En Mayo comienzan cursos y talleres impartidos por vortica en Ibiza.
Más info aquí:
http://vortica.es/es_copy/cursos.php
Esperamos que os resulten interesantes.
un saludo
ee 3)
{5}
0 15
{6}
0 16
And I want to place points at every possible combination of these coordinates, treating Tree 1 as X coordinates, Tree 2 as Y coordinates, and Tree 3 as Z coordinates. Also, I would like the list of points to be a tree with paths corresponding to the coordinates. Wouldn't it be nice if I could plug these trees into a Point XYZ, with a new "branch cross reference" method, and get the following result?
{0:3:5}
0 {10.0, 13.0, 15.0}
{0:3:6}
0 {10.0, 13.0, 16.0}
{0:4:5}
0 {10.0, 14.0, 15.0}
{0:4:6}
0 {10.0, 14.0, 16.0}
{1:3:5}
0 {11.0, 13.0, 15.0}
{1:3:6}
0 {11.0, 13.0, 16.0}
{1:4:5}
0 {11.0, 14.0, 15.0}
{1:4:6}
0 {11.0, 14.0, 16.0}
{2:3:5}
0 {12.0, 13.0, 15.0}
{2:3:6}
0 {12.0, 13.0, 16.0}
{2:4:5}
0 {12.0, 14.0, 15.0}
{2:4:6}
0 {12.0, 14.0, 16.0}
In this form of cross referencing, every combination of individual branches from the different lists is used as separate input, and the output for each combination is put onto a branch in the result whose path is the concatenation of the input branch paths used.…
Added by Andy Edwards at 7:03pm on November 3, 2009
EC
1. Between hours 1:00 to 24:002. Current document units is in Meters3. Conversion to Meters will be applied = 1.0004. [1 of 7] Writing simulation parameters...5. [2 of 6] No context surfaces...6. [3 of 6] Writing geometry...7. [4 of 6] Writing materials and constructions...8. [5 of 7] Writing schedules...9. [6 of 7] Writing loads and ideal air system...10. [7 of 7] Writing outputs...11. ...... idf file is successfully written to : c:\ladybug\Freeformtower_IDF\EnergyPlus\Freeformtower_IDF.idf12. 13. Analysis is running!...14. ......
Done! Read below for errors and warnings:
15. 16. Program Version,EnergyPlus-Windows-64 8.1.0.009, YMD=2015.04.04 23:39,IDD_Version 8.1.0.00917. 18. ************* IDF Context for following error/warning message:19. 20. ************* Note -- lines truncated at 300 characters, if necessary...21. 22. ************* 577 Zone,23. 24. ************* Only last 1 lines before error line shown.....25. 26. ************* 578 Freeformbuilding27. 28. ** Warning ** IP: IDF line~578 Comma being inserted after:" Freeformbuilding" in Object=ZONE29. 30. ** Severe ** Out of range value Numeric Field#5 (Type), value=0.00000, range={>=1 and <=1}, in ZONE=FREEFORMBUILDING31. 32. ************* IDF Context for following error/warning message:33. 34. ************* Note -- lines truncated at 300 characters, if necessary...35. 36. ************* 586 BuildingSurface:Detailed,7341.
…
mputer... so 1 seems strange. Also, the serial port is closed, so you wont be able to control your steppers until you open the port. Lastly, the Stepper Motor component also has to have the Start toggle set to true before actually sending values to the board. Hopefully that helps.…
should not be open).
3. All releases of Rhino 5, Arduino, GH, and FF are the latest as of May 21st.
I Boolean toggled the port open, but I can't seem to get any output to display from the UnoRead component. I was hoping to see values from any of the analog inputs (APin5 depicted) connected as info gets sent back and forth between the Arduino and my comp. I'm getting simultaneous "Hooray" and "Whoops" messages, and I can't pinpoint why. See attached JPG.
Does it have to do with the fact that I have a list of COM ports? Even though I know COM 3 is the correct one as defined in the IDE, do I need to re-declare it in Grasshopper as well? Does the {0} shown impact this output?
Any direction is appreciated.
Thanks - JFig
…