onsecutive points at the same height then your 'Break at discontinuities' component eliminates the middle point completely and then the 'Interpolate Curve' component gives a much bigger bump in the wrong direction. This was enough to get curves to meet from opposite sides.
I fixed this by changing the heights to 1.1 or 2.9, rather than 1.0 and 3.0, but it took a little while to work it out! Sigh.
I attach a new version. But I actually preferred it as it was before. See what you think!
Bob
p.s. in the first list, elements 11, 12, 23 and 24 go from 1 to 3; elements 17 and 18 go from 3 to 1. In the second list, elements 6, 17, 18 and 29 go from 1 to 3; elements 12 and 23 go from 3 to 1. Given the above fix, these can be easily seen.…
Added by Bob Mackay at 10:40pm on November 24, 2015
in the desired order.
0 = 0
1 = 1
2 = 6
3 = 7
4 = 8
5 = 9
6 = 12
7 = 13
8 = 2
9 = 3
10 = 4
11 = 5
12 = 10
13 = 11
Where the first number is the index and the second number is the actual sorting key. Then you sort these keys while sorting your curves in parallel using the A input of the Sort component.
--
David Rutten
david@mcneel.com
Poprad, Slovakia…
EC
1. Between hours 1:00 to 24:002. Current document units is in Meters3. Conversion to Meters will be applied = 1.0004. [1 of 7] Writing simulation parameters...5. [2 of 6] No context surfaces...6. [3 of 6] Writing geometry...7. [4 of 6] Writing materials and constructions...8. [5 of 7] Writing schedules...9. [6 of 7] Writing loads and ideal air system...10. [7 of 7] Writing outputs...11. ...... idf file is successfully written to : c:\ladybug\Freeformtower_IDF\EnergyPlus\Freeformtower_IDF.idf12. 13. Analysis is running!...14. ......
Done! Read below for errors and warnings:
15. 16. Program Version,EnergyPlus-Windows-64 8.1.0.009, YMD=2015.04.04 23:39,IDD_Version 8.1.0.00917. 18. ************* IDF Context for following error/warning message:19. 20. ************* Note -- lines truncated at 300 characters, if necessary...21. 22. ************* 577 Zone,23. 24. ************* Only last 1 lines before error line shown.....25. 26. ************* 578 Freeformbuilding27. 28. ** Warning ** IP: IDF line~578 Comma being inserted after:" Freeformbuilding" in Object=ZONE29. 30. ** Severe ** Out of range value Numeric Field#5 (Type), value=0.00000, range={>=1 and <=1}, in ZONE=FREEFORMBUILDING31. 32. ************* IDF Context for following error/warning message:33. 34. ************* Note -- lines truncated at 300 characters, if necessary...35. 36. ************* 586 BuildingSurface:Detailed,7341.
…
I've attached a rh and ghx file. http://we.tl/ghsd0UTxji - wetransfer link. I'm guessing the trick is to correctly define the Range (R) / Domain in the Random component, so that the circles' radi can vary between the fixed and static domain of 10 or 12 or 14 or 18 or 20. Meaning that the radi can only be 10, 12, 14, 18 or 20 - and not, lets say.. 11, 13, 15, 16, 17 or 19 for that matter. Thanks in advance, i hope someone can figure it out, because i can't seem to find anything online about how to set up such as specific domain.
…