ahams's question about how shades are accounted for in the simulation/thermal map and Theodore's thought that just accounting for shades in the E+ run was sufficient. I think that it may be clearest to explain what is going on with this infographic:
As the graphic shows, the thermal maps are made from 4 key types of inputs. The radiant temperature map is formed through a consideration of both the temperature of the surfaces surrounding the occupants and the direct solar radiation that might fall onto the occupants through un-shaded windows. The first surface temperature effect is easily computable from your Energy simulation results and the HBZone geometry. However, the second is calculated by seeing how sun vectors pass through the windows of the zones and uses the SolarCal method of the CBE team (http://escholarship.org/uc/item/89m1h2dg) to compute an MRT delta resulting from solar radiation. This delta is then added to the initial values computed through surface temperature view factor. When you do not connect up your shading brep geometry, internal furniture breps, or outdoor context geometry that might block sun to the additionalShading input, the thermal map will assume that sun can pass unobstructed through the window or through indoor furniture to fall onto occupants. It is important to stress that the EnergyPlus simulation does not count for blind geometry or internal furniture as actual geometry. Just as numerical abstractions of surface area and material properties. So we need you to plug in the actual geometry of these things when we compute the MRT delta resulting from sun falling directly onto people.
Next, to clear up the definition of window transmissivity. The important thing to clarify here is that, whether it refers to the tranmittance of glass or to the amount of sun coming through a fine screen of blinds, the value is multiplied by the radiation falling on the occupant and thus has a direct correlation to the MRT Delta from sun falling on occupants. So, if you set transmissivity to zero, the sun falling on the occupants will not be considered in the calculation and, if you set the transmissivity to 1, the assumption is that there is no window (or the window glass is 100% clear). So, Abraham, your definition of it as a coefficient is appropriate.
Normally, I would just recommend that you leave this value at the default 0.7, which corresponds to the transmittance of the default glass material in Honeybee. However, there are 4 cases in which you might consider changing it:
1) You are not using the default Honeybee glazing material, in which case, you should change the transmissivity to be equal to this new value.
2) You have a lot of really small blind/shade geometries and you do not want the view factor component to take several minutes to trace sun vectors through the detailed shade geometry and so you are ok with using just a simple abstraction instead of plugging shade breps into the additionaShading. In this case, you might try to estimate the average percentage of radiation coming through the blind geometry (maybe with some simple Ladybug radiation studies or with your intuition about the amount of sun blocked by the shades). You will then multiply this by the tranmissivity of your glass and this will be the value that you input to the component.
3) Your blinds for your Honeybee simulation are dynamic, in which case, plugging shade breps into additionalShading is not going to work because the component will assume that those shades are always there. In this case, you should be plugging a list of 8760 values into the transmissivity that correspond to when the shades are pulled. When the blinds are completely up, the value should be the tranmittance of your window and, when they are down, the value should be the window tranmittance multiplied by the fraction of light coming through the shades.
4) You have shades/blinds but they are transparent or are not completely opaque. The additionalShading_ input assumes that all shade geometry is opaque and so you cannot use it to account for such shades. Accordingly, you will need to account for it through the tranmissivity.
In the future, I may try to pull more information about blinds and glass properties off of the HBzones inside the view factor component but, for now and for the next few months, the above describes how it works.
Theodore, for curved geometry, I think that your safest bet is going to be planarizing the Rhino geometry before you turn it into a HBZone (so you just divide the curved surface into a few vertical planar panes of glass that approximate the curve well enough). This is essentially what the runSimulation component does for you automatically (it meshes the geometry as you see here: https://www.youtube.com/watch?v=nMQ2Pau4q6c&index=12&list=PLruLh1AdY-SgW4uDtNSMLeiUmA8YXEHT_). If I were to figure out a way to incorporate shades in this automatic meshing workflow, your EnergyPlus simulation would take a very long time to run and I am not even sure if the result will be that accurate with the way E+ abstracts shades. So I don't think that it's really worth it over just planarizing the geometry yourself.
Lastly, I won't be able to figure out the problem with your current run Theodore, unless I get the GH file from you. Make sure that you are using all up-to-date components.
-Chris…
Because the Adaptive methodology is founded upon the notion that there are hundreds of social factors that influence comfort and that the best we can do to forecast comfort is to find variables with good correlations to these social factors (like outdoor temperature), the premise that these published Adaptive model holds regardless of cultural norms is dangerous. Notably, the founders of the adaptive model have stressed that this particular linear correlation that you cite comes from recent surveys of buildings where people have both the the ability to open windows AND a great freedom to dress down. Hypothetically, if occupants were able to open the windows in Abraham's building but the cultural norm was that everyone was expected to wear multi-layered suits or dresses (as in historic Britain), a different correlation between outdoor temperature and comfort temperature would exist. In fact, historical European comfort surveys show that people likely preferred cooler temperatures in buildings (about 1-2C cooler) than today's occupants. Accordingly, after recognizing this social premise in the Adaptive model, I have built in a few ways to adjust/alter the version in Ladybug based on the literature I have read (even though these alterations are not a part of any official ASHRAE or European standard).
Abraham, you might have to be a bit more specific about how you would like to adjust the Adaptive comfort model for me to help your particular case and this may lead to me adding in new functionality. For the time being, I can tell you that the 'Ladybug_Adaptive Comfort Parameters' component is going to be your friend and I would recommend using the Adaptive Comfort Chart to visualize how you are changing the model. You can plug these 'Adaptive Comfort Parameters' into the 'Adaptive Comfort Recipe' component to have the microclimate analysis run with these parameters. Here are a few examples of how to alter the model:
1) Mixed-mode Building - Humphreys and the European Adaptive comfort team derived two separate correlations.
One for naturally ventilated buildings:
and conditioned buildings:
The dimensionless value between 0 and 1 for _levelOfConditioning allows you to create different correlations depending on whether occupants have complete freedom of dress and window operability (0) or have slight restrictions like in a mixed mode building (0.5, for example):
2) Changing Response Time of Occupants - There has been a bit of a debate in Literature about whether it is better to use the average monthly temperature or a weekly running mean temperature. The avgMonthORRunningMean input allows you to adjust this like so:
Average Month:
Running Mean:
3) Greater Temperature Range Tolerance - While this last one is actually a part of the European and Adaptive standards, you can adjust the range of the comfort band with either the 'eightyOrNintetyComf' input or the comfortClass input like so:
Ninety Percent Comfortable
Eighty Percent Comfortable
Abraham, let me know if you would like more controls over the model or if this is enough to do what you are thinking of. This example file allows you to construct the images I have above:
http://hydrashare.github.io/hydra/viewer?owner=chriswmackey&fork=hydra_2&id=Adaptive_Comfort_Chart&slide=0&scale=1&offset=0,0
-Chris…
he "return" is comment out as shown below?
After restarting Rhino and Grasshopper, I opened the outdoors_airflow demo file, and the first step of creating the case file is ok:
Then the blockMesh component gives the following error: seems I have to manually start OF first..
so, as the error message suggested, I open OF by Start_OF.bat:
Then come back to the blockMesh component, now it can be executed while the OF command line window is also openning:
... and the blockMesh finished successfully:
... so I proceeded to run snappyHexMesh, checkMesh and update fvScheme:
... up to the simpleFoam component, I got the error again:
The warning message is:
1. Solution exception: --> OpenFOAM command Failed!#0 Foam::error::printStack(Foam::Ostream&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #1 Foam::sigFpe::sigHandler(int) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #2 ? in "/lib64/libc.so.6" #3 double Foam::sumProd<double>(Foam::UList<double> const&, Foam::UList<double> const&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #4 Foam::PCG::solve(Foam::Field<double>&, Foam::Field<double> const&, unsigned char) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #5 Foam::GAMGSolver::solveCoarsestLevel(Foam::Field<double>&, Foam::Field<double> const&) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #6 Foam::GAMGSolver::Vcycle(Foam::PtrList<Foam::lduMatrix::smoother> const&, Foam::Field<double>&, Foam::Field<double> const&, Foam::Field<double>&, Foam::Field<double>&, Foam::Field<double>&, Foam::Field<double>&, Foam::Field<double>&, Foam::PtrList<Foam::Field<double> >&, Foam::PtrList<Foam::Field<double> >&, unsigned char) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #7 Foam::GAMGSolver::solve(Foam::Field<double>&, Foam::Field<double> const&, unsigned char) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #8 Foam::fvMatrix<double>::solveSegregated(Foam::dictionary const&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libfiniteVolume.so" #9 Foam::fvMatrix<double>::solve(Foam::dictionary const&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam" #10 Foam::fvMatrix<double>::solve() in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam" #11 ? in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam" #12 __libc_start_main in "/lib64/libc.so.6" #13 ? in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam"
... and the command lines in the readMe! output are pretty long and it is saved in the text file attached here.
So, my questions are:
1. why I have to manually start OF first before I can use the blockMesh component? Should butterfly automatically start OF?
2. what might be the cause of the unsuccessful run of simpleFoam in the end?
Hope you can kindly advise! Thank you!
- Ji
…
ther math and logic. i can usually conceptualise what i want to do and cobble some semi working thing together but don't know which components to use and how to patch it. so i'm super happy to have someone who knows what he's doing to find this interesting.
and i'm glad you mention the fanned frets again, there is one input parameter that's still missing for the multiscale frets to be fully parametric, it's the angle of the nut or which fret should be straight. it depends a bit on personal preferences and playing posture what is more comfortable. so being able to adjust this easily would be cool. again i have no idea how the maths for that work or if you can just rotate each fret the same amount around it's middle point. The input either as fret number (for the straight fret) or as a simple slider from bridge to nut should do as input setting.
Here are the two extremes and the middle ground:
i've been thinkin today while analysing your patches and cleaning up my mess what exactly the monster should do.
Here are the input parameters needed, i think it's the complete list
scale length low E string
scale length high e string
fret angle/straight fret
string width at nut
string width at bridge
number of frets
fretboard overhang at nut (distance from string to fretboard bounds)
fretboard overhang at last fret
string gauges
string tensions
fretboard radius at nut (for compound radius fretboard radius at bridge is calculated with the stewmac formula)
fretwire crown width
fretwire crown height
action height at nut (distance between bottom of string and fretwire crown top)
action height at last fret
pickup 1 neck position
pickup 2 middle position
pickup 3 bridge position
nut width
the pickup positions should be used to draw circles for the magnet poles on each string so they are perfectly aligned and can be used for the pickup flatwork construction. ideally they would need a rotation control aligning the center line of the pickup so it's somewher between the last fret angle and bridge angle. personally i do this visually depending on the design i'm looking for, some people have huge theories on pickup positioning but personally i don't believe in it.
that should result in everything needed to quickly generate all the necessary construction curves or geometry for nut/fingerboard/frets/pickups. this is the core of what makes a guitar work, the more precise this dynamic system is the better the guitar plays and sounds.
i posted another thread trying to understand how i could use datasets form spreadsheets,databse, csv to organize the input parameters. What would make sense for the strings for example is hook into a spreadsheet with the different string sets, i attached one for the d'Addario NYXL string line which basically covers all combos that make sense.
The string tension is an interesting one, and implmenting it would sure be overkill albeit super interesting to try. it should be possible to extrapolate from the scale length of each string what the tension for a given string gauge of that string would be so that you could say 'i want a fully balanced set' or 'heavy top light bottom) and it would calculate which SKU from d'addario would best match the required tension. All the strings listed in the spreadsheet are available as single strings to buy.
i'm trying to reorganize everything which helps me understand it. i just discovered the 'hidden wires' feature which is great since once i understood what a certain block does or have finished one of my own, i can get the wires out of the way to carry on undistracted. a bit risky to hide so many wires but it makes it so much easier not to get completely lost :-)
btw, the 'fanned fret' term is trademarked, some guy tried to patent it in the 80's which is a bit silly since it has been done for centuries. there is a level of sophistication above this as well, check out http://www.truetemperament.com/ and that really is something else. it really is astounding how superior the tuning is on those wigglefrets, the problem is that it's rather awkward for string bending and also you can't easily recrown or level the frets when they are used. …
me logic produced by running the 2-d voronoi component.
From a given set of polylines we can extract the centers and this can drive both the voronoi component as well as provide the XYZ drill points for the cnc. The definition has a variety of different options. You need Lunchbox, Weaverbird, and Starling. I can't tell you how amazing these 3 tools are from a design perspective. They are extremely powerful so if you don't have these you must install them asap. You can get the tools at http://www.food4rhino.com/
This definition works by first choosing a grid type, next you choose voronoi type, and subdivision type. From the voronoi type list you can choose basic (just grid), truncation (uses truncation calculated via the image sampler), truncation dual (uses the dual of the truncated image based grid), and subdivision (takes the basic grid type and uses different subdivision shcemes). Each of these provide different patterns of polylines from which we can extract our drilling points. I am rather proud of this definition since the overall idea is one which is so simple it's easy to overlook - the idea that drilling with a ball end mill makes voronoi plots. Now when you combine that with all of these amazing tools it can go off right quick. The nice thing is the paatern you see on screen is the pattern that gets made by drilling wysiwyg cnc patterns.
VORONIO_DRILLing.gh
Here are some on screen patterns in process in the following order truncation, basic, subdivision:
here is a video moving over a machined example:
…
l coarse mesh
Subdividing this mesh into strips of thin quads
Relaxing/Planarizing this mesh
Splitting and Unrolling
In this post I deal with the first 2 of these stages.
You can download the example definition here:
developable_strips_tutorial.gh
Drawing the initial mesh
To begin with we need a simple quad mesh. This can be modelled manually in Rhino, and only needs to use enough quads to give the topology and very rough form. No need to worry too much about the exact geometry or dimensions at this point, as we will refine and alter it as we go.
One very important thing that we do need to bear in mind though is that all internal vertices must have even valence (I covered this a bit in the earlier post here).
So for example, this is bad:
(because the highlighted vertex is surrounded by 5 faces)
While this is good (and can still be relaxed to the same shape):
(the top and bottom vertices have valence 8, and the vertices between the arms have valence 4)
With a little practice it should be possible to convert any mesh into one that meets this condition.
The reasons why we need this condition should become more clear in the later steps.
First subdivision
This is where we choose how many strips we want our final model to have, by applying a few rounds of subdivision using the Refine component (you could also use Weaverbird here):
Sorting the face directions
While quad meshes do not carry the same information about u/v directions as a NURBS surface, the individual faces do have a sort of direction given by their vertex ordering. However, these face directions are usually not consistently arranged, especially after subdivision.
The Kangaroo MeshDirection component attempts* to orient all the faces in a mesh so that they match with their neighbours.
For example, before sorting, if we draw a line from the midpoint of the first edge of each face to the midpt of its opposite edge, we might get something like this:
Whereas after sorting, we should get something like this:
*note that I say it attempts to orient the faces consistently. In some cases no valid solution exists, for instance if 3 or 5 faces meet around a vertex, hence the requirement mentioned at the start for even valence vertices.
Directional Subdivision
Now that we have consistent face directions across the mesh, we can apply further subdivision, but this time in one direction only. So we go from roughly square quads to thin rectangles. The idea is that as we apply higher levels of this directional subdivision, the final relaxed result goes towards something semi-discrete. A NURBS surface is fully continuous, and a mesh is fully discrete (made up of separate facets), while this strip model will be smooth in one direction and faceted in the other.
Go to part 2 for the next step of the process
…
eration!
See an example work flow for designing, simulating and analysing a Photovoltaic system below.
Download a Grasshopper and Rhino example file:
https://www.dropbox.com/s/krbszlplj5i40dz/017_HBgeneration%20Rhino%20model.3dm?dl=0
https://www.dropbox.com/s/lxneuzal3mipd2q/017_HBgeneration.gh?dl=0
See a quick introduction and tutorial videos here: https://www.youtube.com/playlist?list=PLrx2KnyhaJ5YXo5hpk8Q9q4Vy99O5IegK
1. Select a building to mount a photovoltaic generator on (seen in Rhino in green).
2. Select a surface within that building to mount a photovoltaic generator on (seen in Rhino in green).
3. Create a Honeybee context surface from that surface.
4. Place a photovoltaic generator on that Honeybee context surface by using the Honeybee generation component. Honeybee_Generator_PV and connecting the context surface to it's input _HBSurfaces. Then you can specify both the performance and the financial data of the photovoltaic generator.
5. Create a Honeybee generation system which consists of the photovoltaic generator in 4. By using the component Honeybee_generationsystem and connecting 4 to its input PVHBSurfaces_. Then you can specify the annual maintenance cost of this system.
6. Run the simulation in Energy Plus by connecting 5. to the input HBGenerators_.
7. Read the results of the simulation:
- The electricity produced by the Honeybee generation system in 5.
- The net purchased electricity of the facility (the Honeybee zone) to which the Honeybee generation system is attached to. This is the electricity consumed by the facility less the electricity generated by the Honeybee generation system.
- The financial costs of the Honeybee generation system; capital, maintenance and replacement costs.
8. Calculate the net present cost of the Honeybee generation system in 5 assuming a 25 year lifetime.
9. Visualise the net present cost.
…
or a couple of thingies.
Pattern.gh
I defined parametrically a triangle which I then smoothed out to become more like a blob shape. After that I created a pretty simple pattern that I had in my mind (costed me a lot of time to make this in GH) and finally wanted to rotate each element as it goes higher . The dispatching part seems to be working pretty slow, so it might need an optimization, but I’m still happy with the result as it shows exactly what I wanted, so this is a minor issue in my case.
I then decided to try tessellating my extrusions. You’ll see the voronoi script which is a blob-group in the same Pattern.gh:
I had an idea of something and started the code from scratch, then decided to watch tutorials and implement the code shown there. I somehow coped to combine my code with this in the tutorials, but since my knowledge of Grasshopper is zero to basic my code seems to be very unoptimized and lagging.. When dragging the sliders, it takes a lot of time to compute the changes, although, I’m working on a 24gigs 6th gen i7 machine. It might also need optimization.
Here comes the first tricky part that I couldn’t sort out in an elegant way neither in Grasshopper nor in Rhino. I want a smooth transition between the wall and the ceiling, so that the voronoi tessellation doesn’t get interrupted. If I was to do it in Rhino I’d make a curve with a filleted edge which I’d then revolve/sweep along a rail.
Pattern.gh:
Second thing is – I’ve defined a shape which I want to rotate at a certain degree as it goes higher, however, I don’t have the knowledge to make this happen automatically and just copy the script over and over again. Is there a chance to somehow “loop” the code and parametrically define the degree of rotation and amount of units in the loop?
Next thing is I want to somehow be able to rotate each “6-storey-building” dependently on its surrounding buildings, so that their “terraces” never overlap. I’m using quotes, since they’re still some silly shapes that have nothing to do with buildings and terraces. The principle has to be something like gear wheels or the so-called rack wheels . There has to be some pace which I could set parametrically, but I’m still unsure how to do that in Grasshopper.
The pre-last thing is that I want to control the height of each “building” based on let’s say a topography. I presume this could be done somehow with height maps or some gradient mapper connected to curvature analysis. Not really sure how something like this would work, but I’ve seen such codes that control height depending on a variable.
The last one is more or less similar to the previous. I want to be able to “dissolve” the pattern that I initially created and make it irregular. I suppose this could be done with attractor curve, but again this is just a guess. Please note that this is a top view and the shapes on the upper-left corner have got more "wings" which means there is more floors in the according building. Let's say the buildings in the upper-left corner are 6-7 floors high, in the middle are 4-5 and to the right they're only 3 floors high.
Sorry for that many questions in a single thread. Please let me know if I have to split them in separate threads. All this information is needed for learning purposes. I’m now preparing myself for my bachelor thesis and try as much things as I could, so that I’ll be ready for the final stage of my bachelor’s degree.
Many thanks in advance! Cheers!…
ooking for an efficient way to perform glazing of complex shapes.
I've only followed the Energy modelling workshops so far so i may have missed some essential components or workflows to achieve my needs. But i've made an attached definition with all my current attempts to get a proper HBzone with the numerous windows faces i will always have to deal with in this project.
I first thought that i was not using the HBObjWGZ correctly, then after some readings it was maybe an upgrading issue, then effectively i had my Therm 7.5 that needed to be reinstaled, but then ... I must be missing an essential HB tricks or workflow i guess ...
So I divided my attempt in two series :
- The Serie 1 : is a simplier version of the project step i'm working on but i'd be glad to achieve it first !
- The Serie 2 : is the real final direction of the project, which consist in sorting/dispatch faces to windowon one side and to an other material on the other, according to the winter sun and a pourcentage param.
Despite it is more complicated than the Serie one, it seems seems to create the same diversity of issues.
Until now, with the 5 different combinations of Serie 1, and the 3 of Serie 2, with and without using the different Glazing/window components, here are the logs i got from both HBZone component or OpenStudio component:
From OpenStudio - "1. The simulation has not run correctly because of this severe error: ** Severe ** BuildingSurface:Detailed="00073E23257843B6A948", invalid Construction Name="ETFE" - has Window materials.">> Has to deal with the way i'm trying to assign too early a customized EPConstruction material ? Done it wrong ? I tried to reload it in the library but doesn't change anything...
From OpenStudio - "1. The simulation has not run correctly because of this severe error: ** Severe ** BuildingSurface:Detailed="000579CD749E46DFA5EA", invalid Construction Name="EXTERIOR WINDOW" - has Window materials.">> Is it an issue in the way i define my surfs both as "WINDOW" (5) for srfType and Outdoors on the same component ?
From Create HBZone -"1. Solution exception:'EPZone' object has no attribute 'shdCntrlZoneInstructs'"
>> Happens when i try to introduce my ETFE EpMaterial after creating my first HBZone, with a Set EP Zone Construction, so this material seems to be not working either before and after trying to create an HB Zone
From Create HBZone- "1. Solution exception: 73df51a3b2144b1e858b has been moved, scaled or rotated."If you need to move or rotate a Honeybee object you should use Honeybee move, rotate or mirror components. You can find them under 12|WIP tab.
>> >> wich seems to exist in some on other thread Here and was a coding bug supposed to be fixed.
And last but not least ...
From OpenStudio - "1. The simulation has not run correctly because of this severe error: ** Severe ** checkSubSurfAzTiltNorm: Outward facing angle of subsurface differs more than 90.0 degrees from base surface.2. The simulation has failed because of this fatal error: ** Fatal ** GetSurfaceData: Errors discovered, program terminates" .
I'm attaching the file with each attempt in this post. The definitions are disabled and the log already copied separatly so there is no need to compute each of them to see what's wrong.
If someone from the beginner to one of the Kings of HoneyBee has any relevant answer/solution to this attempt with complex geometry Issue it will be really nice for me so i could to move forward !!
Thanks in advance guys and have a great day !
…
y from the Rhino model and having the absorption coefficients of the materials that are entered into Pachyderm, why is it not possible to generate a reverberation time diagram, without the need to start any analysis?
MAPPING METHOD: When for example the mapping of the Strenght Index (G) is generated through the "create map" option, succesively I can´t generate any other energy criterion map, but I have to redo the simulation.
Is it a limitation of the software or am I wrong something?
MAPPING METHOD: I kindly wanted to ask what is the difference between minimum and detailed convergence and why the number of reflections order it takes into account for the simulation is not specified. The mapping method take care only of the Raytracing Method or the Image Source too?
MAPPING METHOD: Why is the mapping value that can be exported to Rhino not generated for all the calculation raster points, but maximal only for 100 values?
MAPPING METHOD: This method hasn't been implemented in Grasshopper yet, has it?
RAYTRACING METHOD (Pach:RT): I did a raytracing through the components of GH, using only the Pach_RT, and I had these curious results in terms of time:
RaysCount: 15.000, IS_Order:1 = 5min
RaysCount: 15.000, IS_Order:2 = 12min
RaysCount: 15.000, IS_Order:3 = 3min
RaysCount: 15.000, IS_Order:4 = 8min
RaysCount: 15.000, IS_Order:5 = 3min
Why a raytracing with only 2 order, is more and more extensive than the 3/4 and 5 order?
ANALYSIS RESULT: Would there be a way to export all the results of a simulation, as is done via Odeon, to a .txt list?
I apologize in advance for asking so many questions, I hope you can find the time to answer,
Yours sincerely from Müller-BBM…