ve a Vertex [V] connected to four other Vertexs [N1-N4].
Each of the has a Value:
V ... 1
N1 ... 5
N2 ... 3
N3 ... 8
N4 ... 11
The Average Filter would set the Value of [V] to
(1+5+3+8+11)/5 = 5,6
The Median Filter would Sort Values and pick the middle one
1,3, [5], 8, 11
Hope that helped...…
is shorthand for [0 to 8].
> 10 Any number larger than X. This notation is shorthand for [11 to infinity].
>= 5 Any number larger than or equal to X. This notation is shorthand for [5 to infinity].
--
David Rutten
david@mcneel.com
Seattle, WA…
Added by David Rutten at 9:27pm on November 3, 2013
13 5 15 6 17 7 ... …
But it seems I have not been clear:
the input values (3,5,7,9,11,13) should be presented in the way of "number slider" parameter. So by increasing the value of the slider from minimum 3, to 5, 7, 9, 13, 15, 17... I should get an output numbers of 0,1,3,4,5,6,7...
So I if choose value 3 on the input "number slider", on the other end, I want 0 as an output.
Or if I choose value 5 on the input "number slider", I want 1 as an output, and so on.
Is this possible?…
NONE, in SIZING:PARAMETERS". I'm not sure of where to start in troubleshooting this. I've attached the file.
Thank you,
See the errors and warnings below:
{0;0;0}
0. Current document units is in Meters
1. Conversion to Meters will be applied = 1.000
2. [1 of 8] Writing simulation parameters...
3. [2 of 8] Writing context surfaces...
4. [2 of 8] Writing context surfaces...
5. [3 of 8] Writing geometry...
6. [4 of 8] Writing Electric Load Center - Generator specifications ...
7. [5 of 8] Writing materials and constructions...
8. [6 of 8] Writing schedules...
9. [7 of 8] Writing loads and ideal air system...
10. [8 of 8] Writing outputs...
11. ...
... idf file is successfully written to : R:\Green\SuRG\Building_Performance_Analysis\2016_analysis_studies\Energy_Analysis_Comparison\Honeybee_+_Ladybug\tutorial01\EnergyPlus\tutorial01.idf
12.
13. Analysis is running!...
14. ...
...
Done! Read below for errors and warnings:
15.
16. Program Version,EnergyPlus, Version 8.5.0-c87e61b44b, YMD=2016.10.31 11:39,IDD_Version 8.5.0
17.
18. ************* IDF Context for following error/warning message:
19.
20. ************* Note -- lines truncated at 300 characters, if necessary...
21.
22. ************* 24 Sizing:Parameters,
23.
24. ************* Only last 1 lines before error line shown.....
25.
26. ************* 25 None, !- Heating Sizing Factor
27.
28. ** Severe ** IP: IDF line~25 Invalid Number in Numeric Field#1 (Heating Sizing Factor), value=NONE, in SIZING:PARAMETERS
29.
30. ** Warning ** IP: Note -- Some missing fields have been filled with defaults. See the audit output file for details.
31.
32. ** ~~~ ** Possible Invalid Numerics or other problems
33.
34. ** Fatal ** IP: Errors occurred on processing IDF file. Preceding condition(s) cause termination.
35.
36. ...Summary of Errors that led to program termination:
37.
38. ..... Reference severe error count=1
39.
40. ..... Last severe error=IP: IDF line~
, value=NONE, in SIZING:PARAMETERS
41.
42. ************* Warning: Node connection errors not checked - most system input has not been read (see previous warning).
43.
44. ************* Fatal error -- final processing. Program exited before simulations began. See previous error messages.
45.
46. ************* EnergyPlus Warmup Error Summary. During Warmup: 0 Warning; 0 Severe Errors.
47.
48. ************* EnergyPlus Sizing Error Summary. During Sizing: 0 Warning; 0 Severe Errors.
49.
50. ************* EnergyPlus Terminated--Fatal Error Detected. 1 Warning; 1 Severe Errors; Elapsed Time=00hr 00min 9.34sec
51.…
x and min values for x,y,z and calculate energy for each optionand collect these results in excel sheet ...
option No. x y z Annual coiling demand(by DIva)
1 10 10 10
2 10 15 20
3 11 10 19
4 12 14 17
5 15 16 15
6 16 11 14
7 18 12 12
.
.
etc
Regards ...
hossam
Hossam.wefki@gmail.com…
)
3. KeyError(1417,)
4. KeyError(1417,)
5. KeyError(1417,)
6. KeyError(1417,)
7. KeyError(1417,)
8. KeyError(1417,)
9. KeyError(1417,)
10. KeyError(1417,)
11.......
i tried different weather file but also same result. it seems i have same problem. the file am working on is the radiation file i took from the examples . whats seems to be the problem?
thank you for your time…
ggle A
7. Toggle A
8. Toggle 2
9. Toggle 3
10. Toggle A
11. Toggle A
12. Toggle 3
I was thinking to use somehow slider and animate option....but without luck
Any idea would be appreciated…
ints (where 2 are null). Why is it so?
The problem is that I generate only one or the first polyline of the X division wanted!
How can I fix that?
Thanks for your help...
Sam…