ow the steps of the successful run when step 1.2 is bypassed (note that the and OpenFOAM session is open in the background while running the Butterfly demo file):
1. create wind tunnel, and use different parameters of (4,4) for _globalRefLevel_ as suggested by Theodoro in this post
2. run blockMesh:
3. run snappyHexMesh:
4. run checkMesh:
5. connect the case from checkMesh to simpleFOAM and run the simulation:
6. the simulation converged at 1865 iteration, but the results visualization part has some problem:
7. so I revised this part according to suggestions from Hagit:
8. and the results can be visualized for P and U values:
The GH file used for the successful run shown above is attached here.
Now, the following is the error I got when the case from the update fvScheme component is used for simpleFOAM simulation:
the warning message on the simpleFOAM component is:
1. Solution exception: --> OpenFOAM command Failed!#0 Foam::error::printStack(Foam::Ostream&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #1 Foam::sigFpe::sigHandler(int) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #2 ? in "/lib64/libc.so.6" #3 double Foam::sumProd<double>(Foam::UList<double> const&, Foam::UList<double> const&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #4 Foam::PCG::solve(Foam::Field<double>&, Foam::Field<double> const&, unsigned char) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #5 Foam::GAMGSolver::solveCoarsestLevel(Foam::Field<double>&, Foam::Field<double> const&) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #6 Foam::GAMGSolver::Vcycle(Foam::PtrList<Foam::lduMatrix::smoother> const&, Foam::Field<double>&, Foam::Field<double> const&, Foam::Field<double>&, Foam::Field<double>&, Foam::Field<double>&, Foam::Field<double>&, Foam::Field<double>&, Foam::PtrList<Foam::Field<double> >&, Foam::PtrList<Foam::Field<double> >&, unsigned char) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #7 Foam::GAMGSolver::solve(Foam::Field<double>&, Foam::Field<double> const&, unsigned char) const in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libOpenFOAM.so" #8 Foam::fvMatrix<double>::solveSegregated(Foam::dictionary const&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/lib/libfiniteVolume.so" #9 Foam::fvMatrix<double>::solve(Foam::dictionary const&) in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam" #10 Foam::fvMatrix<double>::solve() in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam" #11 ? in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam" #12 __libc_start_main in "/lib64/libc.so.6" #13 ? in "/opt/OpenFOAM/OpenFOAM-v1606+/platforms/linux64GccDPInt32Opt/bin/simpleFoam"
The error message from the readMe! output node is attached below as a text file.
Hope you can kindly advise what the important steps or parameters I might have missed here. I assume it might be related to OpenFOAM rather than with the Butterfly workflow...
Thank you very much!
- Ji
…
rring to the above image)
Area
effective
effective
Second
Elastic
Elastic
Plastic
Radius
Second
Elastic
Plastic
Radius
of
Vy shear
Vz shear
Moment
Modulus
Modulus
Modulus
of
Moment
Modulus
Modulus
of
Section
Area
Area
of Area
upper
lower
Gyration
of Area
Gyration
(strong axis)
(strong axis)
(strong axis)
(strong axis)
(strong axis)
(weak axis)
(weak axis)
(weak axis)
(weak axis)
A
Ay
Az
Iy
Wy
Wy
Wply
i_y
Iz
Wz
Wplz
i_z
cm2
cm2
cm2
cm4
cm3
cm3
cm3
cm
cm4
cm3
cm3
cm
I have a very similar table which I could import to the Karamba table. But I have i_v or i_u values as well as radius of inertia for instance.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
dimensjon
Masse
Areal
akse
Ix
Wpx
ix
akse
Iy
Wpy
iy
akse
Iv
Wpv
iv
Width
Thickness
Radius R
[kg/m]
[mm2]
[mm4]
[mm3]
[mm]
[mm4]
[mm3]
[mm]
[mm4]
[mm3]
[mm]
[mm]
[mm]
[mm]
L 20x3
0.89
113
x-x
4,000
290
5.9
y-y
4,000
290
5.9
v-v
1,700
200
3.9
20
3
4
L 20x4
1.15
146
x-x
5,000
360
5.8
y-y
5,000
360
5.8
v-v
2,200
240
3.8
20
4
4
L 25x3
1.12
143
x-x
8,200
460
7.6
y-y
8,200
460
7.6
v-v
3,400
330
4.9
25
3
4
L 25x4
1.46
186
x-x
10,300
590
7.4
y-y
10,300
590
7.4
v-v
4,300
400
4.8
25
4
4
L 30x3
1.37
175
x-x
14,600
680
9.1
y-y
14,600
680
9.1
v-v
6,100
510
5.9
30
3
5
L 30x4
1.79
228
x-x
18,400
870
9.0
y-y
18,400
870
9.0
v-v
7,700
620
5.8
30
4
5
L 36x3
1.66
211
x-x
25,800
990
11.1
y-y
25,800
990
11.1
v-v
10,700
760
7.1
36
3
5
L 36x4
2.16
276
x-x
32,900
1,280
10.9
y-y
32,900
1,280
10.9
v-v
13,700
930
7.0
36
4
5
L 36x5
2.65
338
x-x
39,500
1,560
10.8
y-y
39,500
1,560
10.8
v-v
16,500
1,090
7.0
36
5
5
I have diagonals (bracings) which can buckle in these "non-regular" directions too, and they do. If I could add those values then in the Karamba model I could assign specific buckling scenarios..... I can see another challenge which will be at the ModifyElement component, I will not be able to choose these buckling lengths, in these directions.
Do you think this functionality can be added within short, or should I try to find another way to model these members?
Br, Balazs
…
but rather than keep everyone waiting, I've decided to share some as they become ready.
This also has the advantage that questions about components can be more easily grouped under the relevant post - so please do add any questions / comments / bugs / suggestions about these examples below.
So today I am posting some examples of the mesh utilities that come with the new release.
While these are not directly physics based, many of the forces and types of relaxation in Kangaroo are designed to work with meshes, and in the process of development I've ended up adding a number of simple utilities to make working with them a little easier.
I recommend also installing Weaverbird which has many more subdivision functions and other useful tools for working with meshes in Grasshopper. Also Plankton, Turtle, MeshEdit and Starling extend these possibilities still further.
Diagonalize
This component replaces every edge of a mesh with a new face. The new faces will always be quads, except for along the boundaries, where they will be triangles. It can be used to easily create diagrids. The input mesh can contain any mix of triangles and quads.
When treating the edges of a quad mesh as springs, diagonalizing it will often significantly change its physical behaviour. If you are trying to planarize a quad mesh, diagonalizing may sometimes allow you to stay closer to a target shape if it matches the curvature directions better.
diagonalize.gh
Checkerboard
This component assigns the faces of a mesh into a checkerboard pattern. The output is a list of 1s and 0s (which could represent black/white or true/false) which can be used to dispatch the faces into 2 lists, where no pair of adjacent faces have the same colour.
One nice application I found for this is applying alternating clockwise and counter-clockwise rotations as shown below. Also, on occasion you may want to planarize a quad mesh, but have some constraints on the shape and grid that prevent this, and triangulating only alternating quads to give a hybrid quad/tri mesh can sometimes be a good compromise, allowing a bit more freedom.
Note - Not all meshes can be assigned a checkerboard pattern!
As a simple example, take a mesh with 3 quads around one vertex - If we assign one black face, then both the neighbouring faces should be white, but then we have 2 white faces adjacent to one another, which violates the checkerboard condition.
Generally, we can say that if a mesh has any internal vertex with an odd number of faces around it, then we cannot apply a consistent checkerboard pattern to it (although not having any odd valence vertices is not in itself an absolute guarantee that a mesh is 'checkerboardable').
checkerboard.gh
WarpWeft
This sorts the edges of a quad mesh into 2 lists of line segments, which are like the warp and weft directions of a fabric. They can also be seen as a sort of mesh equivalent to the u and v isocurves on a NURBS surface.
This can be useful if you want to control the shape of a tension structure, because it allows you to assign different stiffnesses in the 2 directions.
As with the checkerboard component, not all meshes can be consistently assigned warp/weft directions. It follows a similar rule - all internal vertices should have an even number of adjacent faces. With a bit of care, it is usually possible to model the initial mesh in such a way as to allow this.
This component also has an output telling us whether or not each line is on a boundary of the mesh, as we will often want to treat these differently.
Same mesh relaxed with different warp/weft stiffness:
warpweft.gh
MeshCorners
This one is hopefully fairly self explanatory. In many simulations we want to anchor the corner points of a mesh. This saves us having to pick them manually in Rhino.
It works on quad meshes, and looks around the boundary vertices for any which do not have exactly 3 connected edges.
corners.gh
That's all for now. Coming soon - a "mesh tools 2" post explaining more of the components.…
as mine but couldn't manage to make it work.
The following script was working on the python module in Rhino, but not in Ghpython.
Note that I have imported a library, and it seems to be importing on Ghpython
--------------------------------------------------------------------------------------------------
from khepri.rhino import *
def iterate_quads(f, ptss):
return [[f(p0, p1, p2, p3)
for p0, p1, p2, p3
in zip(pts0, pts1, pts1[1:], pts0[1:])]
for pts0, pts1
in zip(ptss, ptss[1:])]
def iterate_hexagono(pts, n, v):
return iterate_quads(lambda p0, p1, p2, p3: hexagono_quad(p0, p1, p2, p3, n, v), pts)
def hexagono_quad(p0, p1, p2, p3, n, v):
def chapa(pts):
return intersection(extrusion(line(pts), 280), shape_from_ref(v.copy_ref(v.realize()._ref)))
#return extrusion(line(pts), -40)
topo = intermediate_loc(p3, p2) + vx(distance(p3, p2)/4 * n), intermediate_loc(p3, p2) - vx(distance(p3, p2)/4 * n)
base = intermediate_loc(p0, p1) + vx(distance(p0, p1)/4 * n), intermediate_loc(p0, p1) - vx(distance(p0, p1)/4 * n)
lateral_esq = intermediate_loc(p3, p0), intermediate_loc(p3, p0) + vx(distance(intermediate_loc(p3, p0),intermediate_loc(p2, p1))/4 * n)
lateral_dir = intermediate_loc(p2, p1), intermediate_loc(p2, p1) - vx(distance(intermediate_loc(p2, p1),intermediate_loc(p3, p0))/4 * n)
conex_1 = intermediate_loc(p3, p2) - vx(distance(p3, p2)/4 * n), intermediate_loc(p3, p0) + vx(distance(intermediate_loc(p3, p0),intermediate_loc(p2, p1))/4 * n)
conex_2 = intermediate_loc(p3, p0) + vx(distance(intermediate_loc(p3, p0), intermediate_loc(p2, p1))/4 * n), intermediate_loc(p0, p1) - vx(distance(p0, p1)/4 * n)
conex_3 = intermediate_loc(p0, p1) + vx(distance(p0, p1)/4 * n), intermediate_loc(p2, p1) - vx(distance(intermediate_loc(p2, p1),intermediate_loc(p3, p0))/4 * n)
conex_4 = intermediate_loc(p2, p1) - vx(distance(intermediate_loc(p2, p1),intermediate_loc(p3, p0))/4 * n), intermediate_loc(p3, p2) + vx(distance(p3, p2)/4 * n)
return chapa(topo), chapa(base), chapa(lateral_esq), chapa(lateral_dir), chapa(conex_1), chapa(conex_2), chapa(conex_3), chapa(conex_4)
s = prompt_shape("Escolha superficie")
v = prompt_shape("Escolha solido")
iterate_hexagono(map_surface_division(lambda p:p, s, 5, 15), 0.5, v)
---------------------------------------------------------------------------------------------------
I imported the geometry from another cad software, and then I would select the surface and solid to perform a pattern iteration on the surface to be constrained inside the solid as a internal structure.
The problem is that the surface comes with u, v and normals all weird from the other software so I wanted to pass it through Grasshopper so I can get more control and also perform other computations on Gh on the Ghpython output. Sorry, maybe I’m over complicating. All I want is the Gh inputs working on Ghpython.
I’ll attach the Gh definition,. Need help with the Ghpython component, the rest is just me fooling around.
When I try to run the sript in Ghpython I get:
Runtime error (MissingMemberException): 'NurbsSurface' object has no attribute 'realize'
Traceback:
line 39, in map_surface_division, "<string>"
I'm also attaching the module I've imported
Any help will be very appreciated and sorry about my english
Thanks!
…
l coarse mesh
Subdividing this mesh into strips of thin quads
Relaxing/Planarizing this mesh
Splitting and Unrolling
In this post I deal with the first 2 of these stages.
You can download the example definition here:
developable_strips_tutorial.gh
Drawing the initial mesh
To begin with we need a simple quad mesh. This can be modelled manually in Rhino, and only needs to use enough quads to give the topology and very rough form. No need to worry too much about the exact geometry or dimensions at this point, as we will refine and alter it as we go.
One very important thing that we do need to bear in mind though is that all internal vertices must have even valence (I covered this a bit in the earlier post here).
So for example, this is bad:
(because the highlighted vertex is surrounded by 5 faces)
While this is good (and can still be relaxed to the same shape):
(the top and bottom vertices have valence 8, and the vertices between the arms have valence 4)
With a little practice it should be possible to convert any mesh into one that meets this condition.
The reasons why we need this condition should become more clear in the later steps.
First subdivision
This is where we choose how many strips we want our final model to have, by applying a few rounds of subdivision using the Refine component (you could also use Weaverbird here):
Sorting the face directions
While quad meshes do not carry the same information about u/v directions as a NURBS surface, the individual faces do have a sort of direction given by their vertex ordering. However, these face directions are usually not consistently arranged, especially after subdivision.
The Kangaroo MeshDirection component attempts* to orient all the faces in a mesh so that they match with their neighbours.
For example, before sorting, if we draw a line from the midpoint of the first edge of each face to the midpt of its opposite edge, we might get something like this:
Whereas after sorting, we should get something like this:
*note that I say it attempts to orient the faces consistently. In some cases no valid solution exists, for instance if 3 or 5 faces meet around a vertex, hence the requirement mentioned at the start for even valence vertices.
Directional Subdivision
Now that we have consistent face directions across the mesh, we can apply further subdivision, but this time in one direction only. So we go from roughly square quads to thin rectangles. The idea is that as we apply higher levels of this directional subdivision, the final relaxed result goes towards something semi-discrete. A NURBS surface is fully continuous, and a mesh is fully discrete (made up of separate facets), while this strip model will be smooth in one direction and faceted in the other.
Go to part 2 for the next step of the process
…
le and grasshopper timer to simplify simulation control. Double click the main Kangaroo component to open this remote. There are buttons for Stop(reset), Play, Pause, and Step (moves the simulation forward one iteration).
Line-line force - allows interaction between line segments - they are treated as rigid cylinders. As with springs, there are settings for offset and rest distance, so this can be used to simulate colliding rods, and also for keeping cylinders tangent to one another (can be used for reciprocal structures).
Gear simulator - collision between curves in a plane, can be used for various mechanical simulations - cams, gears, rack and pinions etc.
Developablize force - adjusts vertices of a mesh locally, to make angles around each interior vertex sum to 2*Pi, so the mesh can be unfolded to a flat sheet without stretching.
Volume dependent pressure force - allows you to set a rest volume for a mesh instead of just a fixed pressure. When combined with Laplacian smoothing for area minimization, this can be used to optimize for CMC (constant-mean-curvature) surfaces. It will also work on open meshes.
Translation lock - maintains a fixed relationship between a pair of points. This can be used to enforce periodic boundary conditions for TPMS.
Equalize angles force - given a set of angles (defined by 3 points each), this tries to adjust them all to become equal.
Mirror symmetry force - can be used to minimize curvature variation, and optimize for higher order curve continuity. It can also be used for simulating torsional resistance in curved rods.
True minimal surface relaxation - Laplacian smoothing force now includes an option for cotangent weighting, which optimizes for zero mean curvature, unlike spring based methods, or uniform weighted Laplacian smoothing which only roughly approximate this.
Fast sphere collide - allows much faster collision detection between large numbers of spheres. By placing these spheres at the vertices, this can also be used for collision between meshes.
Force-density element - an experimental one, more on this later
Projected-force - adjusts its strength so the component of the force in a given direction stays constant.
New mesh tools:
WarpWeft - sorts the edges of a quad mesh into warp and weft directions. This can be used to assign them different stiffness in fabric form-finding.
Checkerboard - sort the faces of a mesh into 2 lists so that 2 faces of the same colour are never adjacent.
MeshDirection - sorts the vertices of a quad mesh to give it a sort of u-v directionality
Refine Strips - subdivision in one direction only - can be used to generate developable strips
Stripper - separates out the strips of quads from a larger mesh
Unroller - unfolds a quad strip to flat without stretching
MeshMap - maps points from one mesh to another (can be used together with circle-packing to generate conformal mappings)
Reciprocal structure - generates starting geometry for a reciprocal structure from any input mesh (using the Plankton mesh library *Note* If you already have the Plankton components installed, you will need to update to version 0.3.0, which is available from here)
ReMesher - adjusts the connectivity of a mesh by flipping, splitting and collapsing edges to make all edge lengths closer to a target value
Diagonalize - creates a new face for every edge of the original mesh. Can be used on quad meshes to easily convert to a diagrid.
Refine - simple non-smoothing subdivision, splitting quads into 4 quads, and triangles into 4 triangles
QuadDivide - subdivide quads by any number squared, not just powers of 4
Corners - finds the corner vertices of a quad mesh
ByParent - simple quad subdivision, keeping the output grouped by parent face.
User objects:
The download comes with an increased collection of user objects to simplify setting up common simulation types - Including a simple to use origami simulator, a reciprocal structure generator, and a tool to generate compact circle packings from a CP mesh.
General:
Geometry input now accepts polylines and straight curves.
Hinges can now be fold completely flat in both directions.
Various other minor bug fixes and speed improvements (including much faster removeDuplicatePoints/Lines components)
*****
I've not yet updated all the documentation and example files to reflect this new version, but over time I will keep posting here with new demos and explanation of all these new features. I'll try and add a few new examples each week. Vote in the comments below if there is a feature mentioned above that you're particularly keen to hear more about soon.
No doubt there are still some bugs to be discovered. If something isn't working the way you expect or want it to, please post in this forum (ideally with a description or sketch of what you think should be happening, and a clear description of what happens instead and any error messages).
There are also some more new features that weren't quite ready to make it into this release, but are on the way shortly...
Kangaroo remains completely free, for personal, academic, and commercial use. I'm always interested to hear about projects done using it, and suggestions for improvements or additions.
Daniel
…
curve or locus] of a segment AB, in English. The set of all the points from which a segment, AB, is seen under a fixed given angle.
When you construct l'arc capable —by using compass— you obviously need to find the centre of this arc. This can be easily done in GH in many ways by using some trigonometry (e.g. see previous —great— solutions). Whole circles instead of arcs provide supplementary isoptics —β-isoptic and (180º-β)-isoptic—. Coherent normals let you work in any plane.
Or you could just construct β-isoptics of AB by using tangent at A (or B). I mean [Arc SED] component.
If you want the true β-isoptic —the set of all the points— you should use {+β, -β} degrees (2 sides; 2 solutions; 2 arcs), but slider in [-180, +180] degrees provides full range of signed solutions. Orthoptic is provided by ±90º. Notice that ±180º isoptic is just AB segment itself, and 0º isoptic should be the segment outside AB —(-∞, A] U [B, +∞)—. [Radians] component is avoidable.
More compact versions can be achieved by using [F3] component. You can choose among different expressions the one you like the most as long as performs counter clockwise rotation of vector AB, by 180-β degrees, around A; or equivalent. [Panel] is totally avoidable.
Solutions in XY plane —projection; z = 0—, no matter A or B, are easy too. Just be sure about the curve you want to find the intersection with —Curve; your wall— being contained in XY plane.
A few self-explanatory examples showing features.
1 & 5 1st ver. (Supplementary isoptics) (ArcCapableTrigNormals_def_Bel.png)
2 & 6 2nd ver. (SED) (ArcCapableSED_def_Bel.png)
3 & 7 3rd ver. (SED + F3) (ArcCapableSEDF3_def_Bel.png)
4 & 8 4th ver. (SED + F3, Projection) (ArcCapableSEDProjInt_def_Bel.png)
If you want to be compact, 7 could be your best choice. If you prefer orientation robustness, 5. Etcetera.
I hope these versions will help you to compact/visualize; let me know any feedback.
Calculate where 2 points [A & B] meet at a specific angle is just find the geometrical locus called arco capaz in Spanish, arc capable in French (l'isoptique d'un segment de droite) or isoptic [curve or locus]
of a segment AB, in English. The set of all the points from which a segment,
AB, is seen under a fixed given angle.…
oftware connections built from the initial seed of the project. As always you can download the new release from Food4Rhino. Make sure to remove the older version of Ladybug and Honeybee and update your scripts.
This release is also special since today it is just about 3 years (3 years and 2 weeks) from the first release of Ladybug. As with any release, there have been a number of bug fixes and improvements but we also have some major news this time. In no specific order and to ensure that the biggest developments do not get lost in the extensive list of updates, here are the major ones:
Mostapha is re-writing Ladybug!
Ladybug for DynamoBIM is finally available.
Chris made bakeIt really useful by incorporating an export pathway to PDFs and vector-based programs.
Honeybee is now connected to THERM and the LBNL suite thanks to Chris Mackey.
Sarith has addressed a much-desired wish for Honeybee (Hi Theodore!) by adding components to model electric lighting with Radiance.
Djordje is on his way to making renewable energy deeply integrated with Ladybug by releasing components for modeling solar hot water.
There is new bug. Check the bottom of the post for Dragonfly!
Last but definitely not least (in case you’re not still convinced that this release is a major one) Miguel has started a new project that brings some of Ladybug’s features directly to Rhino. We mean Rhino Rhino - A Rhino plugin! Say hi to Icarus! #surprise
Before we forget! Ladybug and Honeybee now have official stickers. Yes! We know about T-Shirts and mugs and they will be next. For now, you can deck-out your laptops and powerhouse simulation machines with the symbology of our collaborative software ecosystem.
Now go grab a cup of tea/coffee and read the details below:
Rewriting Ladybug!
Perhaps the most far-reaching development of the last 4 months is an effort on the part of Mostapha to initiate a well structured, well documented, flexible, and extendable version of the Ladybug libraries. While such code is something that few community members will interact with directly, a well-documented library is critical for maintaining the project, adding new features, and for porting Ladybug to other software platforms.
The new Ladybug libraries are still under development across a number of new repositories and they separate a ladybug-core, which includes epw parsing and all non-geometric functions, from interface-specific geometry libraries. This allows us to easily extend Ladybug to other platforms with a different geometry library for each platform (ie. ladybug-grasshopper, ladybug-dynamo, ladybug-web, etc) all of which are developed on top of the ladybug-core.
Without getting too technical, here is an example of a useful outcome of this development. If you want to know the number of hours that relative humidity is more than 90% for a given epw, all that you have to code (in any python interface) is the following:
import ladybug as lb
_epwFile = r"C:\EnergyPlusV7-2-0\WeatherData\USA_CO_Golden-NREL.724666_TMY3.epw"
epwfile = lb.epw.EPW(_epwFile)
filteredData = epwfile.relativeHumidity.filterByConditionalStatement('x>90')
print "Number of hours with Humidity more than 90 is %d "%len(filteredData.timeStamps)
Compare that to the 500 + lines that you would have had to write previously for this operation, which were usually tied to a single interface! Now let’s see what will happen if you want to use the geometry-specific libraries. Let’s draw a sunpath in Grasshopper:
import ladybuggrasshopper.epw as epw
import ladybuggrasshopper.sunpath as sunpath
# get location data form epw file
location = epw.EPW(_epwFile).location
# initiate sunpath based on location
sp = sunpath.Sunpath.fromLocation(location, northAngle = 0, daylightSavingPeriod = None, basePoint =cenPt, scale = scale, sunScale = sunScale)
# draw sunpath geometry
sp.drawAnnualSunpath()
# assign geometries to outputs
...
Finally we ask, how would this code will look if we wanted to make a sunpath for dynamo? Well, it will be exactly the same! Just change ladybuggrasshopper in the second line to ladybugdynamo! Here is the code which is creating the sunpath below.
With this ease of scripting, we hope to involve more of our community members in our development and make it easy for others to use ladybug in their various preferred applications. By the next release, we will produce an API documentation (documentation of all the ladybug classes, methods and properties that you can script with) and begin making tutorials for those interested in getting deeper into Ladybug development.
LADYBUG
1 - Initial Release of Ladybug for Dynamo:
As is evident from the post above, we are happy to announce the first release of Ladybug for Dynamo! You can download the ladybug package from Dynamo package manager. Make sure to download version 0.0.6 which is actually 0.0.1! It took a number of trial and errors to get it up there. Once you have the file downloaded you can watch these videos to get started:
The source code can be find under ladybug-dynamo repository and (as you can already guess) it is using the new code base. It includes a very small toolkit of essential Ladybug components/nodes but it has enough to get you started. You can import weather files, draw sunpaths and run sunlighthours or radiation analyses.
There are two known issues in this release but neither of them is critical. You need to have Dynamo 0.9.1 or higher installed which you can download from here (http://dynamobuilds.com/). It is recommended that you run the scripts with ‘Manual’ run (as opposed to ‘Automatic’) since the more intense calculations can make Dynamo crash in automatic mode.
To put things in perspective, here is how we would map Ladybug for Dynamo vs Ladybug and Honeybee for Grasshopper on the classic ‘Hype graph’. The good news is that what we learned a lot from the last three years, making development of the Dynamo version easier and getting us to the plateau of productivity faster.
We should also note that the current development of the Dynamo interface is behind that of the Ladybug-Core, which means there are a number of features that are developed in the code but haven’t made their way to the nodes yet. They will be added gradually over the next month or two.
If you’re interested to get involved in the development process or have ideas for the development, follow ladybug on Facebook, Twitter and Github. We will only post major release news here. Facebook, github and twitter will be the main channels for posting the development process. There will also be a release of a new ladybug for Grasshopper soon that will use the came Ladybug-Core libraries as the Dynamo interface [Trying hard not to name it as Ladybug 2].
2 - New Project “Icarus” Provides Ladybug Capabilities Directly in Rhino
Speaking of expanded cross-platform capabilities, the talented Miguel Rus has produced a standalone Rhino Plugin off of the original Ladybug code that has been included in this release. After writing his own core C# libraries, Miguel’s plugin enables users to produce sunpath and run sunlight hours analyses in the Rhino scene without need of opening Grasshopper or engaging the (sometimes daunting) act of visual scripting.
This release includes his initial RHP plugin file. It is hoped that Miguel’s efforts will extend some of the capabilities of environmental design to individuals who are unfamiliar with visual scripting, casting the network of our community into new territory. We need your help spreading the word about Icarus since the people who will benefit the most from it have probably not read this far into the release notes. Also, as the project is in the early stages, your feedback can make a great difference. You can download the current release from this link.
Once you download the zip file. Right click and unblock it. Then extract the files under C:\Program Files\Rhinoceros 5 (64-bit)\Plug-ins\ folder. Drag and drop the RHP file into Rhino and you should be ready to go. You can either type Icarus in the command line or open it via the panels. Here is a short video that shows how to run a sunlighhours analysis study in Rhino.
3 - BakeIt Input Now Supports a Pathway to PDF +Vector Programs
As promised in the previous release, the BakeIt_ option available on Ladybug’s visual components has been enhanced to provide a full pathway to vector-based programs (like Illustrator and Inkscape) and eases the export to vector formats like PDFs.
This means that the BakeIt_ operation now places all text in the Rhino scene as actual editable text (not meshes) and any colored meshes are output as groups of colored hatches (so that they appear as color-filled polygons in vector-based programs). There is still an option to bake the colored geometries as light meshes (which requires smaller amounts of memory and computation time) but the new hatched capability should make it easier to incorporate Ladybug graphics in architectural drawings and documents like this vector psychrometric chart.
4 - Physiological Equivalent Temperature (PET) Now Available
Thanks to the efforts of Djordje Spasic, it is now possible to compute the common outdoor comfort metric ‘Physiological Equivalent Temperature’ (PET) with Ladybug. The capability has been included with this release of “Thermal Comfort Indices” component and is supported by a “Body Characteristics” component in the Extra tab. PET is particularly helpful for evaluating outdoor comfort at a high spatial resolution and so the next Honeybee release will include an option for PET with the microclimate map workflow.
5 - Solar Hot Water Components Available in WIP
Chengchu Yan and Djordje Spasic have built a set of components that perform detailed estimates of solar hot water. The components are currently undergoing final stages of testing and are available in the WIP tab of this release. You can read the full release notes for the components here.
6 - New Ladybug Graphic Standards
With the parallel efforts or so many developers, we have made an effort in this release to standardize the means by which you interact with the components. This includes warnings for missing inputs and the ability to make either icons or text appear on the components as you wish (Hi Andres!). A full list of all graphic standards can be found here. If you have any thoughts or comments on the new standards, feel free to voice them here.
7 - Wet Bulb Temperature Now Available
Thanks to Antonello Di Nunzio - the newest member of the Ladybug development team, it is now possible to calculate wet bulb temperature with Ladybug. Antonello’s component can be found under the WIP tab and takes inputs of dry bulb temperature, relative humidity, and barometric pressure.
8 - New View Analysis Types
The view analysis component now allows for several different view studies in addition to the previous ‘view to test points.’ These include, skyview (which is helpful for studies of outdoor micro-climate), as well as spherical view and ‘cone of vision’ view, which are helpful for indoor studies evaluating the overall visual connection to the outdoors.
HONEYBEE
1 - Connection to THERM and LBNL Programs
With this release, many of you will notice that a new tab has been added to Honeybee. The tab “11 | THERM” includes 7 new components that enable you to export ready-to-simulate Lawrence Berkeley National Lab (LBNL) THERM files from Rhino/Grasshopper. THERM is a 2D finite element heat flow engine that is used to evaluate the performance of wall/window construction details by simulating thermal bridging behavior. The new Honeybee tab represents the first ever CAD plugin interface for THERM, which has been in demand since the first release of LBNL THERM several years ago. The export workflow involves the drawing of window/wall construction details in Rhino and the assigning of materials and boundary conditions in Grasshopper to produce ready-to-simulate THERM files that allow you to bypass the limited drawing interface of THERM completely. Additional components in the “11 | THERM” tab allow you to import the results of THERM simulations back into Grasshopper and assist with incorporating THERM results into Honeybee EnergyPlus simulations. Finally, two components assist with a connection to LBNL WINDOW for advanced modeling of Glazing constructions. Example files illustrating many of the capabilities of the new components can be found in there links.
THERM_Export_Workflow, THERM_Comparison_of_Stud_Wall_Constructions
Analyze_THERM_Results, Thermal_Bridging_with_THERM_and_EnergyPlus
Import_Glazing_System_from_LBNL_WINDOW, Import_LBNL_WINDOW_Glazing_Assembly_for_EnergyPlus
It is recommended that those who are using these THERM components for the first time begin by exploring this example file.
Tutorial videos on how to use the components will be posted soon. A great deal of thanks is due to the LBNL team that was responsive to questions at the start of the development and special thanks goes to Payette Architects, which allowed Chris Mackey (the author of the components) a significant amount of paid time to develop them.
2 - Electrical Lighting Components with Enhanced Capabilities for Importing and Manipulating IES Files
Thanks to the efforts of Sarith Subramaniam, it is now much easier and more flexible to include electric lighting in Honeybee Radiance simulations. A series of very exciting images and videos can be found in his release post.
You can find the components under WIP tab. Sarith is looking for feedback and wishes. Please give them a try and let him know your thoughts. Several example files showing how to use the components can be found here. 1, 2, 3.
3- Expanded Dynamic Shade Capabilities
After great demand, it is now possible to assign several different types of control strategies for interior blinds and shades for EnergyPlus simulations. Control thresholds range from zone temperature, to zone cooling load, to radiation on windows, to many combinations of these variables. The new component also features the ability to run EnergyPlus simulations with electrochromic glazing. An example file showing many of the new capabilities can be found here.
Dragonfly Beta
In order to link the capabilities of Ladybug + Honeybee to a wider range of climatic data sets and analytical tools, a new insect has been initiated under the name of Dragonfly. While the Dragonfly components are not included with the download of this release, the most recent version can be downloaded here. An example file showing how to use Dragonfly to warp EPW data to account for urban heat island effect can also be found here. By the next release, the capabilities of Dragonfly should be robust enough for it to fly on its own. Additional features that will be implemented in the next few months include importing thermal satellite image data to Rhino/GH as well as the ability to warp EPW files to account for climate change projections. Anyone interested in testing out the new insect should feel free to contact Chris Mackey.
And finally, it is with great pleasure that we welcome Sarith and Antonello to the team. As mentioned in the above release notes, Sarith has added a robust implementation for electric light modeling with Honeybee and Antonello has added a component to calculate wet bulb temperature while providing stellar support to a number of people here on the GH forum.
As always let us know your comments and suggestions.
Enjoy!
Ladybug+Honeybee development team
PS: Special thanks to Chris for writing most of the release notes!…
This blog post is a rough approximation of the lecture I gave at the AAG10 conference in Vienna on September 21st 2010. Naturally it will be quite a different experience as the medium is quite…
Added by David Rutten at 3:27pm on September 24, 2010