538. 539. ** ~~~ ** (Dot Product indicator=139.1556)540. 541. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.542. 543. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)544. 545. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001546. 547. ** ~~~ ** because vertex 3 of back surface=WIN_005 is in front of receiving surface=PELLE_COMUNIONE002548. 549. ** ~~~ ** (Dot Product indicator=139.1556)550. 551. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.552. 553. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)554. 555. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001556. 557. ** ~~~ ** because vertex 4 of back surface=WIN_005 is in front of receiving surface=PELLE_COMUNIONE002558. 559. ** ~~~ ** (Dot Product indicator=32.0568)560. 561. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.562. 563. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)564. 565. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001566. 567. ** ~~~ ** because vertex 1 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE002568. 569. ** ~~~ ** (Dot Product indicator=167.5695)570. 571. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.572. 573. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)574. 575. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001576. 577. ** ~~~ ** because vertex 2 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE002578. 579. ** ~~~ ** (Dot Product indicator=167.5695)580. 581. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.582. 583. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)584. 585. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001586. 587. ** ~~~ ** because vertex 3 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE002588. 589. ** ~~~ ** (Dot Product indicator=167.5695)590. 591. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.592. 593. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)594. 595. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001596. 597. ** ~~~ ** because vertex 4 of back surface=PELLE_COMUNIONE003 is in front of receiving surface=PELLE_COMUNIONE002598. 599. ** ~~~ ** (Dot Product indicator=167.5695)600. 601. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.602. 603. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)604. 605. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001606. 607. ** ~~~ ** because vertex 1 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002608. 609. ** ~~~ ** (Dot Product indicator=195.1092)610. 611. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.612. 613. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)614. 615. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001616. 617. ** ~~~ ** because vertex 2 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002618. 619. ** ~~~ ** (Dot Product indicator=195.1092)620. 621. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.622. 623. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)624. 625. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001626. 627. ** ~~~ ** because vertex 3 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002628. 629. ** ~~~ ** (Dot Product indicator=195.1092)630. 631. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.632. 633. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)634. 635. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001636. 637. ** ~~~ ** because vertex 4 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002638. 639. ** ~~~ ** (Dot Product indicator=195.1092)640. 641. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.642. 643. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)644. 645. ** ~~~ ** Solar Distribution = FullInteriorExterior will not work in Zone=001646. 647. ** ~~~ ** because vertex 5 of back surface=PELLE_EST is in front of receiving surface=PELLE_COMUNIONE002648. 649. ** ~~~ ** (Dot Product indicator=195.1092)650. 651. ** ~~~ ** Check surface geometry; if OK, use Solar Distribution = FullExterior instead.652. 653. ** Severe ** Problem in interior solar distribution calculation (CHKBKS)654. [...]
thisthe errorthat appen when i lunch E+ with only one zone....what is going on???? …
ther similar thread (by the King of HopelessEfforts) - this requires a policy for achieving rigidity (and that's 100% impossible without having a fully adaptable system for the scope).
BTW: the system that I've provided (STEP214) to you IT DOESN'T work for non planar X members (that are the norm if you use surface for the XTruss) since the X linkage is ... er .. planar. It may require (depending on the size/loads etc etc) "simple" stuff like this:
Anyway I have about 10 different systems like the above. I'll try to translate for Rhino the simplest one and I'll mail to you.
AFTER fully understanding what the whole issue is (and studying the system) you should modify your definition in order to comply with the system (but THAT is not a task for a novice by any means).
BTW: deploying a T truss on a "tensile" membrane like surface is 120% BAD engineering approach (kinda like tuning a Harley Davidson: 1M miles off topic). A tensile membrane is the obvious choice and about 12 times more economical.
more soon
…