h is attached below. it`s an arch, let`s say out of bricks with loads, represented with point loads which are taken from user-defined surfaces (to represent self-wight e.g).
goal of the study is to find a supporting arch which is inside the arch then (provided the strength of the bricks is high enough) the arch is ok -otherwise one have to change the geometry of the arch (make it thicker, or change the rise of the crown).
therefore i used kangaroo in combination with galapagos to find a catenary which fulfill the boundary conditions. it works very well. so the solution galapagos found is very satisfying.
it`s simple to prove the resulting forces in the arch if one knows the rise of the arch.
according to the formula N~ q*l^2/(8*f)
with q= 21 kn/m, l= 10.00 m and f= 0.965
one get N= 272 kn, which is very near on the solution which kangaroo founds in the middle of the arch (271 kn). due to the point loads this force have to get slightly higher the nearer one comes to the anchor points. this works perfect too.
but there is one irritating thing.
at the end of the catenary, near the anchor points, kangaroo gets two very different arch-forces. 281 kn in the next to last part. and 581 kn in the very last part. this is not possible and i am sure that the value of 581 kn is wrong. i calculated the example with a commercial fea-program too. it validates the kangaroo results except the first and the last one.
i think there is a problem with the calculated end length of the first (and last) element. they are twice too long as they have to be. or do i something wrong?
thank you for any reply and again for your work.
best peter
…
Added by pb to Kangaroo at 10:25am on October 22, 2011
azione tramite interfaccia grafica 6 ore
Interfaccia Grasshopper
Parametri e Componenti
Operazione di Logica e Matematica
Vettori
Case study: concetto base di attrattore
Gestione data matching
Primi approcci alla modellazione parametrica – 4 ore
Trasformazioni di base (sposta ruota scala orienta)
Strumenti di Morphing
Utilizzo di Sweep e Loft e di altri strumenti di creazione superfici già noti da Rhinoceros
Esercitazione pratica: creazione del modello concettuale della Serpentine Gallery - B.I.G.
Focus sulla gestione dei dati - 4 ore
Creazione e gestione delle liste
Studio del data tree
Esercitazione pratica: creazione di un soffitto cassettonato
Creazione di geometrie tramite mesh – 6 ore
Utilizzo degli algoritmi di Delaunay
Utilizzo del Facet Dome
Utilizzo del Substrate
Utilizzo degli algoritmi di Voronoi
Esercitazione pratica: creazione di un gazebo attraverso l’uso di pattern
Creazione di ‘paneling’ di superfici curve – 6 ore
Discretizzazione di una superficie a doppia curvatura tramite pannelli piani
Strumenti analisi superfici
Visualizzazione superfici tramite falsi colori
Esercitazione pratica: creazione di una facciata interattiva
Digital Fabrication e messa in tavola – 6 ore
Interoperabilità tra Grasshopper e altri applicativi
Creazione di Truss parametrica
Gestione dell’abaco dei pezzi
Esercitazione pratica: la Facciata dello Stadio Friuli di Udine - Ipotesi di costruzione e gestione tramita fabbricazione digitale
Requisiti di accesso
Conoscenza delle tematiche CAD di base e dei comandi principali e interfaccia Rhinoceros 5.
Certificazioni
Alla fine del corso verranno rilasciate le certificazioni ufficiali da ART (Authorized Rhinoceros Trainer)
Numero partecipanti
Il corso parte al raggiungimento di un minimo di 4 persone ad un massimo di 8. Ogni partecipante dovrà essere munito di proprio computer con Rhinoceros.
Costo del corso
Il costo del corso è di 600 € + IVA
Sconto di 50,00 € per i giovani che hanno meno di 26 anni.
Ulteriore sconto di 50,00 € Early Bird per tutti coloro che si iscriveranno entro il 5 Settembre 2016
Nel prezzo è compresa l’iscrizione al FabLab Toscana – maggiori informazioni qui
FabLab Toscana
Il FabLab Toscana presenta un insieme di per i propri associati: sarà possibile l’accesso ai laboratori del FabLab (durante i normali orari di apertura), partecipare ai workshops gratuitamente o a prezzi calmierati, l’utilizzo della macchine (seguendo il regolamento interno), …
ow the steps of the successful run when step 1.2 is bypassed (note that the and OpenFOAM session is open in the background while running the Butterfly demo file):
1. create wind tunnel, and use different parameters of (4,4) for _globalRefLevel_ as suggested by Theodoro in this post
2. run blockMesh:
3. run snappyHexMesh:
4. run checkMesh:
5. connect the case from checkMesh to simpleFOAM and run the simulation:
6. the simulation converged at 1865 iteration, but the results visualization part has some problem:
7. so I revised this part according to suggestions from Hagit:
8. and the results can be visualized for P and U values:
The GH file used for the successful run shown above is attached here.
Now, the following is the error I got when the case from the update fvScheme component is used for simpleFOAM simulation:
the warning message on the simpleFOAM component is:
1. Solution exception: --> OpenFOAM command Failed!#0 Foam::error::printStack(Foam::Ostream&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #1 Foam::sigFpe::sigHandler(int) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #2 ? in "/lib64/libc.so.6" #3 double Foam::sumProd<double>(Foam::UList<double> const&, Foam::UList<double> const&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #4 Foam::PCG::solve(Foam::Field<double>&, Foam::Field<double> const&, unsigned char) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #5 Foam::GAMGSolver::solveCoarsestLevel(Foam::Field<double>&, Foam::Field<double> const&) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #6 Foam::GAMGSolver::Vcycle(Foam::PtrList<Foam::lduMatrix::smoother> const&, Foam::Field<double>&, Foam::Field<double> const&, Foam::Field<double>&, Foam::Field<double>&, Foam::Field<double>&, Foam::Field<double>&, Foam::Field<double>&, Foam::PtrList<Foam::Field<double> >&, Foam::PtrList<Foam::Field<double> >&, unsigned char) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #7 Foam::GAMGSolver::solve(Foam::Field<double>&, Foam::Field<double> const&, unsigned char) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #8 Foam::fvMatrix<double>::solveSegregated(Foam::dictionary const&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libfiniteVolume.so" #9 Foam::fvMatrix<double>::solve(Foam::dictionary const&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam" #10 Foam::fvMatrix<double>::solve() in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam" #11 ? in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam" #12 __libc_start_main in "/lib64/libc.so.6" #13 ? in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam"
The error message from the readMe! output node is attached below as a text file.
Hope you can kindly advise what the important steps or parameters I might have missed here. I assume it might be related to OpenFOAM rather than with the Butterfly workflow...
Thank you very much!
- Ji
…
, 2013)
The most popular year was 2008 (5 responses)
Note: According to Wikipedia: "The first version of Grasshopper, called Explicit History at the time, was originally publicly released in September 2007." Interesting coincidence.
The response to question #2 by those that began before 2007 (How long did it take for you to feel comfortable with designing computationally?):
- Years
- Don't remember, but it felt like a natural way to relate to cad.
- After a few projects
- A month.
Compared to some of the responses of those that began since 2007:
- A month
- A few months
- After 6 weeks
- About 8 weeks
- Within my second design project with GH
- five to six months
- after 1 years of self learning + over 2 years of multiple projects and continuous self learning = Computation skill is comfortable but Computational Design can not be comfortable, Crazy learning curve.
There is much diversity, but some patterns begin to emerge.
Looking forward to more responses!…
been covered since 0051 (correct me if I'm wrong):
1) Shoot for the moon first -- "Control Panel Mode" which allows for advanced interface design. See Max/MSP for example of modal function. I spent a lot of time laying out control panels so they are nice for clients and team members to look at. I spend a lot of time disabling wire display and dragging sliders and panels and graphs around into nice little clusters. Could be something as simple as a mode that disables the view of all component handles, cleans up graph objects, sliders, etc. I know the Remote Control Panel has been requested over and over again since it disappeared, but honestly it wouldn't be much use to me unless it was a full blown customizable interface. In the meantime I'll stick to my own "Canvas Control Panel" methods. (See below...)
2) More control over graph objects. Right now the bar graph for instance automatically sets the lowest and highest value displayed. Would be nice to be able to set extents manually so that you can compare apples to apples on two different lists that have different extents. Also would love to force the bar graph to show all values along x axis, not just first and last. Same goes for showing the numbers of instances for each value. Now it only shows instance numbers in oddball cases. Would like to force them to show for statistical purposes. Love percentages, but usually I also want accurate tallies. I tend to use a member index sets to generate my own lists.
3) Color input for Vectors -- there are fakey fake workarounds but none that are as versatile as simply having a color input.
4) COLOR INPUT FOR TEXT TAGS -- sorry to yell... this one really frustrates me. I often build interactive feedback systems that involve a lot of different types of data, and it is difficult to convey that input when all text is red (or green when selected).
5) Ability to justify text tags using paragraph controls -- currently default is left-justified. Would like to be able to center text horizontally and vertically, among other things.
6) Ability for text tags to handle multi-line text. Not sure the best way to implement this, but often I find myself wanting to attach 3 items of information to a particular object, and I have to string it all together in one line. Would be great if I could insert a "^M" character that stands for carriage return and have that display as multiline text (used in conjunction with above justification controls).
7) More control over Text panels. Thank you for including justification options... but sadly now it begs the question for margin and header control. Text slammed up against the left edge is pretty unsightly. Moreover, if you have labeled a text box, the drop shadow from the title bar tends to overshadow the first line of text if you have Path display turned off. Would like to add some header space to fix the problem and create a cleaner look.
8) Easier access to text font size. Buried in a Special Font... menu. I want to be able to up up down down (left right left right select start) if you know what I mean.
I guess that's it for now... just the things on the top of my head in this category. Looking forward to installing the new release, have to wait until this major project is over though.
Cheers,
Marc
…
ted (in the old scheme, all inputs were always taken into account) and it's more obvious what happens to the data just by looking at an image. Also, it clears out the component menu and it's easier to add more functionality later on without creating too much confusion.
Interpolate will 'sample' the data at equally spaced intervals. Let's say you have a list of 8 fruits, as I used in my example. What happens if you interpolate this list using 4 samples? Well, the first and last sample are always centered on the first and last items in the original list. The in between samples are distributed at equidistant intervals:
So you'd end up with a list containing {Lemon, Bergamot, Mandarin, Tangerine}. If you interpolate this list using 12 equally spaced samples, it will look like this:
and it results in a list containing {Lemon, Lime, Lime, Bergamot, Grapefruit, Grapefruit, Orange, Orange, Mandarin, Rangpur, Rangpur, Tangerine}. Of course interpolating a list may result in weird sampled intervals because of the rounding of sample parameter to list indices.
Interpolation does not sample in between values. It will not return a value that is 30% Grapefruit and 70% Orange. This kind of interpolation is only possible on a subset of data types (numbers, vectors, points, colours etc.) but these components must operate on all data types. I added a specific interpolation component as well, that performs numeric sampling using 4 possible interpolation functions, but this is a wholly different kind of interpolation.
--
David Rutten
david@mcneel.com
Poprad, Slovakia…
hit Commit.
I'm wondering how hard it would be to have an edit box which shows the
number the user could click inside of then type in a new number, then
hit enter. :)
2) How would I go about using one line from a table and assign each
field to a variable? Then, move a slider or something and use the values
from the next row?
background: I'm recreating elbows, Tees, and other fittings using
paramatric scripts, then baking and exporting them. Here's one source
table, http://www.wardfittings.com/Assets/PDFs/0902CatalogColorOld.pdf
page 5, the uniform elbows.
Current Setup: the attached ghx file. Create a point at 0,5,0 in a blank
document with units set to inches, then assign that point to the top
left 'Center Pnt' in the ghx file.
Current workflow:
a) Modify variables A, B, H, and Nominal Dia to match one line from the
table in the linked PDF file, page 5, table of regular elbows.
b) Select the 'Nodes' and 'Surfaces' with a drag box
c) Click 'Bake'
d) Switch to Rhino window, do the 'sellast' command.
e) Drag baked objects along Y axis so the center point is at 0,0,0
f) Run 'Join'
g) Run 'Cap'
h) set the 'node' points to a layer called 'nodes'
i) set the surface to a layer called 'fit-3d'.
j) select the surfaces and nodes
k) export selected
This elbow that I'm doing only has 12 rows, so doing it the above method
doesn't take THAT long. I'm also going to be doing a couple with larger
tables like the Tee on page 8, and in other spec files. As you can
imagine, entering in EACH value into a slider is a bit tedious.
I'd love to take the pdf table, run it through an OCR program to convert
to excel, modify the headers so the ghx script knows what they are, then
paste it into grasshopper, or save it and have grasshopper read it, and
I be able to move a slider or something to to select one line at a time.
Has anyone done something similar? ie: assigned one row in a table to a
predefined set of variables, each variable coming from one field in the row?
Thanks for taking the time to read this message. :)
I'm making a rhino script to do steps d-k, so that part will be much faster.
-Suthern…